Full restoration of old 220v generator engine | Repair and reuse old rusty generators
Жүктеу.....
Пікірлер: 333
@ErniefromhCanada9 ай бұрын
Vietnamese miracle. It even works without fuel. The engine shutdown switch is not connected either.
@ArmandPedroza
5 ай бұрын
I noticed too, the engine ran without gasoline.
@BobSmith-eq9vs Жыл бұрын
The frame on the original find was rusted completely through. Miraculously it was fine later.
@elliswatkins812 Жыл бұрын
That generator is not running right at all you shouldn’t need a second person to rev the engine up when you apply a load to it
@anthonielegrange8688
8 ай бұрын
Just need to adjust the governor for the revs
@burriedhistory Жыл бұрын
Awesome. This video made me remember my father repairing all sorts of engines and cars. Thank you.
@MrSanmanbob Жыл бұрын
nice work, now you have a generator for power when you need it.
@tomboman2 жыл бұрын
Always love it when people spray something like WD40 on a bolt, and then after 2 seconds try to loosen it.
@eliecermora76482 жыл бұрын
Quedó nuevecito, que buena restauración.👍👋🇨🇴
@thewaronthewest.9262 жыл бұрын
Great video buddy. You have to be very careful mounting the generator end casing on & even more so the Brush set. Very careful indeed.
@chuckvenable4409 Жыл бұрын
I've got the same exact generator without all the rust and mess. It helps keeping it out of the elements when not in use.
@felixcat93182 жыл бұрын
Not at all keen on setting the bearings that way, nor the complete absence of a torque wrench! Adjusting the tappets would be preferable, as would setting the bearings on the outer raceway, preferably with something softer than steel. Nice to see the youngster participating with his father to learn skills. The generator appreciated some care and attention after being abandoned, and I was surprised that all the fasteners unscrewed intact! All in all a nice restoration, with some finesse it would have been great. Subscribed.
@Skoda130
2 жыл бұрын
Some just need to work with the tools that they have at their disposal.
@misterv1472 жыл бұрын
Друг, вот ты рукастый мужик!
@bpetnoi14722 жыл бұрын
I know these guys are working with limited tools, but to beat the center of a bearing is just asking for a failure of that bearing.
@restoration-bq3921
2 жыл бұрын
thank you
@harshabiliangady32112 жыл бұрын
Considering where you found it I was expecting a baby cobra to come out. Since you stage so many finds it’s time you got yourself a workbench and torque wrench.
@Subgunman2 жыл бұрын
Great restoration with limited resources. Attention to detail by pre oiling most everything within the engine is great but use some wood blocks on the bearings the next time you need to set them in. This is the exact same gen set that Lidl has sold in the EU market, didn't realize it had an AVR module in it.
@restoration-bq3921
2 жыл бұрын
thank you very muck
@rezaramadhan6075
2 жыл бұрын
Lksnssn NK u.h N. Y
@user-yh1oq8ei5n
2 жыл бұрын
Рм? 0фх
@user-lm9sf6le5n
9 ай бұрын
❤❤❤❤❤
@bilaltechcity86132 жыл бұрын
Amazing Restoration...!
2 жыл бұрын
Có cái ghế sa lông ngày xưa đấy phục hồi lại xem nào 🤣
@mohd682 жыл бұрын
You are woooooow 👍🤔 Tanks boos بصراحه انت روعه 👍🤔
@user-ib4rs2ev1b Жыл бұрын
Я думал он его сейчас помоет с фери покрасит и все.с компами они же так делают и работают 😂😂😂
@expo199311 ай бұрын
Well done! 😊
@calvinhobbes75042 жыл бұрын
God bless you, sir .... that place looked like the perfect venue for a snakebite!!! Plus you set both valve springs by hand. I would have received a cut thumb, gotten popped in the eye - or both.
