The problem with this engine Is the placement of the water pump.

@rjdatdude23

4 жыл бұрын

Yup. Good job Ford

@Straightforward-iPhone-Tips

4 жыл бұрын

It broke and flooded my engine a few years ago, previous owner had to rebuild the engine.

@clipsedrag13

3 жыл бұрын

alternator

@davidcoleman9304

2 жыл бұрын

Another of Ford's "BETTER IDEAS". Like their AWD, PTU, units NO DRAIN PLUG ideas. Saying that 18 0unces of oil will last the life of the vehicle.

@boostedrex9460

2 жыл бұрын

@@davidcoleman9304 I got 190000 miles and I never had any problem with drive train awd or transmission

I'm a 34 year old lady and house wife don't know mechanics my brother was going to fix my 08 ford edge and he caught covid I saw this video and i fixed my car yesterday myself I'm excited and so happy.

@thereallboogiegohrd6582

7 ай бұрын

Great job. I'm also going to attempt this

Local shop said 758.71 plus tax, I thought a little high...watched your video 7 times, easy peasy mkx running like new. Many thanks , 100 buck injectors and intake gaskets hr n half time.

Don't unbolt the throttle body from the upper intake. Just take the bracket bolt that is below it, out. The throttle body will come off with the upper intake. Also, If you can, use a blow gun and compressed air to blow dirt and debris off from on and around the upper intake before unbolting it. Place a piece of cardboard cut to fit over the top of the intake ports to keep stuff from falling in there.

@chassy

2 жыл бұрын

Excellent advices. 👍

@jerrywillis5744

10 ай бұрын

I didn't and it was still easy peasy, thx

For anyone watching this in the future. Be sure to release the fuel pressure in the lines before disassembling parts. He didn't explain it in the beginning of the video, but it'll be best to do this first before anything else.

@FSchimidtBR

2 жыл бұрын

If you don't do that, can it cause some damage to the fuel pump?

@davidsnyder3799

11 ай бұрын

@@FSchimidtBR Possibly, from the ensuing fire.

Great video, saved $1000 doing myself. I only did few things differently: I removed battery and used bungee cord to hold wires out of way. Did exactly everything else. Thanks guys!

@lepra2390

2 жыл бұрын

I'm about to do it my self too ,wish me luck

I just replaced a fuel injector on my grandmas 2010 fusion 3.5L; had CEL for P0201 “injector circuit open” “cylinder 1” I was able to tear into her engine by following this video, and had the #1 injector replaced iand put back together in 3.5 hours. Word of advice they don’t mention it in this video but before you do anything, pull your fuel pump relay fuse and crank the engine to relieve the pressure. Also disconnect the negative battery terminal

@jayrenner211

Ай бұрын

They do mention this.

Best video ever explaining what I have to do tomorrow with an accent I enjoy listening to, SUBSCRIBED.

Solid video. I appreciate you being so detailed and especially showing how to remove the different types of clips. Thank you!

This video was very useful. I am NO mechanic but was able to handle this job with some sort of ease because of the help. Thank you!

Video was very helpful. I changed only 1- injector and this guy made it easy for me to do it my self.

@jvanlans2752

3 жыл бұрын

Hey when you changed one injector did you have to reprogram it

You guys just saved me over $400! I subscribed, liked, and even clicked a sponsor VRBO something I've never done at a KZread fix.

Want to take a few minutes to Thank You! for this video. It not only gave me the courage to tackle this project myself but, also made the job easier to do. In my case I have a 2008 Ford Edge. It's slightly different (no pressure release valve on fuel rail) but, still was a big help. I replaced all 6 of the injectors even though the #5 was the problem. Well done and again a big THANK YOU!

@availablehandle68

2 жыл бұрын

How did you manage to release the pressure then?

@ashleylane2020

Жыл бұрын

Mine doesn’t have the release valve either??? What did u do to release the pressure

I also did my sparkplugs since you can get to rear three plugs while doing injectors

⛐ Check out our Garage to see what tools we use and recommend: www.amazon.com/shop/worldmechanics ⛐ Subscribe and hit the notification bell by the subscribe button for new videos: kzread.info ⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys

Y'all are informative and hilarious. Keep up the good work!

