No video
GM Hydraulic brake booster leak repair
New important seals with booster
Kit-501 (2771004) Hydro-Boost Seal Repair Kit, UNIVERSAL SEAL REPAIR KIT- GM, FORD, MOPAR
Music
mixkit.co/free...
Our Anthem
by Michael Ramir C.
At the Chicken Ranch
by Michael Ramir C.
Bopper from Memphis
by Michael Ramir C.
Пікірлер: 102
Thank you for this video, I put the round thing in the hole with out the plastic piece going in first and got it stuck, I wasn't sure how it reassembled until now. You saved me so much head ache and time! Thank you!
Dude... Your detail is top friggin notch
Well done! No blathering on. Excellent camera shots. You gave me a ton of confidence I'll get it right the first time.
The little yellow plastic thing was lost during disassembly.. life saver for your camera shots
@stevenpittman3676
9 ай бұрын
Did it have a small ball bearing in it
On my 93 Silverado 3/4 ton, I had a bad leak, so I tore it out, disassembled, and rebuilt with a generic (EBAY) rebuild gasket kit. It leaked. Tore that out, and realized somewhere along the tear out, and rebuilding of the original, that the accumulator became loose. That means death to the unit, and you can’t rebuild it at home. And in my application, it’s a DISCONTINUED PART ! Went to Autozone and ordered a Duralast remanufactured unit. Installed it, and it leaked. Tore that one out, brought it back to Autozone, and they ordered another one for me. Installed that one, and it leaked. I DID NOT RETURN THE SECOND UNIT FOR A REPLACEMENT. And this is my suggestion to anyone doing this rebuild. First and foremost, if the accumulator feels loose, or wobbles around and isn’t tight, your unit is toast, and you have to go with a rebuilt. Second, order a rebuilt unit from Autozone or your local parts store. Why ? For the warranty, and it’s local. I’m so glad I went that route. As for the “rebuilt unit”, it probably came from A-1 Cardone if you got it from the parts store, and that basically means it’s pretty much just what you took out of your vehicle, garbage. What did I do ? I tore out the second unit from Autozone that leaked, and disassembled as in this video. Now listen carefully here…I did not use a GENERIC REBUILD KIT FROM EBAY this time around !!!! I found a genuine GM rebuild kit on EBAY (new/old stock) and ordered that. Disassembled the unit and rebuilt it just as I did the original unit in the truck, and NO LEAKS !! The aftermarket generic gaskets are a very big “hit and miss”. These are rubber sealing rings with a VERY SPECIFIC SHAPE to them. If the tolerances are off, by even a little bit, it’s going to leak. Good luck my friends !
@eduardodavid99
9 ай бұрын
Good evening, do you know how long the push rod is?
best video yet. thanks
Cool music! And thanks for sharing!
what all yrs does that pretain too i have a 98 gmc 3500hd i got a new replacement part and it all ready has that in it so do i still take out my old one and put in the new part even it all ready has one,,,,im curious
2011 GMC Savanna 2500 4.8L looking for same kit couldn’t find one
Great video !!!
The little plunger that sits on top of the little yellow cone looking thing mine does not look like that it has three little bitty holes do they face towards me and also whenever I broke my Hydro boost and have it had pressure and sprayed all over me
You skipped half the seals
Great video! What are the torque specs for the hydroboost bolts?
@latexihire
Жыл бұрын
As I recall, 15 Nm and a screw lock.
@oscarburden8917
Жыл бұрын
22 ft lbs i believe sir
What about the seals on the push rod? I watched another video and the guy cut off the eye. Pulled the rod out replaced the seals. Put the rod back through the housing and welded the eye back on. He said he did this because he couldn't figure out how to remove it. There were no obvious ways of removing it. So I have been searching for a proper way to replace the seals.
@latexihire
7 ай бұрын
I didn't change the push rod seals there.
Nice work right on
😂 media reparación! Falto la varilla del pedal.