@restoration-bq3921
2 жыл бұрын
thank you
@skhasibul4895
2 жыл бұрын
A
@hamdyhayba36972 жыл бұрын
the spray paint not resist the gasolin ..i suggest useing sandblaster to clean aluminum parts ..and you must replace all gaskets and not use hammer to assemble the stator base because the camshaft may be break it .. good jop brother ..
@csimone1986 Жыл бұрын
You forgot to put the long screw that holds generator to motor crankshaft
@mohamed-fahod_9902 жыл бұрын
رائع للغاية قناة مفيدة جدا .
@reedthomas1087 Жыл бұрын
Beautiful repair. Loved how the new throttle spring was stretched out to fit lol but for real nice work.
@MichaudDanielАй бұрын
It's hard to believe it works!
@kassidyjones17610 ай бұрын
Easy assembly of legs n wheels. Now charging battery, will try to start it in morning.
@manae372 жыл бұрын
You did a great job and your work is so beautiful
@melvicaraneta30214 ай бұрын
salamat bro.detalyado Ang iyong demo...God bless.
@SanDiego_VDubLife2 жыл бұрын
Think of all the excuses we make here in America when it comes to not having the right tools or equipment. This dude went at it with what he had available and he got that thing running again. Even in his country where most folks would not even think about saving that thing. When you have nothing I guess you gotta make do. These videos inspire not to be such a woose and just go for it. We have everything and more in this country to do the job. Now back to procrastinating on fixing my projects outside. Jaaa
@dulatip2190
2 жыл бұрын
D
@jamescraig5421 Жыл бұрын
A totally new Lease on Life Bro. Beautiful restoration you just keep up the great work you are doing and I'll keep watching you and enjoying every minute of your shows .
@gurmanaulakah2 жыл бұрын
Respect 🙏. India 🇮🇳
@user-vd2tg8ms6i2 жыл бұрын
عراقي 🇮🇶مر من هنا
@user-qp2cp3oh3i2 жыл бұрын
Доктор Дью по тебе плачет горькими слезами
@Mikesorrento33442 жыл бұрын
Very nice job.
@akpexplorer79402 жыл бұрын
It is more like cleaning rather than restoration 😅
@tinytonymaloney78322 жыл бұрын
I take my hat off to the patience and memory of this guy, I would have just left the thing to rot and buy a new genny, I couldn't remember where all the bits went. Not keen on the method of fitting that bearing, should be fitted using force on the outer rim not inner.
@qaziqalander2 жыл бұрын
Great, Very good step by step restoration effort, yet practically simple enough to follow and help people with similar difficult situations, Thanks again
@restoration-bq3921
2 жыл бұрын
thankn you
@GiuseppeGibilmanno10 ай бұрын
you not show when put rear long bolt that keep elwctric rotor and engine shaft together 🤔😂
@a.malsaadoon17122 жыл бұрын
Great job..... but you put ( camshaft ) wrong.... Thanks with my best wishes.....
@MawarniStudio2 жыл бұрын
a very extraordinary restoration from a condition that is no longer feasible to be an item that is fit for use & sale. cool
@zafarfarhan4282 жыл бұрын
Wah g wah in Urdu Excellent" in English
@MarcioCostacantor2 жыл бұрын
Bom dia! Pra mim é uma honra viu prestigiar seu trabalho, vamos sempre juntos somar e fortalecer nossos objetivos, Conto com você, eu já estou por aqui.
@KUNA_PANDA_SATYASAI_DTH2 жыл бұрын
Excellent Great Brother 🙏🙏🙏🙏
@JoyDee33472 жыл бұрын
Wow good job bro
@cv.sahabatprima4677
2 жыл бұрын
Good job
@learningcurve36922 жыл бұрын
Great restoration........
@restoration-bq3921
2 жыл бұрын
thank you
@Farm_fab Жыл бұрын
It's never a good idea to reuse bearings. If they were worn before you did the repairs, they will still need replaced. Depending on how they were removed, they may be damaged.
