Full Building Design and Detailing using STAAD.Pro Connect Series and RCDC
STAAD stands for Structural Analysis and Design, the software is one of the most commonly used software used for structural Analysis and Design. It is a Product of Bentley. The software is used by students and professionals all over the world for Structural Analysis and Design.
RCDC is a product of Bentley for Structural Detailing and Design, footings, pile caps, slab, column and beams can be designed and detailed. We can also generate the design reports and find BBS using the software.
In this video we have shown
1.Complete Building Design in STAAD Pro Connect Series, including all the steps.
2. Footing Detailing in RCDC
3. Column Detailing in RCDC
4.Beam Detailing in RCDC
Download the Plan for Practice: www.mediafire.com/file/0qrn1u...
Check Out My Course on Building Design Using Tekla Structural Designer:
www.udemy.com/course/building...
Пікірлер: 65
You are great brother👍, I wasted money learning staad in Cadd centre, and not learnt as much, that I learnt from your single video. Thank you very much bro, keep growing, well wishes to you..💖
Great 👍. Thank you so much brother!
I am from mechanical background still watch this as it's really nice way of presentation 👌
Thank You so much for your effort
Very very thank you sir
Thanks bro
you are doing great bro, and Thanks for this amazing info.
@MainakChoudhury
Жыл бұрын
Thanks bro
Great
Super Sir👌👌. One small Request sir, make a video on manual calculations of a building (G+1)??
Sir thanks
when i import file from staad that is show a error "unable to read analysis data"
@MainakChoudhury
Жыл бұрын
Sometimes error like this occurs, it can occur due to many reasons, eg: for beam ,if you are giving a level where there is no beam. My suggestion is to start from a small model with 4 columns, once you have some experience, you can attempt anything
Does we get the BBS reports of all components in stadd pro
@MainakChoudhury
3 ай бұрын
In RCDC, yes
This is idealistic to consider column centre at node beam flush positions master slave etc needs Tobe considered
@MainakChoudhury
Жыл бұрын
While Going to perform design we don't know about the column size so its center is taken, later after design is completed we can overlap with the architectural plan and assign column locations properly by double checking
Sir, Kindly extend this video, for RCC slab design and detailing. It will be really helpful. Also please explain why you did not assign plate loading, mesh elements for slab
@MainakChoudhury
7 ай бұрын
1. Design: kzread.info/dash/bejne/a6WYs9t6f8vforg.html 2. Detailing: kzread.info/dash/bejne/fn2O0rqvh9HAfpM.html
Where can we get RCDC software,i did not see RCDC in stadd pro Bentley v8 software
@MainakChoudhury
3 ай бұрын
If you are using Staad connect edition, you should be able to use it.
When i try to import staad file into tekla one notification popup it says "check that it is not a manufacturing model" What is the solution for this problem
@MainakChoudhury
Жыл бұрын
Best solution is do not import, just make the model directly in Tekla structure. I know the advertising can be done in a presentable way, but in opinion there will always be some compatibility issues.
Can we use x and y coordinate and z as elevation insted of 'y'. You have taken y as zero in plane .
@MainakChoudhury
10 ай бұрын
That's the default settings in Staad, though you can change it
How to solve failed column and beam in design, or over stressed
@MainakChoudhury
Жыл бұрын
You can do it in Staad by increasing the size, however for RCC design Staad doesn't select failed members automatically, you have to check the design report and compare, which is difficult for big structure, so RCDC is better for solving the failed members.
What version of staad is this
@MainakChoudhury
Жыл бұрын
Staad Pro Connect Edition V22
Good day, what is the problem if the rcdc is unable to read the data analysis? Thank you
@MainakChoudhury
Жыл бұрын
There could be 2 scenerios 1. Staad file has some errors, check the analysis of the Staad file 2. Version difference between Staad and RCDC
@anjanae7384
Жыл бұрын
after analysis you may have access from staad pro connect software.