Awww shoooot. I just put a $300 hydroboost in my 2018 ram that I could’ve rebuilt for $20 in seal. Stupid me
@svr123456789officiel
Ай бұрын
I did the same but with 150€ shipping from the usa and 20%... to received a baddely shipping one which is all damaged
Could you show/explain/use a drawing of the proper dump valve assembly please. I'm doing a GM and not real sure of the proper reassembly mine fell out... (? Gasket, yellow plastic, pin and exterior end piece) not sure of the correct reassembly. I really would appreciate it sir, thank you
@latexihire
Жыл бұрын
Unfortunately, no information about that configuration.
That’s the same process for a 1976 Cadillac Eldorado
شكرا .. لكن خصص فيديو لكيفية فك الوصلة التي تربط بين دواسة الفرامل والبوستر الهيدروليكي... حتى يتسنى تركيب حلقات مطاط جديدة ، لمن التسريب.
@ormf1989
Жыл бұрын
Thanks .. but Dedicate a video How to disassemble the connection between the brake pedal and the hydraulic booster... so that new rubber rings can be installed, to avoid leakage.
@latexihire
Жыл бұрын
These seals did not need to be replaced on my brake booster
Que puedo aser con mi camioneta se en frena sola al darle buelta al bolante trae hidrobooster es una chebrolet modelo 98 de tres toneladas
@latexihire
5 ай бұрын
That's a special fault, it shouldn't be connected to that brake master cylinder, I'm guessing some kind of linkage problem, remove the shields from the front and examine the movements of the arms. In my Van, there was a problem with the brake hoses when the brakes were left on, the old brake hoses were swollen and the pressure remained in the work cylinder.
Buenas tardes,si fuera tan amable y pasar la reparación completa x favor
Can you advise? I am rebiilding a school bus witha chevy p30 chassis and the first thing you see when i ooen the hood is the hydroboost and master cylinder on the firewall- so i want to chrome the whole thing. The chrome shop wants onlu the external housings that need to be chromed. The whole proces will take months with back time.and shipping so the bus needs all new components anyway id buy a remanufactured boost and master and disassemble it myself and send the parts out and reasemble the chrome housing when it gets back chromed. Heres the question, how do i remove the pressure canister or does that even need to be removed ? Does it hold pressure? Is it under pressue like a nitrogen ball from a bmw brake system or is theee nothing in that canister and it should be chromed as one piece with the housing? Thats my question.
@latexihire
Жыл бұрын
Hello There is no information about disassembling the pressure tank of the brake booster.
@nestorcano5447
8 ай бұрын
informes vende repuestos
Do you think the master cylinder will cause all 4 brakes to slightly drag? I can release each one when I open the bleeder screw. Once I drive it for about 3-7 minutes it starts back dragging. I say slightly dragging because I can jack up the truck and turn them by hand with a lot of force. No leaks on the master cylinder or hydro boost. I’ve greased slider pins, bleeding the brakes 3 times, topped off the fluid on both power steering and brake fluid. Power steering is making the whining noise. Pedal is hard not soft. It’s a 2004 Suburban with hydro boost system. Please help.
@latexihire
2 ай бұрын
Operating pressure gets to the wrong place in the brake master cylinder if all brakes are stuck, usually old brake hoses do this, but only wheel-specific sticking.
@papergatorzfedducca7998
2 ай бұрын
@@latexihire yes the front brakes would stick completely and then I changed the front rubber brake hoses and now it’s slightly. So you think I should change the master cylinder?
@latexihire
2 ай бұрын
@@papergatorzfedducca7998 If it still leaves the brakes on, I would think that the fault is in the hydro booster or the master cylinder?
@papergatorzfedducca7998
2 ай бұрын
@@latexihire I’m going to released the 2 bolts on the master cylinder to see if it releases the brakes. What if it does release the brakes do I just replace the master cylinder?
@latexihire
2 ай бұрын
@@papergatorzfedducca7998 By loosening the outgoing brake pipes of the brake master cylinder, you can see if the pressure is on...
Donde esta la parte del vídeo donde cambias los sellos del eje del pedal....
@latexihire
Жыл бұрын
I didn't change those gaskets, it didn't leak.
I got oil leak forminside of cabin and need to remove the pedal part how
@latexihire
Жыл бұрын
In my own car Power Brake Booster Pedal holder clip -> www.joeldare.com/wiki/removing_the_power_brake_booster_pedal_clip
the seals aren't the right size for most of them unfortunately. I recommend getting in touch with a professional parts source.