You guys are awesome I learn sooo much from the videos ypu guys make👍...

Thank you for making this video. It helped me tremendously when replacing my own injectors.

@muhammadasimrasheed4007

3 жыл бұрын

Hi guys,...any help regarding to above issue?

@eunicenelson812

2 жыл бұрын

I have a 2011 ford explorer gasoline is in the intake manifold coming through the throttlebody down in air filter housing . what cause this?

Thank you guys so much for the help with this video! Saved me a lot of trouble

very helpful. I need to know which injector is which. I will look it up but Big thanks !! Saved me a lot of money!!

One thing I'd suggest dip each injector in a bit of gasoline for easy insert I tore my car down twice second time the gas trick is what worked because the first time the injectors were not in properly.

This is why i miss my old 2002 Mazda P5. Car was so much simpler to work on. In the 11-12 years i had it only needed a thermostat, maf sensor needed to be cleaned once and towards the end i replaced 2 ignition coils at $20 a pop and it took 10 min to do. Since i got the lincon had to replace the transmission and now this fuel injector and i keep hearing about the water pump possibly going out.

Excellent video!

3.5 would be a great, reliable engine if not for the water pump location. Change engine oil and coolant regularly.

Question: If the car sits overnight, is it safe to assume that there is no pressure in the fuel line, and it is safe to remove the fuel line?

Love your video . It’s very detailed and thorough demonstration ! Subscribed

Done. Thanks guys

I removed intake with TB. Saves couple sec for you. Much more for me. Thanks for the video.

@rubyblack6682

3 жыл бұрын

Tb?

@DK-bk1vq

2 жыл бұрын

@mathermp what'sa TB?

@Itzkwann

2 жыл бұрын

@@DK-bk1vq throttle body …

@DK-bk1vq

2 жыл бұрын

@@Itzkwann Damn! 🤦‍♂️ Lol

Thank you very helpful, Do i need to replace them all, or replace as per the scan code reading

Very good video! What do you charge for that job on a flex?

Gorgeous

Yes, I removed the throttle bracket instead of the throttle body

I have a 2014 Ford Taurus and replacing fuel injectors but can’t figure out how to take clips off of the injectors

Am I the only one who got lost on relieving the fuel pressure? All I heard was there's a special tool, they have it, but wouldn't recommend it. Do it? Don't do it? ..so Remove the fuse for the fuel pump and the relay and run the car til it runs out of gas? I'm lost on that part.

Does this video work for the Base Model Ford Explorer 2014 ?

you can do this without open throttle on the antec's body

I just changed my injectors car runs perfect but now hard to start any ideas? Originally was misfire #2 cylinder replaced plugs and ignition coils still got the misfire code but starts without issue. Now don’t have a misfire car runs great but hard to start cranks a few extra times now.

@alandxoshnaw317

3 жыл бұрын

it caused by fuel pump

How are those springs supposed to go on.

Is that same engine set-up as an mkz 2006 I gotta replace bank 5

Wow. Only tool needed is a 8mm socket with extension and ratchet. I would cover openings before removing intake. Rat poop all over the intake could of went into the opening.

I need help with fuel injector sensor location a my ford explorer 2012 3.5 v6.

Internal water pump triggers me. Never again.

Anybody know the flow rate of the oem fuel injectors?

Can a bad fuel injector dump fuel into the intake? I’ve noticed fuel dripping from the cylinder one injector. My wife Ford Flex had a blinking check engine light with the code PO301 misfiring.

@charrobudligth

2 жыл бұрын

Was it smoking?

@joonajks

2 жыл бұрын

@@charrobudligth yes it was smoking, jerking with a strong fuel odor. It was a bad fuel injector!

@Dr650rob

2 жыл бұрын

Ya and it'll ruin the cats

What is the special tool you need to release the pressure on the fuel line? He said don't do it if you don't have the special tool but didn't say what it was...