@thierrypapion1237 Жыл бұрын
Excellent Video Great restoration What do you guys adjust your intake and exhaust valve in mm and what kind of Spark plug is used on the 196 cc engine. All trade make the same generator but it is modified to use propane APG 3535 cn
@ammiali99792 жыл бұрын
amazing restoration ! you are the shief .
@restoration-bq3921
2 жыл бұрын
thank you very muck
@thinguyen20952 жыл бұрын
Cam ráp sai củng chạy được hay thiệt
@sghunterr2 жыл бұрын
Thanks for the amzing video, may I know what is the type of silver paint you use for the Crankcase and engine body? Is it a regular spray paint or is it a type of paint that can stand high heat?
@Twizter682 жыл бұрын
Now THAT was one scungy unit to start with!
@user-gt8tw2hq9h Жыл бұрын
عمل جيد جدا يا رفاق
@user-hm9rp1cu7j
7 күн бұрын
بس نسى ما خلالها دهن ونفجر البستم بعد عمك
@maatiraouki9124 Жыл бұрын
Merci pour l’exercice
@benaman56062 жыл бұрын
This is just cleaning and refreshing not full restore
@LZ1SSA2 жыл бұрын
Ето това е майстор. Браво
@jailsonaraujo57662 жыл бұрын
I really enjoyed this kind of content, it's very interesting Da to learn a lot of the mechanics of these power generators just by watching their videos. congratulations on the great video 😊
@miodragtodorovic7924
2 жыл бұрын
Vlaške. Narodn. Nigre. I
@makshhdjd20832 жыл бұрын
خطأ كبير يرجع يخلي الكازكيت المستخدم 😑 لازم يخلي جديد حتى ما يطك الكازكيت وعندو اخطاء هواي بس يله احسنت التعمير
@otsechki_net9190 Жыл бұрын
ГРМ не выставлен,клапана не притерты ))))
@luigicristiani77092 жыл бұрын
Find everything ... you !!! but where do you go to look, in landfills, in garages or other public or private places?
@zamanfix Жыл бұрын
Nice Work!
@pcfnokia2732 жыл бұрын
Không thấy thay thế cái gì, hầu như vẫn để như cũ, chứng tỏ máy còn mới, chỉ để lâu ngày bụi bẩn thôi
@chaudoc692 жыл бұрын
Hay. Bạn ổ việt nam ? Nhìn đôi dép lào - nón cối là biết ngay !
@industrialmonk2 жыл бұрын
I have one problem with this on this type of generator the engine's are almost indestructible but the electricity generators always fail & mostly avr's then the windings on rotor & lastly the stator it would be better/ more helpful to show the electricity generator being repaired as that's the most likely to fail.
@GGigabiteM2 жыл бұрын
16:49 - Các dấu chấm trên bánh răng phải thẳng hàng nếu không động cơ sẽ không hoạt động bình thường.
@VLADIMIR-zk9ry2 жыл бұрын
Das ist fantastisch!
@user-qj4xz7ub1h2 жыл бұрын
Я бы один ,так резво поднять генератор не смог..!
@andreimoj61922 жыл бұрын
Я так в первом классе разбирал! Плохо!!!
@user-gn3bg1eo9h
2 жыл бұрын
ס--ּ
@abbasfadhil49562 жыл бұрын
انت فتحت القديم ونظفتة لكن مرجعت شديتة شديت بدالة جديد
@ailail-sx5st
2 жыл бұрын
زين شلون شتغلت بدون بانزين
@gulvbelegg_med_hakk13712 жыл бұрын
Sure need some adjusting, sounded horribly. They could have made it 100% complete before ending the video.
