Here is a example of the basic grooving tool paths
Жүктеу.....
Пікірлер: 80
@eddiedante33562 сағат бұрын
Thank you so much. There aren’t a lot of videos that walk you through like this. I feel like a lot of shops gate keep knowledge to keep you underpaid. Thank you.
@ryankorn1595 Жыл бұрын
Man, I started learning machining about a month ago, and i've picked up a lot, but your videos just exponentially increased my learning with writing the program. The guy that's been teaching me is knowledgeable, but he is not a great teacher. Thank you so much! Please keep it up!
@bqualls93715 жыл бұрын
Uh, without your Grooving with Mazatrol video, I was ready to scream. Mazak manuals need a major refresh. Big thank you..................................
@bambiluong97596 жыл бұрын
this is the best video I 've learn for cnc ,please keep posting more video,thank you
@maravatio677 жыл бұрын
Thank you so much for your videos!. They're very helpful for me!!!.
@Crusaderglenn4 жыл бұрын
Thank you so much my friend i never programmed on Mazak before.This is really interesting.
@carlitoway91208 жыл бұрын
I only been programming for a month and I'm starting to get pretty good at it and I always watch your videos for reference your awesome
@everythingcnc7552
8 жыл бұрын
Thank you!
@pandorasdj8 жыл бұрын
I truly appreciate your help this is bringing back memories for me I used to program on a T-2 MAZATROL
@christophercolumbus8944
2 жыл бұрын
what do you put for grooving pitch
@pandorasdj
2 жыл бұрын
@@christophercolumbus8944 I was using the preset groove selection I just filled in the required info since it was conversational
@christophercolumbus8944
2 жыл бұрын
@@pandorasdj well no sh sherlock holmes it is conversational alright but someone i can't convey my messages to the other party pitch is 0 if it's one groove pitch is distance from one to another like threads basically
@pandorasdj
2 жыл бұрын
@@christophercolumbus8944 I have to research this man again rust has set in
@tinalieu64377 жыл бұрын
To skip to the last groove! when you're at tool path, hit right page arrow one more time, then you should see a process short cut. select the last process. you're doing an awesome job man. keep it up :)Matthew.
@Crusaderglenn
4 жыл бұрын
This is really helpful.Never checked it :D
@christophercolumbus8944
2 жыл бұрын
it didn't work very far right arrow key? goes to "layout" "store" etc how do you skip a toolpath
@christophercolumbus8944
2 жыл бұрын
@@Crusaderglenn well ? did it work for you what control do you have?
@aixcelest39194 жыл бұрын
Thank you so much for this video. I used to program older Mazatrol T1 and T2 control there is a difference how to program in grooving it seems the newer control the grooving programming is much easier.
@OpaqueWindow Жыл бұрын
Man your videos are great! Thanks a bunch
@JoseHernandez-be2ti5 жыл бұрын
Right on man 💪 keep on bringing more videos 👌
@raymondfraley7 жыл бұрын
Very helpful. Thanks I only wish the Old men with job insecurity issues at work would be so kind and show me things!
@ronaldmossolle6 жыл бұрын
Thanks really enjoy this seeing im going to be trained on a mazak smart control giving myself a head start so im not dunfounded how close is this to the smart control i wonder ?
@alejandrodavilacortes5772 Жыл бұрын
Very helpful. Thanks!
@yyaavvuuzz10 ай бұрын
You're awesome. Thank you.
@sergendogan3165
7 ай бұрын
tezgahdan anlıyomusun abi iletişim kurabilirmiyiz
@carlitoway91208 жыл бұрын
Thank you thank you brother your the best 💯💯💯
@teddymullins9737 жыл бұрын
i need help with the taper angle i have groove width start of the grove but don't know where the end of the angle is
@roozbehabbasi24976 жыл бұрын
Awesome Video. Thanksss
@pedub22228 жыл бұрын
Thanks, I'm glad to see some mazatol videos, how about some live tool stuff? I"m a fanuc guy learning mazatrol, I like the turning and the live drilling is not too bad, but the milling.......I have a lot to learn! this is a matrix control, looks close to your 640, we use some double (Y) holders and the tool data is a bit tricky, you know multiple tools for the same station on the turret (sucks) I think fanuc"s got e"m beat on that. keep up the good work!