I need your help 2014 Taurus 6 Cilinder code P219B I replace fuel injector , intake gasket, spark plug, and it’s not solving the problem any ideas please

Hi would I get an engine light if anything is wrong with the fuel injector? I’m because, my 2010 Ford Edge hesitates and jerks between 55 MPH and stabilize at 70 MPH. This is after changing coils, spark plugs, air filter and cleaning the throttle body. I don’t get any engine lights on my instrument panel.

@Naptownapollyon

Жыл бұрын

you also could have a dirty carb. dirty fuel pump, faulty fuel pump, Bad Throttle body sensor "lease option", Bad 02 sensor would also cause it.

Ok, I’m at the 6:10 mark where you take an obvious pause and then say, “now you go ahead and remove the bolts…” I can’t seem to get the bolts out. They get loose and just spin. All except the bolt on the top of the manifold. It came right out. I’ve looked all over for a solution like- “when it is loose and spins freely, turn it - to the right until it lets go completely” or something similar but I’m stuck here with no idea what to do. Can anyone help please??

Which one is cylinder 5

What number fuse goes to 2008 fuel injection

Hello all! I have replaced fuel injectors of my Fusion 3.0L V6 twice, and both times the pressure regulator of the fuel pump throttle has failed, causing long starts when the engine is warm. Does anyone have any idea what could have happened to the pressure regulator to fail? Is there a secret trick to depressurizing the fuel line or re-pressurizing it before starting the engine?

I have ford edge 2011. Sometimes, wrench warning appears along with engine fault, engine decreases speed and despite pressing accelerator car reduces speed and then starts jerking... Seems like it's some sort of engine missfiring.. I got all plugs replaced, throttle body cleaned but problem still persists... It happens on low speed by the way. Need someone to kindly share a solution... I m thinking to get fuel injectors checked, repaired or replaced but will it eliminate the issue?.

@bluesbrother2383

3 жыл бұрын

Sound like an o2 sensor, usually the most common problem with those engines, use an obd2 reader and it should tell you exactly which needs to be replaced

Change the plugs, too!!

Remove fuse for fuel pump relay and what?

I have a 2013 Ford Taurus with a code p0430 check engine light turns off then few days later it comes back on again with the sale code any idea what is causing it to do that ??

@simplybuilt_1708

4 жыл бұрын

It’s your oxygen sensors after the catalytic converters that aren’t reading correctly. I had this issue on my SHO. Just replace the sensors, run for a bit and you should be good. Hope this helps

@HectorMartinez-ub3bx

4 жыл бұрын

Simply Built_ did you have the same code p0430 ??

@Dr650rob

2 жыл бұрын

I have codes 420 and 430 and on a cold start I got cylinder 4 misfire. I'm wondering if injector 4 is bad which ruined my cats I'm also getting bad mpg

So what’s wrong with 3.5 Ecoboost and when it occurs?

@MTLaz16

4 жыл бұрын

Same here, I would like where u found info on which injector is for which cylinder. I have a.Chilton manual but does not tell me much.

@DK-bk1vq

2 жыл бұрын

I had a P303 reading on the fault reader. In this case Cylinder 3 was misfiring. It could be the spark plug, the coil, fuel injector, or a vacuum leak. Mine was the coil.

All that work for 6 plugs 😭😭

so much time has passed and this automobile has not appeared in russia.

Replace plugs while you're back there.

first thing disconnect neg.battery term or u will be using fire extinguisher and call fire truck then have big problem wife get mad kids have to walk to school oh no🤤

Comment

@duanal

2 жыл бұрын

Reply

FRANÇAIS

easiest way to tell that someone doesn't regularly work on cars is when he wears his bling while shooting the video. If u want anyone to take you seriously, take the watch and ring off.

Never wear jewelry while working on a vehicle. That is a serious safety hazard and you could also cause damage or get it caught on something.

"Guys". Omg this guys videos are so hard to watch.