@rvarghese30622 жыл бұрын
Nice work 👍
@MechanicAvenue2 ай бұрын
Work Hard And Win The World 👍❤
@tpelton2 жыл бұрын
taking the stator apart is ballsy
@shumailkhan26622 жыл бұрын
Very good i really love it♥️
@restoration-bq3921
2 жыл бұрын
thank you
@sixrsi3501
2 жыл бұрын
@@restoration-bq3921 b W
@idk-kg3yl2 жыл бұрын
Respect bro🤙
@restoration-bq3921
2 жыл бұрын
thank you
@edupena5953
2 жыл бұрын
Respecto man
@aw7382 жыл бұрын
You can't just pull the rotor off the crankshaft that easy.
@ehaurader2640Ай бұрын
Cool a generator that runs on fresh oxygen
@ThuTran-yy5uc2 жыл бұрын
Tiêu đề tiếng anh ngt xem nhiêu hơn hã chú.
@hamoodykinggamingmy5gbmgo4792 жыл бұрын
ARE YOU FIXED GENERATOR ENGINE😱😱😱😂😂😂😍😍😍😍😍👍👍👍👍👍👍👍👍👍👍👍👍
@romeovidalrodriguez77542 жыл бұрын
hola Y acá estamos... Hey Buen Video
@RESTORATIONOFSCRAPMETAL3 жыл бұрын
Greetings, Cool project and Great job buddy as always like👍
@restoration-bq3921
3 жыл бұрын
thank you fou your
@user-cq8ok7hd5i2 жыл бұрын
هناك غلط بل تجميع المحرك وهوة برغي الارميجر ما شديتة
@user-el2wp4xf6k
2 жыл бұрын
هو بس البرغي 😹بس الواشرات مال الكابريته هو يمكن حته دهن مخاله🇮🇶
@grootkaroo97212 жыл бұрын
Nice job ,
@psvyme48paulh452 жыл бұрын
Wow so cool 👍 🙏🇬🇧
@restoration-bq3921
2 жыл бұрын
thank you
@aijazkhan45302 жыл бұрын
Masha Allahu khairan Wa ahsanan jaza❤❤❤❤❤❤❤❤❤ subhaan Allah subhaan Allah very👍 very👍 good👍 job janab thank you🌹 very much👍
@Farm_fab Жыл бұрын
New vibration mounts for the generator to the frame will need to be replaced. I hope you were able to use high temperature black paint on the muffler, because if it's not, it will just burn off.
i hope no one is using this video as a guide to restore generators . that engine rebuild had so many mistakes , the valves were not adjusted , engine rpm not set correctly and so much more.
@SOURADEEPBISWAS
2 жыл бұрын
Also the thin rod that's inserted in alternator shaft as concentric rod is missing during installation.
@user-cv5um5qg6q2 жыл бұрын
كيف شتغل بدون تنك البنزين😏
@daviddesau43422 жыл бұрын
You VC- you boom boom Ho Chi Min !
@shankarmiyar2 жыл бұрын
Bolt nuts fresh? They are very very friendly?
@restoration-bq3921
2 жыл бұрын
thank you
@user-og6qx6th7h2 жыл бұрын
Why didn't you tighten the coil screw? .. The gasket recovery process is wrong
@kbsgamer01132 жыл бұрын
I sellut incuteble bruda
@user-bw8dy2id9l2 жыл бұрын
Зачем ты брызгаешь на болты не понимаю.Не может жижа твоя да и вообще любая другая за секунду ржавчину разесть. А отверткой поковырять в цилиндре просто супер.
@user-ic6vv4mn2i
2 жыл бұрын
Полностью согласен, да и он двигатель на воздухе завел о чём тут говорить
@saidAoahmed2 жыл бұрын
السلام عليكم ورحمه الله وبركاته
@ps52342 жыл бұрын
كيف اشتغل من دون خزان الوقود؟؟ Where the tank of gasoline??
@user-ij1nx3tq3z
2 жыл бұрын
عطاقه شمسيه
@user-bs3zp6fl7i2 жыл бұрын
А как они его завели без топлива? Бензобак то снят.
@user-zp2en4rj5m Жыл бұрын
Well thats an old engine.you should grind the valve to make it better and adjust valve clearances and you did not show how the timing of crankshaft and camshaft.