@everythingcnc7552
8 жыл бұрын
ya I can wip up some videos on live milling this weekend. thank you.
@markallen34033 жыл бұрын
very helpful, thanks bud.
@bambiluong97597 жыл бұрын
please posting for parameter,I would like to learn about that ,thank you so much for all of you video
@multiHappyHacker4 жыл бұрын
Before I buy this Mazak Quick Turn, any idea how to use Fusion 360 to generate the programs?
@JBlinky675 жыл бұрын
Great vid. So... what if I want a .120 radius in both lower corners? Where do I add that?
@shadowdsfire
4 жыл бұрын
Just under CNR. You input the radius here.
@gertkristensen64512 жыл бұрын
best Mazatrol video . no nois good
@terryjennings23563 ай бұрын
Can you use groove option #1 with 90 degrees so the finish pass cleans the entire groove?
@middlemanclayton18 жыл бұрын
i work with fanuc controls a lot more than mazatrol, mazaks are SOOO much easier :D your vids are great man!!
@everythingcnc7552
8 жыл бұрын
thank you, let me know if there is somthing you want to see.
@everythingcnc7552
8 жыл бұрын
thank you, let me know if you have any questions on a mazak.
@fatmachinistfataman53607 жыл бұрын
hi, E CNC, thanks for making this video. I can do most anything part with canned cycle. It just the new trend now is mazaktrol program. I have a few question, Can you do some more npt thread, and blunt start??? what about face groove??. Also if you can please make some more for mill program thanks... :).... hehe i ask too much , do i??
@JScholtesInc5 жыл бұрын
Do you have any video about groove face?
@simonle10567 жыл бұрын
Would you post some video mazak milling program please?
@kratzkemachining53488 жыл бұрын
To check the process you are programming at the time you can use the restart and put in that unit or process number
@carlitoway91208 жыл бұрын
Oh ok I'm always interested in different controllers I'm running a t2 , t32-2 controller I have a qt15 and qt20 and a Atc slant turn Cnc
@thomasmedlin28812 жыл бұрын
What does the insert or tool look like?
@raffid918 жыл бұрын
Thank you. I have a one question. I wood like to use optional after some tools. I am stock. Help me if you can. For me so inportent
@raffid91
8 жыл бұрын
If you know how to use m01(optional stop)this is my email aram40@verizon.net
@marinobikes2 жыл бұрын
Gracias
@Raketni6 жыл бұрын
Mazak the best CNC machine
@davidmed91333 жыл бұрын
WHO DO YOU SET YOUR TOOL
@fatmachinistfataman53608 жыл бұрын
thank you, now i go apply for job :}
@jsnug427 жыл бұрын
You definitely do not completely suck, these video tutorials are incredibly invaluable. Is there anywhere I could download a dummy version of the Mazatrol program so I can get a better feel for how to apply your lessons?
@christophercolumbus8944
2 жыл бұрын
what kind of comment is this ? are you stupid
@ashokaekanayake73044 жыл бұрын
Thank you sir
@alexanderstefanxandraswedi58353 ай бұрын
❤
@tansit23447 жыл бұрын
Yeah I think the reason Mazatrol never clicked was I'm so stuck in EIA. Never thought of it as programming the feature, not the movement.
@carlitoway91208 жыл бұрын
What kind of Mazak are you working with and what controller are you using
@everythingcnc7552
8 жыл бұрын
QT200MY with a 640t. programming is all the same tho by the way with the exception of some added tool paths on new software
@alexandrstovpets43848 жыл бұрын
how make face grooving?
@whydahell38166 жыл бұрын
Show figure 8 ID grease grooves please.
@chilamalasubbucnc4 жыл бұрын
Sir please make one video about peanl bord how to operate the CNC machine
@romanorolex23254 жыл бұрын
How can i contact the creator of this video?