You are already selected min ne max dio of steel bars while in analysis and design part of stadd pro.then why you again choose the size of bars for beams, columns and footings in RCDC
@MainakChoudhury
3 ай бұрын
In RCDC we do detailing separately, so we have to assign, basically only the frame analysis results are taken into RCDC, the Design done in Staad does not matter, you can choose to skip it, only perform the analysis part.
@pydinaidu9966
3 ай бұрын
Bro I have been trying for installation of RCDC but it shows License does not found..can you help me to install RCDC
59:42 When i do the Beam Design it show beam is missing?
@MainakChoudhury
Жыл бұрын
Select only one level, if you select multiple then it will show missing
@rahulfaraiya874
Жыл бұрын
@@MainakChoudhury thanks,it is working
Sir plz upload simple g+2 project stadd+rcdc
@MainakChoudhury
Ай бұрын
Uploaded especially for you, except for the RCDC part.
Sir..Can we use staad select series and RCDC
@MainakChoudhury
Жыл бұрын
Yes
Translation repeat la mode la use LINK SPACE option click then u can apply ok use the method ...
@MainakChoudhury
6 ай бұрын
Dissimilar Floors
Sir give me downloading link of the software
@MainakChoudhury
Жыл бұрын
It's not allowed in KZread platform, you can search in get in to my pc website (no spaces),
I noticed in column design higher story have more reinforcement than lower story column why this is confusing plz explain if you have solution
@MainakChoudhury
8 ай бұрын
It happens no worries about that, the structure is complex and many loads come combined through other members, so this can happen.
@shafeeqkhan5794
8 ай бұрын
@@MainakChoudhury bhai kuch solution ho aap k pass to bata do
seismic parameters not getting loaded :(
@MainakChoudhury
Жыл бұрын
Which version are you using
Instead of suffering to generate column through nodes We can use link option while doing translational repeat
@MainakChoudhury
Жыл бұрын
It works differently for dissimilar floors, practically most buildings are dissimilar, so this way is preferred. I know you are telling this because in most tutorials they do this, we can easily do that when the floors are similar. But we have to dig deeper, have you seen any house having similar floors? The answer will be very few, so dissimilar floors means, dissimilar beam arrangements, hence this approach. Also do you expect to have columns at all intersections? There can be intersections due to beams also. In that case you cannot use linked steps. Hope I could clear your query.
@kalpanabind1471
5 ай бұрын
U r right when i did link steps,it make column at every intersection
Please using building option again 🙏
@MainakChoudhury
Жыл бұрын
Didn't get your point, can you elaborate please
@mahendraaandkaanchanpatil1489
Жыл бұрын
@@MainakChoudhury Sir there is building planner option to generate rcc buildings layouts of slabs and it automatically generates 3d model with precision column beam offsets Only problem is you need to apply seismic loads in staad before analyzing
@MainakChoudhury
Жыл бұрын
@@mahendraaandkaanchanpatil1489 ok, got you you are talking about Staad building planner software. Till now I use Staad, RCDC and AutoCAD or Tekla+ AutoCAD to present those things in my final drawings. But since you suggested I will try using that too. Edit 1: I have tried using the building planner option but it doesn't work since I do not have autocad 2007
Make it in hindi, in english we alredy have so manny good forign tutorials
@MainakChoudhury
Жыл бұрын
Thats true, but the language of the channel is English if I have more resources then I will make a new channel in Hindi. Also foreign tutorials are not focused on IS codes, so there is a need.
@abdullahiahmedmohamed3925
Жыл бұрын
@@MainakChoudhurywe actually need an English version sir thank you
modelling in staad is not the best in the system at all. likewise its detailing where you cant have all the information for a beam at once. cantilever slab is also a problem
@MainakChoudhury
Жыл бұрын
Every commercial software has its advantages and disadvantages, you have to pick the one which works best for you
randomly doing things without any explanation or detailed steps, he is just using the software it is no course disappointed
@MainakChoudhury
3 ай бұрын
Sorry