@kawaylaw8311 Жыл бұрын
Can you send me how to connect the ENGINE SWITCH
@Aquadus2142 жыл бұрын
Looks restoration at the cheapest cost on labor and materials. No significant effort has been done.
Пікірлер: 333
Vietnamese miracle. It even works without fuel. The engine shutdown switch is not connected either.
@ArmandPedroza
5 ай бұрын
I noticed too, the engine ran without gasoline.
The frame on the original find was rusted completely through. Miraculously it was fine later.
That generator is not running right at all you shouldn’t need a second person to rev the engine up when you apply a load to it
@anthonielegrange8688
8 ай бұрын
Just need to adjust the governor for the revs
Awesome. This video made me remember my father repairing all sorts of engines and cars. Thank you.
nice work, now you have a generator for power when you need it.
Always love it when people spray something like WD40 on a bolt, and then after 2 seconds try to loosen it.
Quedó nuevecito, que buena restauración.👍👋🇨🇴
Great video buddy. You have to be very careful mounting the generator end casing on & even more so the Brush set. Very careful indeed.
I've got the same exact generator without all the rust and mess. It helps keeping it out of the elements when not in use.
Not at all keen on setting the bearings that way, nor the complete absence of a torque wrench! Adjusting the tappets would be preferable, as would setting the bearings on the outer raceway, preferably with something softer than steel. Nice to see the youngster participating with his father to learn skills. The generator appreciated some care and attention after being abandoned, and I was surprised that all the fasteners unscrewed intact! All in all a nice restoration, with some finesse it would have been great. Subscribed.
@Skoda130
2 жыл бұрын
Some just need to work with the tools that they have at their disposal.
Друг, вот ты рукастый мужик!
I know these guys are working with limited tools, but to beat the center of a bearing is just asking for a failure of that bearing.
@restoration-bq3921
2 жыл бұрын
thank you
Considering where you found it I was expecting a baby cobra to come out. Since you stage so many finds it’s time you got yourself a workbench and torque wrench.
Great restoration with limited resources. Attention to detail by pre oiling most everything within the engine is great but use some wood blocks on the bearings the next time you need to set them in. This is the exact same gen set that Lidl has sold in the EU market, didn't realize it had an AVR module in it.
@restoration-bq3921
2 жыл бұрын
thank you very muck
@rezaramadhan6075
2 жыл бұрын
Lksnssn NK u.h N. Y
@user-yh1oq8ei5n
2 жыл бұрын
Рм? 0фх
@user-lm9sf6le5n
9 ай бұрын
❤❤❤❤❤
Amazing Restoration...!
Có cái ghế sa lông ngày xưa đấy phục hồi lại xem nào 🤣
You are woooooow 👍🤔 Tanks boos بصراحه انت روعه 👍🤔
Я думал он его сейчас помоет с фери покрасит и все.с компами они же так делают и работают 😂😂😂
Well done! 😊
God bless you, sir .... that place looked like the perfect venue for a snakebite!!! Plus you set both valve springs by hand. I would have received a cut thumb, gotten popped in the eye - or both.
@restoration-bq3921
2 жыл бұрын
thank you
@skhasibul4895
2 жыл бұрын
A
the spray paint not resist the gasolin ..i suggest useing sandblaster to clean aluminum parts ..and you must replace all gaskets and not use hammer to assemble the stator base because the camshaft may be break it .. good jop brother ..
You forgot to put the long screw that holds generator to motor crankshaft
رائع للغاية قناة مفيدة جدا .
Beautiful repair. Loved how the new throttle spring was stretched out to fit lol but for real nice work.
It's hard to believe it works!
Easy assembly of legs n wheels. Now charging battery, will try to start it in morning.
You did a great job and your work is so beautiful
salamat bro.detalyado Ang iyong demo...God bless.