@constantinguraliuc15045 жыл бұрын
More Master
@leaftye8 жыл бұрын
You're too critical of yourself. You definitely do not suck at this. I'd say you're doing very well. I've never been on a Mazak. I can write gcode or use CAM software to make parts, but after watching your videos I feel like I could almost step up to your machine and make it look like I've been using it for a while.
@hoanguyen-tx5bl6 жыл бұрын
Thanks so much for this lesson. can u teach us face groove. thanks again.
@shadowdsfire
4 жыл бұрын
Face groove is exactly the same!
@derick3482
3 жыл бұрын
@@shadowdsfire do you know how to set G54? does mazatrol have G54? or what do you call it? in okuma i set up with ONE TOOL and then CALIBRATE other tools
@bakhtmand12094 жыл бұрын
Plz tell me any body What is programming wards mean which we use for programming how we make programming We have cnc laith mazak machine but I can't make programming because I don't know about wards I mean spt-x like all words I know cnc laith programming but onely funuc countrol
@trazy384 жыл бұрын
we just got mazak lathes with matrix nexus 2
@okelloraymond21157 жыл бұрын
thanks but the last groove, you really fucked me .....how do you decide the groove taper angle is 60, because the drawing does not say so.
Пікірлер: 80
Thank you so much. There aren’t a lot of videos that walk you through like this. I feel like a lot of shops gate keep knowledge to keep you underpaid. Thank you.
Man, I started learning machining about a month ago, and i've picked up a lot, but your videos just exponentially increased my learning with writing the program. The guy that's been teaching me is knowledgeable, but he is not a great teacher. Thank you so much! Please keep it up!
Uh, without your Grooving with Mazatrol video, I was ready to scream. Mazak manuals need a major refresh. Big thank you..................................
this is the best video I 've learn for cnc ,please keep posting more video,thank you
Thank you so much for your videos!. They're very helpful for me!!!.
Thank you so much my friend i never programmed on Mazak before.This is really interesting.
I only been programming for a month and I'm starting to get pretty good at it and I always watch your videos for reference your awesome
@everythingcnc7552
8 жыл бұрын
Thank you!
I truly appreciate your help this is bringing back memories for me I used to program on a T-2 MAZATROL
@christophercolumbus8944
2 жыл бұрын
what do you put for grooving pitch
@pandorasdj
2 жыл бұрын
@@christophercolumbus8944 I was using the preset groove selection I just filled in the required info since it was conversational
@christophercolumbus8944
2 жыл бұрын
@@pandorasdj well no sh sherlock holmes it is conversational alright but someone i can't convey my messages to the other party pitch is 0 if it's one groove pitch is distance from one to another like threads basically
@pandorasdj
2 жыл бұрын
@@christophercolumbus8944 I have to research this man again rust has set in
To skip to the last groove! when you're at tool path, hit right page arrow one more time, then you should see a process short cut. select the last process. you're doing an awesome job man. keep it up :)Matthew.
@Crusaderglenn
4 жыл бұрын
This is really helpful.Never checked it :D
@christophercolumbus8944
2 жыл бұрын
it didn't work very far right arrow key? goes to "layout" "store" etc how do you skip a toolpath
@christophercolumbus8944
2 жыл бұрын
@@Crusaderglenn well ? did it work for you what control do you have?
Thank you so much for this video. I used to program older Mazatrol T1 and T2 control there is a difference how to program in grooving it seems the newer control the grooving programming is much easier.
Man your videos are great! Thanks a bunch
Right on man 💪 keep on bringing more videos 👌
Very helpful. Thanks I only wish the Old men with job insecurity issues at work would be so kind and show me things!
Thanks really enjoy this seeing im going to be trained on a mazak smart control giving myself a head start so im not dunfounded how close is this to the smart control i wonder ?
Very helpful. Thanks!
You're awesome. Thank you.