@rosalindabatalla5988
2 ай бұрын
I got cheap ones from amazon and they worked well.
What kind of fluid do you put back in it? I filled mine up with power steering fluid. Is this correct?
@latexihire
Жыл бұрын
Yes, Power steering fluid.
@yeahrightbear8883
Жыл бұрын
@@latexihire thanks!
Do you have a link for the parts kit you bought?
@latexihire
5 ай бұрын
I have used this kit -> www.ebay.com/itm/143767565106?itmmeta=01HR6TS61KV0N13D64VDYV26Q4&hash=item217936f332:g:PmAAAOSwSP9bWiAz
I see that there are kits by different brands. Which one is good?
@latexihire
Жыл бұрын
I use universal seal repair kit-gm, ford, mopar
I have one problem you can only get seals by themselves online auto shops won't sell seals and mechanics upcharge way to much I can not order online and I don't have friends that'll let me use their addy to pick up parts I'm about to use my jobs address since they want to make life difficult for no reason
@alfredolara3144
Жыл бұрын
Amazon
I have watched several of these videos and no one changes the pedal rod seals. Is there a trick to these?
@latexihire
2 жыл бұрын
I only changed the important seals of the brake booster, not the seals of the pedal bar.
@arthurtirrell661
2 жыл бұрын
@@latexihire Mine is leaking.
@cameronyoung2124
Жыл бұрын
I've replaced 3 on my 13 duramax and every one has leaked into cab and one through weep hole on bottom of booster. Get a squishy pedal feel and squealy brakes
@bib4211
9 ай бұрын
You have to cut the eyelid off and after replacing the seals weld the eyelid back on ,or cut some threads on both sides and use a coupler nut to get it together for use in the truck
Is the pressure cylinder available?
@latexihire
8 ай бұрын
No information...
will this kit work for a 2009 chevrolet silverado 2500hd?
@latexihire
Жыл бұрын
No information on compatibility.
What is the torque or the housing ?
@latexihire
3 ай бұрын
Tightening approx. 25 Nm + Thread locking glue.
@blackerdenblack1
3 ай бұрын
@@latexihire thanks
Where did you purchase kit from?
@latexihire
6 ай бұрын
Ebay...
Where do you buy the gaskets set
@latexihire
Жыл бұрын
Ebay 👍
Is this a staked rod unit?
@latexihire
9 ай бұрын
No information.
Where can I get this kit
@latexihire
9 ай бұрын
I ordered on ebay...
The diagram shows a ball bearing between the two components of the accumulator valve (the yellow piece and the piece with the pin in it), yet your unit had NO such ball bearing. Further, video kzread.info/dash/bejne/hp2HtZR_ZdK3hZM.html blames the failure of his unit on the omission of the ball bearing. Do you know what the story is with the ball bearing?
@latexihire
9 ай бұрын
No information about that ball bearing.
What about leaks on the outer cylindrical tube?
@latexihire
Жыл бұрын
No information about that leak.
@mayken6661
Жыл бұрын
You sure it’s not leaking down from This spot ? It’s what mine is doing now
Where did you get parts at
@latexihire
2 жыл бұрын
I ordered on ebay.
Sir good pm order sana ako nang kit.ford550 2013 model
@latexihire
3 ай бұрын
I have no information
would you guys rebuild a booster if yes how much
@blkjazz
2 жыл бұрын
and a price and a email
@latexihire
2 жыл бұрын
This is a garage hobby, not a professional repair.
Como eu faço pra comprar esse kit de reparos, você vende ??
@latexihire
Жыл бұрын
For example ebay.
@juanpablojuan8294
Жыл бұрын
@@latexihire podrías pasarme un línk de Ebay para poder comprarlo? Saludos de Uruguay
@juanpablojuan8294
Жыл бұрын
Año 1972
what was the size of the first seal you pulled out?
@latexihire
Жыл бұрын
No memory, thats seal...
@jonathanch683
Жыл бұрын
@@latexihire ?
what all yrs does that pretain too i have a 98 gmc 3500hd i got a new replacement part and it all ready has that in it so do i still take out my old one and put in the new part even it all ready has one,,,,im curious
@ieatfoodthatisgood
9 ай бұрын
They are supposedly universal.