One of the best guy's doing it out here great video

@ewastesolutionssonny1889

5 жыл бұрын

Check my other videos😊 awesome REFINES...

Been over 4 years Since an Upload I just came across your video and it was really a really easy way of doing it I’m steps than what everyone else shows. Hope your doing well and post Vids again.

Damn them Chip balls! Thank you Sonny for the guide!

Like cooking chicken, you have to bake those chips so they get incinerated all the way through, Fire on top doesn't finish, All these steps make a big difference in your total gold recovery, Dont worry, Making mistakes is the first steps to success, Good job, Good teacher thanks.

Excellent Video and Content..... Wear that Friggin mask brother.. Much Love and Respect.....

great video you tought me heaps Tim from Australia 👌

Nice video 👍

nice job like it

Does the gold spiral work better,in your opinion ,than the set up you have here? Thanks.

Good 👍📝

Could u answer a couple questions for me please? Do you usually do this in small batches like this? I was thinking it might be better to save up the filtered incinerated Ash, and then once I got a number of buckets full I'd go ahead and run it all. That sluice looks like it would be really frustrating to get all the stuff out of it. Have you tried one of those vibrating table things that work similarly to a sluice? I've seen a video of someone using that for their Ash material and it worked great. And that's only about a square meter plate u gotta get the gold off after. Could you please do a rough breakdown of how much it costs you to do this, and also how much weight was in the chips before you started? Then we could kinda get a better idea of the gold yeild per kelo Vs what you might get by just selling the chips to a scrapyard.

Need some commissary money bro? Lol. Wish you the best man. Hit me up when you're able. God bless, homie!

Voilà c'est comme ça qu'ils faut faire ❤

your mill looks like an acid trip when its running

Great video bro! It’s crazy actually, you put your process beside mine an almost exactly the same man except I don’t use nitric, only because I can’t pay that much for so little. Good job 👊🏻

Gravity feed through Charmin plug in funnel to get solution clear, nice setup man!

@ewastesolutionssonny1889

6 жыл бұрын

deltadawn(putyourclothesbackon) I use fiberglass plugs sometimes...but this was just a recovery video... Refining the dirty drops is another video in the future..thanks for watching. 😀

when I incinerated the thick ic chips I broke some of them. If I see black inside in the chip the incineration is not complete.

Good luck.

Dont dump the metals away because contains gold. I dissolved in acid. Whe I washed of I found lot of ash with some gold.

The safest way to treat the ash is to use somekind of hood, the ash contains ideally no carbon but a lot of metal oxides like leadoxide, a lot of metal oxides are very toxic. I don't think there will be any beryllium in there, it is used in other components like things that have to deal with a lot of heat, mostly this is white, not black.

@ewastesolutionssonny1889

6 жыл бұрын

Erwin G I meant to say cadium but need to work on my editing... Cadium is used to stabilize the plastic epoxy chips from warping with heat

I was wondering if you could do it that way. Thanks for sharing

@ewastesolutionssonny1889

5 жыл бұрын

Welcome😊

Nice work ;-)

@ewastesolutionssonny1889

6 жыл бұрын

Bohumil Graman thanks bro gonna make a little nitrosulfuric bga vid next

Great video right to the point..p S. I like your gold sluse I think I'm going to give it a try myself

You're a genius! I'm trying to recreate the process in Argentina. Can you show us more about your fume vacuum?

@ewastesolutionssonny1889

6 жыл бұрын

Lucas Markovic ewaste and precious metals refining is our gold group look into it and join all the help you need and questions will be answered....😁

@ewastesolutionssonny1889

6 жыл бұрын

Lucas Markovic on Facebook ewaste and precious metals refining

@vladyts

6 жыл бұрын

Thanks a Lot!

@vladyts

6 жыл бұрын

E WASTE SOLUTIONS SONNY request sended!

@ewastesolutionssonny1889

6 жыл бұрын

Lucas Markovic when u request you need to answer a couple questions try again😁

awesome video I subscribed Tim from Australia just found you awesome bloke

@ewastesolutionssonny1889

6 жыл бұрын

Tim Vivoda we have a good group called Ewaste and precious metals refining check it out many Aussies from the land down under in it .. thanks for subscribing

If the burnt chips glowing when hot means not incinerated. But the hot ash wont glow.

This is legit an incredible video to use for reference. I have done some research on this because I have like, 5 pounds of IC chips to incinerate...... when you incinerate, do you use a respirator? I just want to be safe and not get sick/cancer.

Hi bud good video but one thing get rid of the Facebook filming and turn your phone sideways so you get a full screen image on the tv ??????????

open flame burning is ineffective. it is better to make a primitive analogue of the blacksmith's forge, and burn in a pot on this forge. Fully burnt chips just fall apart on white dust, easily and effortlessly. good luck

poop tube is good for chunks but beach box type is better for dust.