Think of all the excuses we make here in America when it comes to not having the right tools or equipment. This dude went at it with what he had available and he got that thing running again. Even in his country where most folks would not even think about saving that thing. When you have nothing I guess you gotta make do. These videos inspire not to be such a woose and just go for it. We have everything and more in this country to do the job. Now back to procrastinating on fixing my projects outside. Jaaa
@dulatip2190
2 жыл бұрын
D
A totally new Lease on Life Bro. Beautiful restoration you just keep up the great work you are doing and I'll keep watching you and enjoying every minute of your shows .
Respect 🙏. India 🇮🇳
عراقي 🇮🇶مر من هنا
Доктор Дью по тебе плачет горькими слезами
Very nice job.
It is more like cleaning rather than restoration 😅
I take my hat off to the patience and memory of this guy, I would have just left the thing to rot and buy a new genny, I couldn't remember where all the bits went. Not keen on the method of fitting that bearing, should be fitted using force on the outer rim not inner.
Great, Very good step by step restoration effort, yet practically simple enough to follow and help people with similar difficult situations, Thanks again
@restoration-bq3921
2 жыл бұрын
thankn you
you not show when put rear long bolt that keep elwctric rotor and engine shaft together 🤔😂
Great job..... but you put ( camshaft ) wrong.... Thanks with my best wishes.....
a very extraordinary restoration from a condition that is no longer feasible to be an item that is fit for use & sale. cool
Wah g wah in Urdu Excellent" in English
Bom dia! Pra mim é uma honra viu prestigiar seu trabalho, vamos sempre juntos somar e fortalecer nossos objetivos, Conto com você, eu já estou por aqui.
Excellent Great Brother 🙏🙏🙏🙏
Wow good job bro
@cv.sahabatprima4677
2 жыл бұрын
Good job
Great restoration........
@restoration-bq3921
2 жыл бұрын
thank you
It's never a good idea to reuse bearings. If they were worn before you did the repairs, they will still need replaced. Depending on how they were removed, they may be damaged.
Excellent Video Great restoration What do you guys adjust your intake and exhaust valve in mm and what kind of Spark plug is used on the 196 cc engine. All trade make the same generator but it is modified to use propane APG 3535 cn
amazing restoration ! you are the shief .
@restoration-bq3921
2 жыл бұрын
thank you very muck
Cam ráp sai củng chạy được hay thiệt
Thanks for the amzing video, may I know what is the type of silver paint you use for the Crankcase and engine body? Is it a regular spray paint or is it a type of paint that can stand high heat?
Now THAT was one scungy unit to start with!
عمل جيد جدا يا رفاق
@user-hm9rp1cu7j
7 күн бұрын
بس نسى ما خلالها دهن ونفجر البستم بعد عمك
Merci pour l’exercice
This is just cleaning and refreshing not full restore
Ето това е майстор. Браво
I really enjoyed this kind of content, it's very interesting Da to learn a lot of the mechanics of these power generators just by watching their videos. congratulations on the great video 😊
@miodragtodorovic7924
2 жыл бұрын
Vlaške. Narodn. Nigre. I
خطأ كبير يرجع يخلي الكازكيت المستخدم 😑 لازم يخلي جديد حتى ما يطك الكازكيت وعندو اخطاء هواي بس يله احسنت التعمير
ГРМ не выставлен,клапана не притерты ))))
Find everything ... you !!! but where do you go to look, in landfills, in garages or other public or private places?
Nice Work!
Không thấy thay thế cái gì, hầu như vẫn để như cũ, chứng tỏ máy còn mới, chỉ để lâu ngày bụi bẩn thôi
Hay. Bạn ổ việt nam ? Nhìn đôi dép lào - nón cối là biết ngay !
I have one problem with this on this type of generator the engine's are almost indestructible but the electricity generators always fail & mostly avr's then the windings on rotor & lastly the stator it would be better/ more helpful to show the electricity generator being repaired as that's the most likely to fail.
