May I say this is the best garage door opener tutorial on all KZread!

Great video. Considering the replacement of my vintage 1990's Liftmaster and this was a nice replacement walk-through. I just bought my replacement opener and watched this video again. My only "old guy" advice would be to hand start bolts you're installing, rather than starting them with the ratchet. Helps you avoid cross-threading things.

I installed this exact garage door opener today. Thanks a ton for your guide, it was very helpful!

Nice timing. My garage door opener stopped listening to all its remotes so I'm shopping for a new one. I didn't know they made them with battery backups.

Very well done, consider shortening the bare wire when connecting to the unit to prevent short circuits if the wire ever gets accidentally pulled.

Hey, thanks to your video I just saved myself $900 by doing it myself. Thank you!

GREAT call out for the extension. I almost bought a kit and assumed plug and play. Saved me from turning back around and going to Lowes.

@HaggaiTembo-fr9xb

Жыл бұрын

Thanks

Awesome thank you! Can you consider doing a vid adjusting the garage door and reducing some gaps?

Just did it solo, was very easy! Thanks!

Thank you for the lesson . Keep doing these videos so we could learn from you. Thank you…

This vid was awesome thanks. Did the whole installation watching this. It made it so simple thank you. 🤙🤙🤙🤙

Good job. Thanks for sharing saved for the future

Thanks a lot for sharing. You saved me $$$

Great video I have had seen couple of your how to videos that were also amazing. But question to you is I have a genie garage opener. It also uses a rubber belt too but you can't add a backup battery to it. So do you think it I take a short cut by just. Changing the motor and hook it up the existing rail and belt and just reprogram everything else. Your expertise would surely appreciated. Thank You.

Very clear demonstration p

An excellent job!

Thanks bud for this

Just what I needed

Really good video!

Did your unit come with the belt retainer piece of plastic? I noticed mine didn't, I have 7155-TKVE (from Lowes) also a belt driven model, but don't see that piece. I noticed in your video you never covered that piece so I never really thought of it. However I see other videos and they cover this piece.

Well done!

Great amazing informative video I give it a 100 and plus

Great explanation! thankyou. :)

Greetings, I cleaned sensors, bought two new different remotes, erased all memory... indoor button works fine all the time. Both new remotes must be pressed several times or it works on the first time and then not. Wires seem to be fine even when I wiggle them sensors do not flicker. How can I trouble shoot the geniue motor? Installed 2004. Thank you.

Awesome! Another skill I needed to learn, thank you! 💥👍🏻☺️

Good video 👍

Awesome video

Good job.

Did you lock the part over the turnbuckle before trying it?

I have the opener up , but can’t get the turn buckle closer to the door to install the arm. The belt won’t move. Any ideas?

@16:04 is your right most sensor wire shorting to the case?

Nice one man

Anyone have any ideas why my opener not moving when I jump the white n red ? This is preventing me to install this wireless opener

How do I fix the rail/track since after 30 yrs it’s now cutting into the top of the garage door when opens

I had to replace the rollers on my garage door because of wear. If yours is old that might make it quieter and prolong the life of your garage door opener/motor.

@LRN2DIY

3 жыл бұрын

Good point - that's probably a fairly inexpensive way to maintain things and quiet it down. We actually had made so many adjustments to my mother-in-law's garage door system that I researched replacing EVERYTHING - door, motor, track, spring, electronics, etc. and it was at least $2000 if I went pretty basic and did it all myself so anything you can do to keep things rolling is worthwhile.

great video! I have a marantec 4700, I want to replace it with another brand. do all garage door opener harnesses the same?

@LRN2DIY

2 жыл бұрын

If you're referring to the way they mount, that definitely differs but you can usually work it out with what's there. For the wiring, there are typically just the sensors for the safety beams plus the main button pad, so those are pretty universal.

@harbinguy1

2 жыл бұрын

@@LRN2DIY Thanks! I mean mounting brackets.

I am planning to install a security camera in front of my garage. Is it safe to drill a hole through that solid wood in the middle above the spring?

@LRN2DIY

2 жыл бұрын

As long as it's a small hole (presumably for passing a wire through?) then that shouldn't be a problem.

@cdpc211

2 жыл бұрын

@@LRN2DIY yes for passing a wire through. Thanks.

Do you need to turn off electricity or is it safe to connect the wires

Hi

Your garage door looks like it was heated up by an extreme amount of heat.

You really covered the code. LOL

Good explanation for everything. Should make things go a little smoother. Lol. Drove me a little nuts on the pronunciation of clevis, though. It's not cleavis. Sorry, I couldn't help myself 😂

Bruh that crack in your ceiling 😰

Pronounced clea-vise not clee-vise

@Brody1007

Жыл бұрын

Klev-is

@onemansyn

Жыл бұрын

@@Brody1007 😂

Genie junk

Backpack, person...woman, man, camera, TV.