Removal, Disassembly And Inspection GM 246 Transfer Case from a 2004 Chevrolet Suburban Z71. BE SURE TO WATCH OUR PART 1 AND 2 FOR RE ASSEMBLY
Жүктеу.....
Пікірлер: 10
@starvethebeast6480 Жыл бұрын
Mine was leaking in that exact same spot. I scrubbed it with a wire brush and engine degreaser, then patched it with JB weld, right in place, no disassembly necessary. been holding for almost a month now, not one drop. It took like 20 minutes to clean and patch. The hardest part was finding the leak.
@Ryanfantana Жыл бұрын
The pump on the np246gm transfer case will wear 3 pin holes, the 4th pump tab is in a thicker spot on the housing. You will hopefully notice the oil spots on the tailgate or hatch of your truck or suv before it grenades. A quick “road trip” fix is to clean the spots with a wire wheel and brake cleaner then apply a tube of permatex ultra gray over the outside of the 3 holes in the rear case half and viola’ temporary permanent fix… use jb weld quick steel if you don’t have time for the permatex to cure.
@TomAutoTV
Жыл бұрын
We have seen a few with JB Weld. We caught this one before a road trip to Texas. Thanks For Watching
@OfficialTonyThaBoss7 ай бұрын
Thank you so much for this video
@ChasingtheWildWonder2 жыл бұрын
Watch out, boy, she'll chew you up!
@lt1nut
2 жыл бұрын
Welcome to the power of the hoo-hoo and zewbies! (As if we all don't already know that.)
@C6903 Жыл бұрын
5:00 what is that saver?
@TomAutoTV
Жыл бұрын
That was the original. I use the Case saver from Adapt A Case BRNY is the part #. Thanks For Watching
@C6903
Жыл бұрын
@@TomAutoTV thanks for the fast response
@c.s.i.s62846 ай бұрын
Hey Tom I recently took apart a NVG-136 from a 2005 Chevy Astro and I was wondering how the oil pump works? I see the internal splines and I'm guess the oil is suctioned from the sump and send to places where its needed but I'm not sure how the oil gets there. I was wondering if you could explain how the oil gets from the pump to the places that need lubrication thanks.
Пікірлер: 10
Mine was leaking in that exact same spot. I scrubbed it with a wire brush and engine degreaser, then patched it with JB weld, right in place, no disassembly necessary. been holding for almost a month now, not one drop. It took like 20 minutes to clean and patch. The hardest part was finding the leak.
The pump on the np246gm transfer case will wear 3 pin holes, the 4th pump tab is in a thicker spot on the housing. You will hopefully notice the oil spots on the tailgate or hatch of your truck or suv before it grenades. A quick “road trip” fix is to clean the spots with a wire wheel and brake cleaner then apply a tube of permatex ultra gray over the outside of the 3 holes in the rear case half and viola’ temporary permanent fix… use jb weld quick steel if you don’t have time for the permatex to cure.
@TomAutoTV
Жыл бұрын
We have seen a few with JB Weld. We caught this one before a road trip to Texas. Thanks For Watching
Thank you so much for this video
Watch out, boy, she'll chew you up!
@lt1nut
2 жыл бұрын
Welcome to the power of the hoo-hoo and zewbies! (As if we all don't already know that.)
5:00 what is that saver?
@TomAutoTV
Жыл бұрын
That was the original. I use the Case saver from Adapt A Case BRNY is the part #. Thanks For Watching
@C6903
Жыл бұрын
@@TomAutoTV thanks for the fast response
Hey Tom I recently took apart a NVG-136 from a 2005 Chevy Astro and I was wondering how the oil pump works? I see the internal splines and I'm guess the oil is suctioned from the sump and send to places where its needed but I'm not sure how the oil gets there. I was wondering if you could explain how the oil gets from the pump to the places that need lubrication thanks.