16:49 - Các dấu chấm trên bánh răng phải thẳng hàng nếu không động cơ sẽ không hoạt động bình thường.
Das ist fantastisch!
Я бы один ,так резво поднять генератор не смог..!
Я так в первом классе разбирал! Плохо!!!
@user-gn3bg1eo9h
2 жыл бұрын
ס--ּ
انت فتحت القديم ونظفتة لكن مرجعت شديتة شديت بدالة جديد
@ailail-sx5st
2 жыл бұрын
زين شلون شتغلت بدون بانزين
Sure need some adjusting, sounded horribly. They could have made it 100% complete before ending the video.
Nice work 👍
Work Hard And Win The World 👍❤
taking the stator apart is ballsy
Very good i really love it♥️
@restoration-bq3921
2 жыл бұрын
thank you
@sixrsi3501
2 жыл бұрын
@@restoration-bq3921 b W
Respect bro🤙
@restoration-bq3921
2 жыл бұрын
thank you
@edupena5953
2 жыл бұрын
Respecto man
You can't just pull the rotor off the crankshaft that easy.
Cool a generator that runs on fresh oxygen
Tiêu đề tiếng anh ngt xem nhiêu hơn hã chú.
ARE YOU FIXED GENERATOR ENGINE😱😱😱😂😂😂😍😍😍😍😍👍👍👍👍👍👍👍👍👍👍👍👍
hola Y acá estamos... Hey Buen Video
Greetings, Cool project and Great job buddy as always like👍
@restoration-bq3921
3 жыл бұрын
thank you fou your
هناك غلط بل تجميع المحرك وهوة برغي الارميجر ما شديتة
@user-el2wp4xf6k
2 жыл бұрын
هو بس البرغي 😹بس الواشرات مال الكابريته هو يمكن حته دهن مخاله🇮🇶
Nice job ,
Wow so cool 👍 🙏🇬🇧
@restoration-bq3921
2 жыл бұрын
thank you
Masha Allahu khairan Wa ahsanan jaza❤❤❤❤❤❤❤❤❤ subhaan Allah subhaan Allah very👍 very👍 good👍 job janab thank you🌹 very much👍
New vibration mounts for the generator to the frame will need to be replaced. I hope you were able to use high temperature black paint on the muffler, because if it's not, it will just burn off.
اذا اكو اهنا عراقي خل يركز البرغي مال ارميجر ماشدة😂
i hope no one is using this video as a guide to restore generators . that engine rebuild had so many mistakes , the valves were not adjusted , engine rpm not set correctly and so much more.
@SOURADEEPBISWAS
2 жыл бұрын
Also the thin rod that's inserted in alternator shaft as concentric rod is missing during installation.
كيف شتغل بدون تنك البنزين😏
You VC- you boom boom Ho Chi Min !
Bolt nuts fresh? They are very very friendly?
@restoration-bq3921
2 жыл бұрын
thank you
Why didn't you tighten the coil screw? .. The gasket recovery process is wrong
I sellut incuteble bruda
Зачем ты брызгаешь на болты не понимаю.Не может жижа твоя да и вообще любая другая за секунду ржавчину разесть. А отверткой поковырять в цилиндре просто супер.
@user-ic6vv4mn2i
2 жыл бұрын
Полностью согласен, да и он двигатель на воздухе завел о чём тут говорить
السلام عليكم ورحمه الله وبركاته
كيف اشتغل من دون خزان الوقود؟؟ Where the tank of gasoline??
@user-ij1nx3tq3z
2 жыл бұрын
عطاقه شمسيه
А как они его завели без топлива? Бензобак то снят.
Well thats an old engine.you should grind the valve to make it better and adjust valve clearances and you did not show how the timing of crankshaft and camshaft.
Can you send me how to connect the ENGINE SWITCH
Looks restoration at the cheapest cost on labor and materials. No significant effort has been done.
Please remove background noise😢 I am frustrated