Get this External Sub Gz Antenna for the FlipperZero
This little Signal Booster dev board add-on for Dark Flippers is a must-buy for Flipper users.
If you want to give your #FlipperZero a significant Sub GHz signal boost, get this external sub-GHz GPIO dev board antenna. You can find it here on Amazon for $35.99 a.co/d/gOTwZdS #flipperzero #hacking #flipperzerotutorials #ghostexodus #ghostexoduseta
Пікірлер: 184
Being able to scan radio signals is basically the whole reason I am wanting to get a flipper. Is it possible to get an external board that does different frequency ranges? I want to be able to receive in the 150MHz band. I have seen other chips that come on boards that do this range but I am unsure whether or not the flipper will do it. I also do not care about being able to transmit on these frequencies just monitor them for noise issues.
@Zubbbz
11 ай бұрын
get a software defined radio if this is something you want to do. I guarentee you will be much happier
@MyriadDubstep
10 ай бұрын
Flipper pairs well with the HackRF One
@rustyfisher2081
9 ай бұрын
like @Zubbbz said, just get something that's specifically made for radio signals. a flipper is a multitool, it does a lot of things, can do them decently, but a specific tool for a specific purpose will surpass it
@hanfo420
8 ай бұрын
@@rustyfisher2081most of the things flipper can do are toys, not serious hacking etc. so yeah hack rf one is the choice
So this does not extend the signal to receive car keys from further away
If you’re running third party firmware having this module is a MUST!! I can’t stress this enough.. My brother torched his flippers CC1101.. Fried it.. Don’t be like him 🤣
@ClickClack_Bam
Жыл бұрын
How did he fry his Flipper Zero ?
@Thadopeera
Жыл бұрын
@@ClickClack_Bam using subghz without cc1101 module.. Jamming..
@ClickClack_Bam
Жыл бұрын
@@Thadopeera So it fried from him using it steadily? What do you think the antennae does to stop this from frying? I'm learning about all this so I appreciate your input.
@elissitdesign
Жыл бұрын
Probably left the 5volts active. Turn it off when you don’t have a module plugged in. Those ports are vulnerable.
@niFeforever
10 ай бұрын
Or he did what is written not to do in the CFW instructions - do not extend SubGhz frequency range without proper hardware. This is disabled by default in the CFW and can only be enabled by going deep into the settings.
Where can you buy one of these?
Would this work with jamming codes and increase their range? Also I'm writing my own code for raido frequencies, will this alow me to use my flipper like a walkie-talkie/radio? If so could I get the link?
@ian22341c
Жыл бұрын
yes im pretty sure you can extend jamming range idk about using it as a walkie talkie tho
@Dylan-qi4pd
Жыл бұрын
if youre talking about subghz jamming then yes it would increase the range as it increases the strength of the subghz signal that jams others
Where can I get one? Same place I got my flipper?
Maybe you can give me some guildance I tried to Preset the flipper while I await for the antenna to arrive, I toggeled on the GPIO and went over to Sub- Gig....I do not have Radio settings on the drop down list it goes from Frequency Analyzer to Test. Is that because I do not have an antenna in the flipper or is there some flaw in the Murader Firmware?
@ghostexodus
Жыл бұрын
There is an internal antenna, the range is limited, but it is completely functional and practical. He will not be able to use GPIO functions until you obtain a GPIO dev board. May I ask, what firmware are you using?
@Index-o1234
Жыл бұрын
@@ghostexodus I am using Murader but now am confused with your reply because I was able to go into the GPIO setting and turn it on.....Am I missing something? A program? An additional Board?
HI, I have xtreme firmware, if I set 5V ON on GPIO, then I go to SUBGHZ / Saveed and try to transmit a saved renote controller pattern, next time I go back to GPIO I find 5 volt gone back to OFF, in fact I see no improvement compared to the built-in antenna in terms of transmitting range, How is it possible to set 5v to ON permanently? thanks
@ghostexodus
2 ай бұрын
From everything I’ve seen online, everyone similarly situated reports that you must turn the 5 volt back to ON each time you use it. There does not appear to be a permanent fix to this. This might be an interesting suggestion to the developers.
Uh, sorry. I think I walked into the wrong classroom.
@ItIsSpade
Жыл бұрын
Well now you're not allowed to leave
@xfirehurican
Жыл бұрын
@@ItIsSpade 🤣
@thebusinesscentre
Жыл бұрын
No ur good here 😂
@franticpanic4036
11 ай бұрын
Nice likes
@properdukes9091
11 ай бұрын
But don’t mind me, I’ll just grab a seat and y’all just pretend I’m not here.
How did you get yours to have the layout that you had when you first get it turned on.
@kiriltrenkoski
6 ай бұрын
RougeMaster software
Thank you
going to have to look into the dark flipper firmwares.
