Check the hydraulic fluid in that. That's probably low. They usually leave them low on all jacks.
@71iron13
4 ай бұрын
I believe it. My Jack had a leak I had to repair and lift wasn’t working well. I had to disassemble Jack and replace on o-ring near the spring on the side. Saved me from replacing the whole Jack. Thanks
@houndsmanone4563 Жыл бұрын
I need one of these but will check to see if HF still sells them. Will they handle weight of a Road King? Thanks 👍🏽🤠 6/27/23
@71iron13
Жыл бұрын
Harbor Freight says limit is 1000lbs. Not sure the weight of your bike. Hope that helps
@wileecoyote5749
7 ай бұрын
New ones can lift 50 Tons
@user-eo1qq4xz8w
4 ай бұрын
@@wileecoyote5749ok. Lol
@actualnatural Жыл бұрын
What’s the max height of top of your bike when fully raised?
@71iron13
Жыл бұрын
Hey sorry for the delay. Its about 78". I have a 1971 sportster
@Zeroplanetz Жыл бұрын
Hello. Do you have an issue with the table sliding when rolling the bike up on it? What am I doing wrong?
@71iron13
Жыл бұрын
There should be two threaded bolts on the front of the lower frame you can twist down to the ground.
@Zeroplanetz
Жыл бұрын
@@71iron13 yea, I’ve done that to the concrete and enough to raise the casters off the ground. But with pushing the bike up it will slide. Unless I zoom it up faster. But faster is tough to do.
@71iron13
Жыл бұрын
@@Zeroplanetz Probably a dumb question (I'm good at these) but how hard are you pushing your bike on there? I don't really ram it on there just guide it on. When I pus the bike a little harder to get the front tire into the wheel lock, the whole lift does slide forward a bit. Just a thought. You may have problems with the jack leaking oil at some point. There is an O-Ring you can replace vs buying a whole new jack from Harbor Freight. Take care
Пікірлер: 14
Check the hydraulic fluid in that. That's probably low. They usually leave them low on all jacks.
@71iron13
4 ай бұрын
I believe it. My Jack had a leak I had to repair and lift wasn’t working well. I had to disassemble Jack and replace on o-ring near the spring on the side. Saved me from replacing the whole Jack. Thanks
I need one of these but will check to see if HF still sells them. Will they handle weight of a Road King? Thanks 👍🏽🤠 6/27/23
@71iron13
Жыл бұрын
Harbor Freight says limit is 1000lbs. Not sure the weight of your bike. Hope that helps
@wileecoyote5749
7 ай бұрын
New ones can lift 50 Tons
@user-eo1qq4xz8w
4 ай бұрын
@@wileecoyote5749ok. Lol
What’s the max height of top of your bike when fully raised?
@71iron13
Жыл бұрын
Hey sorry for the delay. Its about 78". I have a 1971 sportster
Hello. Do you have an issue with the table sliding when rolling the bike up on it? What am I doing wrong?
@71iron13
Жыл бұрын
There should be two threaded bolts on the front of the lower frame you can twist down to the ground.
@Zeroplanetz
Жыл бұрын
@@71iron13 yea, I’ve done that to the concrete and enough to raise the casters off the ground. But with pushing the bike up it will slide. Unless I zoom it up faster. But faster is tough to do.
@71iron13
Жыл бұрын
@@Zeroplanetz Probably a dumb question (I'm good at these) but how hard are you pushing your bike on there? I don't really ram it on there just guide it on. When I pus the bike a little harder to get the front tire into the wheel lock, the whole lift does slide forward a bit. Just a thought. You may have problems with the jack leaking oil at some point. There is an O-Ring you can replace vs buying a whole new jack from Harbor Freight. Take care
What’s max weight
@71iron13
9 ай бұрын
harbor freight says 1000 lbs. Thanks