Thank you for sharing your experience about gen set troubleshooting my dear friend

@DieselGeneratortraining

Жыл бұрын

Ur welcome

Thanks very much,i wish this teaching should go with a video sir,so can know the relay and fuses controlling the solenoid

Sir pcc module ki viedo banye

Model 1506A perkins generator 250 kva there is also ECU crank but not starting what the problem?

Good job 👍

How to check fuel relay fuel selonoid practically ?

Thanks 👍

Thank you my friend watching from isarael

@DieselGeneratortraining

Жыл бұрын

Thank you too

Super explained sir thq

@DieselGeneratortraining

Жыл бұрын

Thanks

I had 6010 controller with fail to stop alarm . I change 3 vdo10 bar oil pressure sensor but still the same condition... suddenly it fail to stop gone and then I can run it. After 5 second again stop and show stopping and cannot be reset . After timer goes out I had fail to stop again .... what shall I do?

Thank you my friend...

@DieselGeneratortraining

Жыл бұрын

Ur welcome

Mebay 25kva sir they change after that start is o.k but a few second will off.what is the problem sir thanks

That's my problem my friend i hope you give some tips for me to fix my problem thanks

Hi sir , what happens if the generator is starting via a relay and through a direct wire but does not run on its own it requires one to hold accelerator and once you let go of the accelerator it then switch itself off. I also get the fail to stop alarm. The generator doesn't not start via the control panel. . Where should I start checking? Thank you

THE generator show governer alar it is not startes when i make start will near to start and then will stop, what i will do?

@DieselGeneratortraining

6 ай бұрын

What is the model of Generators

Thank you very much 🥰 Why "failed to stop " is related to oil pressure sensor instead of the Solenoid,?

@DieselGeneratortraining

Жыл бұрын

Great point!

@alastairwaters9114

10 ай бұрын

Majority of generator controllers use the oil pressure switch to detect if engine is running, so if you have faulty oil pressure switch then the controller might expect to see that switch open when we shut off engine but if its closed then the controller is still thinking that engine is running. Simple

Sir our Smartgen operating or ranking start fiw time quickly buzzer alarm coming & outermatic generator stop how check sir i need instructions thanks

While changing oil filter,is a must to fill it with oil before installation just like fuel filters?

Hi, if engine failed to start so more chaces of MPU not sence the RPM and air trapped in fuel.

@DieselGeneratortraining

Жыл бұрын

Many aspects

Sir i have problem my generator start to fail then i direct the solinoid it its running i change the realy then start running not also running

@DieselGeneratortraining

Жыл бұрын

U need expert inspection

Dear sir,In emergency how we can bypass oil pressure sensor..

@alastairwaters9114

10 ай бұрын

You shouldn't have to by pass it? Depends what controller you have but when cranking remove the oil switch wire and that should by pass it but you shouldn't bypass it unless you want to see metal lol

your dg why dish pley sow the. run feedback fail. please really caterpillar have DG. 500 kV

@DieselGeneratortraining

Жыл бұрын

Which engine C18 and which controller type

😅😅😅😅😅

@DieselGeneratortraining

Жыл бұрын

😁😁😁😁😁

Actuator not working that's why engine fail to start connection is not normally works

Failed to start, low oil pressure light indicated

Sir guidelines chaiye

@DieselGeneratortraining

Жыл бұрын

Send your inquires on Info.powerlearning@gmail.com

pls make in ATS foult video

@DieselGeneratortraining

Жыл бұрын

Ok noted always comment what u want to learn about