@monkeyrhythm
Жыл бұрын
You find anything?
@an0nud4y26
11 ай бұрын
Probably referring to Xtreme Firmware for flipper zero
@guitailang4189
8 ай бұрын
Xtreme Firmware
@TSOP2020
5 ай бұрын
xtreme is great can confirm just threw it on mine today. 3/8/2024
I'll have to check out this antennae!
I have this antenna, however, when i turn 5v on in gpio, it immediately turns back off as soon as i enter into the subghz menu. I can use the antenna for jamming, but nothing else. When i turn on external module in subghz, i also turn on 5v.. however like o said, 5v will not stay on in gpio... cannot figure it out.
@danielm9615
Жыл бұрын
There's no need for 5V when using the external one. The 5V pin in some of these external antennas are touching the antenna itself. You can cut the end of the pin that's touching the antenna (If it's touching it) and plug it in. Then I don't think you need to turn 5v on
@530jm
28 күн бұрын
You have the solution i have the same problème
@triple9finestacker631
27 күн бұрын
@@530jm yea, supposedly this antenna does not utilize the 5v port, therefore 5v is not necessary, this has been what i was told. i purchased a different extender from rabbit labs that works perfectly.
What firmware version so you have to have the new Application layout. I want that!
@biscuit2752
Жыл бұрын
Xtreme firmware by Clara crazy it is a setting that is turned off by default
@ianbos3581
Жыл бұрын
@@biscuit2752 you mean turned on because when i installed xtreme on my flipper it was already like this
What is the point of a cc1101?
So hypothetically let’s say I was pointing my flipper at a Tesla. From 20-30ft as an example. Would I wanna set the Rssi to be more restrictive/precise? dose that decrease my transmission range as well? I apologize if these are stupid questions. Edit: Im using this gpio antenna set-up
@danielm9615
Жыл бұрын
If your goal is to be able to mess with the Tesla from far away by sending signals then the RSSI threshold shouldn't be something you have to worry about. As long as you have the right signal then you're good. But let's say you want to pick up a signal from something that is close to you you would need to set the threshold to be alot stronger, and vice versa. Also not entirely sure what you mean by your question
@ghostexodus
Жыл бұрын
Adjust the RSSI sensitivity to the right. That way it won’t receive signals you’re not trying to receive. How’s it working for you btw?
@JBS_IT
Жыл бұрын
@@ghostexodus Thanks for the response man! Everything has been working great so far, really neat little antenna set up. Been running some rolling codes from my house to open/close the garage door
@NicoArias
4 ай бұрын
Hey I’m looking to get a flipper zero I have it ready to order but I’m still unsure if the flipper zero is worth it. What can I actually use it for in the real world without causing any big trouble?
@JBS_IT
4 ай бұрын
@@NicoArias I've grown in the CS department since my last comment, and I would say it's worthwhile if you like experimenting. The more you understand about IT and computer science the more useful it becomes as both a tool and a toy as well. As far as getting in trouble it depends on what you do with it, if you write mal-indented scripts to steal passwords without permission, you could get in trouble. If you run programs to de-auth wifi or create fake portals for mal-intended purposes, you could get in trouble. Play wisely. Best to treat it as a means of learning.
The amazon link is out of stock, anywhere else we can get this external antenna?
@svagoio
Ай бұрын
Bro just build It It simple
Link to order?
Whre can i buy it
im making my own😅 exacly same
Ok.. sod it.. I wanted a Flipper but I really want one now.
just got mine, cant get it to seat properly because of the silicone case. anyone know of there is a extension cable?
@MamaMia84oo7
3 ай бұрын
Why don’t you cut the silicone?
Could you please go into the sub-GHz menu and go all the way down to test and test it with the antenna and reply and tell me the dBm? I am still deciding if I should get one or something else.
@ghostexodus
Жыл бұрын
I can do that. I’m not by my antenna atm. However, if you go to my website, you can contact me directly. Drop the best way to reach you in a message and I’ll do that.
@flamelightningbird6532
Жыл бұрын
@@ghostexodus Thank you. I may do that if I am still interested, but I am now looking at just spending like $10 for the EBYTE cc1101 module and a 2.5 dbi antenna and some dupont wires.
🤔👉Any other place to get it but Amazon??
I have the same one but it doesn't fit with case did you find a solution to keep it stuck with the case?
@ghostexodus
3 ай бұрын
That sucks, yours doesn't seem to be sitting flush against your rubber casing. I didn't modify mine. Does it sit flush if you remove the casing? If it does, you might try to modify the casing and see if thta helps.
@hamadyousef4368
3 ай бұрын
@@ghostexodus it works only if I hold it down I will buy a new case to modify it 👍
whats the link
Thanks Brother, us Magickians need to stick together.
