Had to pause four minutes in and comment. Well done, love how you jump into specific detailed breakdown of the existing harness and it’s functionality. This helps so much given most vids are specific to the new mod or item installed, whereas I’m reverse engineering my own setup to do fresh rewire. Being able to confirm my ideas and understanding with your video is great. Thanks 🙏🏽
@hughobrien413918 күн бұрын
I just finished up redoing my 1994 wiring harness with the help of this video. Thank you for posting this. I’m down to Vehicle Speed Sensor to run my factory speedometer. I’m not using the 4L60E wanting to use the 10L90 Or 6R80. Either way I’m not seeing a straight forward solution for keeping the factory speedometer.
@mac99552 жыл бұрын
Excellent video... Finally a detailed explanation. Now if only a video detailing a GM 1996 and newer. Thank you guys.
@swaptimeusa
2 жыл бұрын
Ah the 96 and newer is terrible to do
@mac9955
2 жыл бұрын
@@swaptimeusa Can you please briefly explain why, I have a 96 Impala SS stripped down that I'd like to swap. TY
@izq4991
2 жыл бұрын
Do you sell the harness and pcm setups for gen V ??
@swaptimeusa
2 жыл бұрын
@@izq4991 yes, Swaptimeusa.com
@vegamota6433
Жыл бұрын
My truck is a 95, would this work
@frankminakin1080 Жыл бұрын
I found this video just in time I have a 90 SS454 I’m going to install a 4l80e transmission with a USShift controller and keeping the big block but using a Holley Sniper fuel injection setup for fuel and ignition this definitely gave me a direction to go excellent videos
@GNaron Жыл бұрын
The 88-94 obs main wiring bulkhead has teeth and GM monkey snot inside. I just heated it with a propane torch, pull it apart and remove all the wires. Then I die grind out all the teeth and monkey snot of bulkhead and reuse the wiring bulkhead to pass new wires from engine compartment to the cab.
@99hawk752 жыл бұрын
What about tuning? You guys do tuning on the 17 and up lt engines?
@tbyrd32able2 жыл бұрын
I have a 94 regular cab with a 4.3 v6, I want to do a gen v l83 swap. Is there any difference I should know about as far as the v6 goes? Thanks
@shawnmalicek1189 Жыл бұрын
Is this wiring the same for a 95 k1500 thanks
@manariitahiti Жыл бұрын
I want to swap my 1190 C150 obs with a 5.3 with 4L60E trans, why don't you do a video #2 with the stand alone harness with all the connection to the obs wiring...
@lsxfirebird55802 ай бұрын
Hey I’m having some issues I have the blue wire coming out of my starter loom that’s supposed to be the knock sensor harness right And then I have a smaller grey wire with the same exact connector as the knock sensor Any clue what that might be? 1990 k1500 obs
@gregcarlos74589 ай бұрын
What is the email to ask him questions about purchasing parts for a swap
@gerardolopez5875 Жыл бұрын
How about all the a/c functions? Or they just need power from that big red wire?
@manghanson3594
7 ай бұрын
Ac runs threw Mitches new harness I believe
@613Builds2 жыл бұрын
im thinking about getting a short box 2wd obs . might have to put a 5.3 in someday
@leonrhine9571 Жыл бұрын
Have to heat it up
@dcautosparky2 жыл бұрын
Who else came back to find where the flush cuts go.. 🤚🤚
Пікірлер: 24
Had to pause four minutes in and comment. Well done, love how you jump into specific detailed breakdown of the existing harness and it’s functionality. This helps so much given most vids are specific to the new mod or item installed, whereas I’m reverse engineering my own setup to do fresh rewire. Being able to confirm my ideas and understanding with your video is great. Thanks 🙏🏽
I just finished up redoing my 1994 wiring harness with the help of this video. Thank you for posting this. I’m down to Vehicle Speed Sensor to run my factory speedometer. I’m not using the 4L60E wanting to use the 10L90 Or 6R80. Either way I’m not seeing a straight forward solution for keeping the factory speedometer.
Excellent video... Finally a detailed explanation. Now if only a video detailing a GM 1996 and newer. Thank you guys.
@swaptimeusa
2 жыл бұрын
Ah the 96 and newer is terrible to do
@mac9955
2 жыл бұрын
@@swaptimeusa Can you please briefly explain why, I have a 96 Impala SS stripped down that I'd like to swap. TY
@izq4991
2 жыл бұрын
Do you sell the harness and pcm setups for gen V ??
@swaptimeusa
2 жыл бұрын
@@izq4991 yes, Swaptimeusa.com
@vegamota6433
Жыл бұрын
My truck is a 95, would this work
I found this video just in time I have a 90 SS454 I’m going to install a 4l80e transmission with a USShift controller and keeping the big block but using a Holley Sniper fuel injection setup for fuel and ignition this definitely gave me a direction to go excellent videos
The 88-94 obs main wiring bulkhead has teeth and GM monkey snot inside. I just heated it with a propane torch, pull it apart and remove all the wires. Then I die grind out all the teeth and monkey snot of bulkhead and reuse the wiring bulkhead to pass new wires from engine compartment to the cab.
What about tuning? You guys do tuning on the 17 and up lt engines?
I have a 94 regular cab with a 4.3 v6, I want to do a gen v l83 swap. Is there any difference I should know about as far as the v6 goes? Thanks
Is this wiring the same for a 95 k1500 thanks
I want to swap my 1190 C150 obs with a 5.3 with 4L60E trans, why don't you do a video #2 with the stand alone harness with all the connection to the obs wiring...
Hey I’m having some issues I have the blue wire coming out of my starter loom that’s supposed to be the knock sensor harness right And then I have a smaller grey wire with the same exact connector as the knock sensor Any clue what that might be? 1990 k1500 obs
What is the email to ask him questions about purchasing parts for a swap
How about all the a/c functions? Or they just need power from that big red wire?
@manghanson3594
7 ай бұрын
Ac runs threw Mitches new harness I believe
im thinking about getting a short box 2wd obs . might have to put a 5.3 in someday
Have to heat it up
Who else came back to find where the flush cuts go.. 🤚🤚