@sergendogan3165
7 ай бұрын
tezgahdan anlıyomusun abi iletişim kurabilirmiyiz
Thank you thank you brother your the best 💯💯💯
i need help with the taper angle i have groove width start of the grove but don't know where the end of the angle is
Awesome Video. Thanksss
Thanks, I'm glad to see some mazatol videos, how about some live tool stuff? I"m a fanuc guy learning mazatrol, I like the turning and the live drilling is not too bad, but the milling.......I have a lot to learn! this is a matrix control, looks close to your 640, we use some double (Y) holders and the tool data is a bit tricky, you know multiple tools for the same station on the turret (sucks) I think fanuc"s got e"m beat on that. keep up the good work!
@everythingcnc7552
8 жыл бұрын
ya I can wip up some videos on live milling this weekend. thank you.
very helpful, thanks bud.
please posting for parameter,I would like to learn about that ,thank you so much for all of you video
Before I buy this Mazak Quick Turn, any idea how to use Fusion 360 to generate the programs?
Great vid. So... what if I want a .120 radius in both lower corners? Where do I add that?
@shadowdsfire
4 жыл бұрын
Just under CNR. You input the radius here.
best Mazatrol video . no nois good
Can you use groove option #1 with 90 degrees so the finish pass cleans the entire groove?
i work with fanuc controls a lot more than mazatrol, mazaks are SOOO much easier :D your vids are great man!!
@everythingcnc7552
8 жыл бұрын
thank you, let me know if there is somthing you want to see.
@everythingcnc7552
8 жыл бұрын
thank you, let me know if you have any questions on a mazak.
hi, E CNC, thanks for making this video. I can do most anything part with canned cycle. It just the new trend now is mazaktrol program. I have a few question, Can you do some more npt thread, and blunt start??? what about face groove??. Also if you can please make some more for mill program thanks... :).... hehe i ask too much , do i??
Do you have any video about groove face?
Would you post some video mazak milling program please?
To check the process you are programming at the time you can use the restart and put in that unit or process number
Oh ok I'm always interested in different controllers I'm running a t2 , t32-2 controller I have a qt15 and qt20 and a Atc slant turn Cnc
What does the insert or tool look like?
Thank you. I have a one question. I wood like to use optional after some tools. I am stock. Help me if you can. For me so inportent
@raffid91
8 жыл бұрын
If you know how to use m01(optional stop)this is my email aram40@verizon.net
Gracias
Mazak the best CNC machine
WHO DO YOU SET YOUR TOOL
thank you, now i go apply for job :}
You definitely do not completely suck, these video tutorials are incredibly invaluable. Is there anywhere I could download a dummy version of the Mazatrol program so I can get a better feel for how to apply your lessons?
@christophercolumbus8944
2 жыл бұрын
what kind of comment is this ? are you stupid
Thank you sir
❤
Yeah I think the reason Mazatrol never clicked was I'm so stuck in EIA. Never thought of it as programming the feature, not the movement.
What kind of Mazak are you working with and what controller are you using
@everythingcnc7552
8 жыл бұрын
QT200MY with a 640t. programming is all the same tho by the way with the exception of some added tool paths on new software
how make face grooving?
Show figure 8 ID grease grooves please.
Sir please make one video about peanl bord how to operate the CNC machine
How can i contact the creator of this video?
More Master
You're too critical of yourself. You definitely do not suck at this. I'd say you're doing very well. I've never been on a Mazak. I can write gcode or use CAM software to make parts, but after watching your videos I feel like I could almost step up to your machine and make it look like I've been using it for a while.
Thanks so much for this lesson. can u teach us face groove. thanks again.
@shadowdsfire
4 жыл бұрын
Face groove is exactly the same!
@derick3482
3 жыл бұрын
@@shadowdsfire do you know how to set G54? does mazatrol have G54? or what do you call it? in okuma i set up with ONE TOOL and then CALIBRATE other tools
Plz tell me any body What is programming wards mean which we use for programming how we make programming We have cnc laith mazak machine but I can't make programming because I don't know about wards I mean spt-x like all words I know cnc laith programming but onely funuc countrol
we just got mazak lathes with matrix nexus 2
thanks but the last groove, you really fucked me .....how do you decide the groove taper angle is 60, because the drawing does not say so.
@pakman422
7 жыл бұрын
Okello Raymond 90° minus 30° - Jacob S.
do some boring, id tapping, id threading videos
Sir plz call me job