Why doesnt it work on the stock firmware? Seems to work fine on mine?
@ghostexodus
7 ай бұрын
I did a little digging on this. There was a time when then Sub Ghz antenna was not supported by stock firmware, but is supposed to be fixed in upcoming releases. If anyone is experiencing issues using the stock firmware, you know its time to "upgrade" Unleased or any other dark flipper firmware.
what if yours doesn't have radio settings
Does it also increase jamming range signals ?
@ghostexodus
2 ай бұрын
Why yes. Yes, it does.
How did you get a flipper in the US I’d like to buy one but they don’t ship from website. Also don’t want to overpay obviously
@atherlie5870
Жыл бұрын
@@xxposed501 thanks for reply I feel like there are maybe still cheaper options maybe I’m wrong
@alexjones9308
Жыл бұрын
I just got one from the official website.
@atherlie5870
Жыл бұрын
@@alexjones9308 same now that I tried again. Guess they’ll ship now sweet
@ghostexodus
Жыл бұрын
This was sold on Amazon until Amazon pulled the product. It was marked up, pretty pricey there, and any third-party website is going to market up because of the high demand. Unfortunately, the best way to get it is through the website, itself, or somewhere nice enough not to try to make a buck off of you, selling theirs.
@RealNikoBellic
Жыл бұрын
I just received mine today. I ordered it from their website directly, took about 2 weeks to arrive.
Dr. FuzzyKnuckles, is that you? I think it's time for another prostate exam. After watching this video, i may need to seek another opinion.
will this make it so u scan rfid from farther away
hello, please give me a link. i wóld buy it. Big thanks.
I think my got i problem when i go to radio settings i dont have the options ext radio 5v or debug pin or counter inccr i only have module external ddo youuu have a fix
@ghostexodus
2 ай бұрын
I wonder if that is a firmware issue. I’m not certain, but perhaps there is a Reddit on this very issue you are experiencing
@LcpdfrTutorials
2 ай бұрын
@@ghostexodus i mean i use the normal flipperzero firmware
What firmware are you running?
@1mpulse182
Жыл бұрын
Xtreme
Link to purchase please or put up your GPIO schematic.
@AdainClark
13 күн бұрын
External CC1101 Antenna for Flipper Zero
@thereaper489
13 күн бұрын
@@AdainClark no worries. Ive built more than that for the flipper since this comment. Thanks tho.
can you post a link cant find it
Where can I buy the cable to connect to iPhone & flipper zero @ the same time, any links please 🙏 cheers ✌️ ❤
Ciao dove trovo un antenna
I dont even see external or test in my radio settings......I tried xtreme and unleashed and it only says internal with no option to change it...Any suggestions????
@burnrobe69
4 ай бұрын
You might have to plug the module in.. mine does it automatically
why wont this be able to work with the stock firmware?
@RedShirtMenace808
2 ай бұрын
legality
Do you have an affiliate link?
@ghostexodus
Жыл бұрын
Not really. BUt here's the product on Amazon. www.amazon.com/dp/B0BY1WVHG2?ref_=cm_sw_r_apin_dp_ZFC7XWQPXC9GDQ7DQ3AY
@cryogeniccrysis4765
Жыл бұрын
I would immediately do that lol. Super easy. Will take you 5 ish min
@bign1667
Жыл бұрын
@@ghostexodusshame it can't be shipped to Australia
@fidedavalos
Жыл бұрын
@@bign1667 ship it to my house and I’ll ship it to you. I’m in the US. 😎
@djfunny007
Жыл бұрын
@@ghostexodusIt cannot be shipped to UK
Oh boy just walked in to the HACKER ROOM
@peaceformula5830
Жыл бұрын
Is this guy the famous Four Chan?
@mrwhitefolks1211
Жыл бұрын
@peaceformula5830 ahhh can't talk in here
Is this unleashed firmware?
@ghostexodus
Жыл бұрын
I was using Xtreme firmware in this video. However, I decided to switch back to Unleashed simply because the other was lacking Bad USB functions.
This Russian Jammer, is it also used to block 3g signal up to 5g momentarily? Can I also fool the ultrasonic audio suppressor my neighbors have? I can understand that they are talking, I can understand something even if from very far away and then I can feel the vibrations of this "toy" instrument that doesn't even work well. For me it is a real torment especially during the night hours. I need it to play a joke on my neighbors. :) OK!!! Let me know. Thank you. Bye.
@iyeetsecurity922
2 ай бұрын
It's not a jammer.
Can it be made to work with the Xtreme firmware?
@niklaskarossa2750
Жыл бұрын
i think he uses the extreme Firmware because of the layout you see
@izan4785
Жыл бұрын
Yes, Xtreme, Unleashed and Roguemaster
Where would one find this dark firmware?