Can you just chuck the chips into a furnace and let the them vaporize in the gold smelting process

Never watched your videos before, but you lost a whole lot of gold. I've been doing this for about 8 years. On average 500 grams of chips produces about 2 grams. I would estimate you had about 12 to 1500 grams / 3 lbs * 2 grams per lb,,,6 grams. I incinerate, wash the material through a 100 mesh while shaking it, violently, and do it again. Until there is no black material. what you will have left is a bucket of water with white ash and gold leads (your high grade). The rest of the material will have gold on the wafer plates and the wafers, some of the legs may still have gold leads attached. You can separate the wafers easily by using a magnet. What the magnet dose not pick up contains precious metals. Gold , silver, platinum and copper

Hi sir.. Can I work bga chips after incineration it by hcl and hypochlorite technique??

When you get things milled down to where you have that wire material and small chips. You can take that material and put it in a large beaker. Add a mixture of Hydrochloric Acid and Nitric Acid (Aqua Regia) and put it on low to medium heat for a few hours. That will dissolve out the gold. Then you can filter out all the particulates. Reduce the solution to near dryness, then add Hydrochloric Acid to dissolve everything remaining. Then add Sodium meta bisulfite to precipitate the dissolved gold. then you can melt that down to nearly pure gold.

@arielkozak

2 жыл бұрын

That is probably easier than what I've been doing

@nadirromero893

Жыл бұрын

Good job man.👍

Rather than useing a torch... think about building a foundry... you can control the heat and is more fuel efficient making you more profitable...

This is one of the best channels I've run across so far with the steps of gold reclamation, Thank you. I have a question or 2 or 3, Aqua regia, Is that a mixture of different acids if so how do you make it? The other acids that are not available at the hardware store, How would I obtain these? One video I saw used Cyanide of all things and it stripped the gold plate without touching the other metals! Thanks again I am subscribing.

@JTECH7766

5 жыл бұрын

Check out sreetips channel. This is ameture hour in comparison!

I suspect some of your gold is being vaporized. For the same reason, fire assay is not the best way to find microscopic gold. Try splitting a sample, acid wash half and use your propane torch on the other half. I think you'll be sadly surprised.

Not a bad video bud

If I had so many IC chips all the time, for sure after grinding everything into powder I would dissolve all the base metals in the concentrated vinegar and what is left ran through Aqua Regia without any sluicing. You are loosing gold and you know it.

Where did you get the mill

@ewastesolutionssonny1889

6 жыл бұрын

Scrapping Irish harbor freight

If you carefully boil everything in sulfuric acid it will dissolve all the iron.

Like👏👏👏👍

If you grind the ash instead of crush you will cut the bonding wires into billion pieces. Smaller gold is easier to lose. When I wash the ashes some gold wire float on top because too small. I hope you not lost any gold.

@ewastesolutionssonny1889

6 жыл бұрын

Unnamed Player I use a microscope to inspect all waste ash for any missed gold ...same with the tailings after sluce...I was planning a video with a complete incineration of ic chips and gentle ashing to keep bonding wires intacted... Soon...

@ewastesolutionssonny1889

6 жыл бұрын

Unnamed Player your absolutely right any ic chip left not grinded into ash could and will contain gold wires

Weight of ic

so the sleuse was for what....

You forgot to deactivate the nitric

where to get ic chip waste

And you can’t get any kind of amount known unless all the chips are the same ones then you can say you get. .0.70 per kilo because all the same 1 kilo of anything is an unknown???????

सीदी में दीजिए

Great video but what's the point in hours work for 1.8 g

@michaelandrews934

4 жыл бұрын

91 dollars plus refining a skill.

@DeeJayP4L

4 жыл бұрын

Spare Time Hobby that guarantees you a return anytime in the future that you need or want it. Some people play video games, others read books or play sports. Rarely do those people master those hobbies enough to turn the time-spent into actual monetary ROI (I = time-spent) - Then you can spend that same time doing something like this several times a week, and say in 5 years, while said other people are Not going pro, thus continuing the chosen hobby as only that, a hobby. This guy is watching the markets, and has done this ‘few hours of work’ about 700 times. Then one day the market for gold sky rockets due to some event in some part of the world causing massive spikes in different areas - this guy walks his peachy ass to the banks and cashed in on what he’s been casually saving for said time = Satisfied Return on Investment.

@gettingtheinsideout9683

3 жыл бұрын

Keek_is_me just explained what i really didn't know how to put into words. This explanation justified why i am scrapping all sorts of random things, and not knowing why i wanna keep doing it. Tv, and most everything online is now beyond boring lately, and this is the most satisfying thing I've done in decades... Learning, having fun, and making money is the greatest thing on earth, in my opinion.

I bet that dust is not good for your lungs.

What is the drug used here?

@ewastesolutionssonny1889

5 жыл бұрын

What are you talking about?? This is a gold recovery video!!

@donniebrown2896

4 жыл бұрын

@@ewastesolutionssonny1889 lol

@scrappydoo7887

3 жыл бұрын

@@ewastesolutionssonny1889 lol I think he's looking for meth 🤣🤣🤣🤦‍♂️

He is taking too many risk's with exposure to the dust as well as the fumes when the wind is blowing back at him. I prefer another method!

@virtualtools_3021

4 жыл бұрын

Care to enlighten us on what said method is?

Ena ena ena ena ena ena

Zu blöd im Querformat zu Filmen!

So bad

Very friendly for the environment... :(

@ewastesolutionssonny1889

5 жыл бұрын

About as bad as a car that burns oil and runs to rich😆

You dont know what you are doing. Lol