Thanks a lot! I initially thought there were only 3…the two on the torsion bar and the one on the drive shaft. I have a 2020. There are 15 on a ‘20. They eliminated the upper two in the front. Really appreciate you posting this video.

You would think that Polaris would show a diagram in the Owner's Manual but they don't. Thanks for the video!

I have a 2015 570 Full Size and there is one more grease fitting on my Ranger (Not sure about yours). I was able to get my hands on a service manual which shows a diagram of the fitting locations. Like @computahguy commented below sure would have been nice for that to be in thr owners manual. In fact the owners manual is a bit misleading as it says the number of fittings except for thr propshaft yoke it just reads grease fittings. There's another fitting located (on my full-size anyway)underneath the center of the vehicle about 6 feet up from the one you pointed out underneath the clutch cover. Best way I've been able to grease those two fittings have been to out the vehicle in neutral and push the vehicle until you can access the fitting from the side. I can't post a picture of the diagram but trust me it's there. Hope this helps you or anyone else. Thanks for the video.

Been looking for that pilot shaft zerk! Thanks for showing me were it was located!

Awesome! I COULD NOT FIND number 17. Now I can, thanks to your video.

@StonyAcresEstate

4 жыл бұрын

Also, you can roll the Ranger forward or backward to get that #17 zerk in a place where it is easier to grease.

@RitzWood32

Жыл бұрын

That 17 is a doooozy 🙃

Just bought a used one and doing a full fluid change and grease. Your video came in handy, thanks!

@agentorange2554

2 жыл бұрын

Did you use the polaris fluids for the trans and differentials, or something else?

Thank you. This helps a lot!

Thanks for your time sir, to the point ! Awesome tutorial.

Great job, you saved me a lot of searching. Thank you!

Thanks! Just what I was looking for!

Thanks to you, sir. Exactly what was needed for my, errr, 3 year service :-0

Thank you sir! Straight to the point.

Great video.

Thanks.... this reallly helped alot.

Extremely helpful video. Thank you!

Mine is a 2020 1000 eps only fittings are back torsion bar & rear drive shaft. My 2013 900 xp is the same as yours. Always wondered about the front drive shaft. Thanks for the info. There is a tool you can buy for the wheel bearings. Not very expensive but works great.

@harthmoyer

7 ай бұрын

I have one on the front half of the shaft as I commented above. Mine is located in the middle of the vehicle. It's on the propshaft like the other tricky one but it's located about back of thr front seat in the middle. I have a full size 15 570 Ranger and there is one on my vehicle atleast. Hope this might help you or anyone else that may not know it's there.

Thanks you showed me 3 didn't know about. Tha hole for the shaft fitting probably wont work. Put it in neutral jacket up and rotate the tires unteil the fitting is looking at you. Im typing in rubber glovews so sorry about the typos

@bobdidrickson9263

5 жыл бұрын

Yea, I realized that after I posted this video. Sorry if I led anyone astray.

@quickstart-M51

4 жыл бұрын

Se109guy is right. That hole won’t work. Another way to get the Zirk where you want it is to drive the ranger about a foot and check where the fitting is. If it’s not right look at how much the shaft turned and drive it again to get it right.

I'm looking for the lube points information on a 2011 Ranger 4x4 800 EFI. I suppose its the same - Only different. Jimmy Joe

Very helpful thanks

Excellent 👍🏻

Thanks!!!!

We have a 2015 900 ranger xp and we found 20.

hi..great vid and very useful info. I need to replace a few seized ones...can you tell me what size they are?

@bobdidrickson9263

6 жыл бұрын

Sorry - Don't know. Pull one off and take it to your local store. You should be able to match it up.

Is there one on the front yoke or knuckle????

@bobdidrickson9263

6 жыл бұрын

Not really sure what a yoke or knuckle is. Sorry. All the fittings that I'm aware of I show in the video. If I missed one or more please let me and others know.

@randywise3004

6 жыл бұрын

The very last one you did is on the shaft yoke.. on my manual it says grease front shaft yoke fittings plural but I cannot find one in the front and the shaft yoke looks exactly like the one in the back

@bobdidrickson9263

6 жыл бұрын

Just went out and looked again. That last one I show is on the driveshaft U-joint. I only see one fitting on it. The one I show in the video. I checked the other U-joint by the front axle. I'm not seeing any grease fittings at all on that one.

@randywise3004

6 жыл бұрын

Bob Didrickson me either buddy but I just can't figure out why in the manual it says fittings on the Yoke shaft and that's what the manual calls it a yoke shaft I just can't figure out why there would be a grease fitting on the back on and not front .. just thought I was missing it

@bobdidrickson9263

6 жыл бұрын

No problem. Got to thank you though. As I was looking at these fitting yesterday I noticed my drive shaft is rubbing on something. Also a rubber boot on the suspension is ripped. I'll take it in to Polaris and get those looked at and while there, I'll ask them about the grease fittings. If I find out anything different I"ll let you know.

Boo is that all um. Any other mainttenance

Thanks!