Why are things so expensive in america? I see so many dev board and ir booster and antenna sold online in my country for $3-$5. It's mostly for highschool classroom that teach IoT and electronic class.
@ghostexodus
Жыл бұрын
Capitolism, friend. That, and scarcity. The price of the FlipperZero itself has raised exponentially because of demand. The developers know users will be willing to pay more than what it costs the build a unit. :(
@plzzz
Жыл бұрын
@@ghostexodus well to be fair, I did pay $320 for my flipper zero and it was the cheap I can get locally without having to wait 3 weeks.
Dude! Make more videos.
dude use a camera stand!
This guy's communication skills ...
@ghostexodus
Жыл бұрын
¯\_(ツ)_/¯
Go out and test it pls😢
Swallowing sounds ASMR
Where get this from!!!???? XD
That is not antenna, the transceiver itself
@ghostexodus
Жыл бұрын
Thank you for offering that clarification :)
@Kholaslittlespot1
Жыл бұрын
I mean, it clearly has an antenna also?
@RandoWisLuL
9 ай бұрын
@@Kholaslittlespot1 yes but its a transceiver that can take multiple antennas
Imagine paying $36 for a $4-9 radio chip. All because someone wired it for you.
@cpt_Ruckus
Жыл бұрын
Imagine having a zero value for your own time like this guy.
@kmoney604
Жыл бұрын
I just realized that earlier today with the nrf24. What is this one called?
@kmoney604
Жыл бұрын
Cancel that cancel that i got it
This does not work
@ghostexodus
5 ай бұрын
What issue are you having? Also, read through some of these comments, I think they are quite useful.
@donimperioli5328
5 ай бұрын
hey man I'm having a big problem when i turn on the 5v gpio and i got to the sub-ghz the 5v turn off and the external wont come up as an option on the radio settings I have tried to change software from rouge to xtream haven't tried unleased I will soon any tips on a solution @@ghostexodus
Love how you tell us to get the antenna yet dont tell us what the name of it is or where to get it
@239seth
Жыл бұрын
Did you not watch the first 15 seconds lmfao your don’t deserve it anyway.
@ghostexodus
Жыл бұрын
"Sub ghz radio antenna that you can get on Amazon for $35.99" a.co/d/gOTwZdS
@Cosmic_Corp
Жыл бұрын
Literally 12 seconds into the video chief
@francisalba4773
5 ай бұрын
Fr he said it and on Amazon
@billlewsey7961
5 ай бұрын
Do you need a hug?
Youve just made your flipper vulnerable to having its front end blown out by adding an external antenna. 430 to 440 mhz is used by high powered ham transceivers.
@gaddyfree1085
Жыл бұрын
Yikes
@flightstatic4662
Жыл бұрын
everyone gansta till they drive by someone doing 1.5kw on 70cm
@cameltoast
Жыл бұрын
@@flightstatic4662Lol HAM shit talk
@user-oe6iz5gs5k
Жыл бұрын
lololol bro..... no
@grass5496
Жыл бұрын
but if he switched from using internal to external wouldnt internal not be powered?
I think you want show. No need teach. 😂😂
Stop saying, “uhmm”.
I CAN'T for the life of me understand what he's saying at about :49 seconds with what this antennae works with & what it doesn't. Is he saying this antennae DOESN'T work with the normal Flipper Zero software that you'll use but it works with EVERYTHING else?
@Jonnyweareten
Жыл бұрын
he says it will only work with dark flipper firmware, not the default firmware
@productisright
Жыл бұрын
Basically what’s needed to be unlocked to use this device isn’t enabled in default firmware so you will need to install a darkflipper custom firmware or any custom firmware will likely work
@kciwner
Жыл бұрын
Will work with Flipper Extreme firmware as well. But what I can’t figure out is about 11 seconds in to video. How did the back of this guys hands get so hairy?
@Jonnyweareten
Жыл бұрын
@@kciwner the sub gz antenna also boosts hair growth.
blablablablablabla
it is fake, yes doorbell will copy, but the car signal well copy too but to replay the signal it wont open. it is fake, not recommended to buy. fake useless. lot fake video on youtub be aware not copy cards or any worth in your way.
@kevinmichaels3281
3 ай бұрын
The car and your doorbell probably use rolling codes.the car definitely does so not fake it's just the security is better then u thought
Can you jam Bluetooth signals with a flipper zero?
@banana-drank5835
Жыл бұрын
No
@RapeUAsDiddy
Жыл бұрын
@@banana-drank5835 thank you. Is it possible to jam a Bluetooth signal?
@mildanmauliadi
Жыл бұрын
@Tin Man I think he's asking "without flip"
@sethwilson7850
Жыл бұрын
You can Jam certain signals, yet not with the base flipper, yet a 'Dark' modification of the Flipper Software