Thank you for your help. Set mine up with your quick recommendations and it flies great. Thanks for posting this.

love watching these things fly!!

Well done. Great setup video...

Thanks for putting that bit about using a mix to open/close the drag rudders. I set that mix so I can close drag rudders for transport too, I simply put the mix active with throttle cut on (EDFs disabled). That way I don't have to manually close the drag rudders for transporting the model/putting it back in the box.

@mfh9780

2 жыл бұрын

firefoxussr31, How do you do this mix that you mentioned? The mix mentioned in the video relies on me flipping the switch for right and left, how can the mix you mention handle both sides attached to throttle cut? Love the idea. Thank you

@almari222

Жыл бұрын

Great idea!

Round two. I am very interested in your thoughts after the maiden as well. Nicely done!

Thank’s to your video maiden today was perfect, not even trim needed ! Thank you so very much for sharing.

Great job and video. Good luck 👍🏻✌🏻🖖🏻

Great setup video! Love Solt's but you had a few great pieces of advice that would have made it way faster. In fact, I'm going to double check it all again.

You're a saint, I dont care what Photon says.

You the man I set up mine the way you instructed and walla it works great and i turned of the mix so I won't make a boo boo while flying 👍👍

@firefoxussr31

2 жыл бұрын

you can do what I did, i setup the mix only active with throttle cut on. i'm doing that so i can close the drag rudders for transport without forcing them closed manually.

@drabun1959

2 жыл бұрын

O.k that sounds like a great idea

Love it dude 😎

niiiice! Beautiful Jet!

I know 8mm looks like a lot of up trim to me too when I did mine.

Good video, using your method I cant adjust the drag rudder push rods short enough when the drag rudder doors are clamped shut. Do I need a shorter push rod?

Do you recommend setting up high and low rates for all control surfaces or ? Any expo?

Hi Dave. Given the mixing board feeds in some aileron input to the drag rudders, are you concerned about setting up the clamshells to physically close with rudder input alone? At full rudder, any roll input (from the pilot or the gyro) is then going to try and force the clamshells to close even further...

@TheRCAirMarshall

2 жыл бұрын

I thought about it, but it’s honestly not that big of a concern, IMO. Each pilot is going to fly the way they want of course, but this really isn’t the kind of plane that needs a ton of rudder or aileron input in the first place. If you’re trying to snap roll a B2, I’d probably give myself a little more room in the clamshells. LoL 😂

NIIIIIIIIIIIICE! 😁👍

Where can I buy a stand like yours? That’s perfect for that plane.

Awesome Video…do you leave the travel in subtrim at 70 or do you take it back to 100 once you get it set up?

@TheRCAirMarshall

11 ай бұрын

It’s been a minute, but I do believe I left it at 70. Leaving it at 100 would cause the servos to bind.

Where does the UBEC/BEC PLUG GO that comes on the battery plug?

What an awesome instructional video. Thanks for taking the time to do this. Did you use a Spektrum receiver? Any pointers on hooking up everything to the receiver?

@TheRCAirMarshall

2 жыл бұрын

I just used a Spektrum AR6610T Rx. Hook it up just as it is laid out in the plane. 1: Throttle, 2: Aileron, 3: Elevator 4: Rudder 5: Gear. There are no flaps, so I connected the gyro mode to channel 6. I just assigned channel 6 to the same switch where I would normally have my safe select/AS3X switch.

@mfh9780

2 жыл бұрын

@@TheRCAirMarshall Thank You

@mfh9780

2 жыл бұрын

Set everything up yesterday on my spirit, your procedure was outstanding. Thanks again. When are you flying your maiden?

@TheRCAirMarshall

2 жыл бұрын

Hopefully soon. My work schedule is a beast, and every good day of flying here I’ve been out of town. 😂 Hoping for good weather next weekend.

@mfh9780

2 жыл бұрын

@@TheRCAirMarshall Flew my maiden yesterday. One click of down trim needed and a few clicks of left trim. Nose gear tracked right a little, once back home I noticed the left main gear and nose gear steering needed a little adjustment. The B-2 flies very good. I literally flew with 30-50 power and the plane moves. I was able to land it with no problem. Thanks again for the setup instructions. Somebody had mentioned using the prescribed rudder mix on their throttle cut for storing the plane in the box. Do you understand what needs to be done there? Seems like only one wings rudders would get stowed.

Mr Dave i have a 6500 mah lipo that i simply can not to balance in the B2 I was wondering if you could give me any help! Thanks

Where did you get that fold out table that you’re using as a stand?

@TheRCAirMarshall

2 жыл бұрын

That’s an Ernst Ultra Stand. You can pick them up at BitGo hobby. Would appreciate if you use my link to BitGo at rcairmarshall.com 👍

Quick question did you leave your servo travel at 70% or did you return it back to 100% travel?

@TheRCAirMarshall

2 жыл бұрын

It’s still at 70%. To get the drag rudders to have 45mm spacing at neutral, that’s the travel that worked the best for me without stressing the servos. You could use this method using 100% travel, just understand that the clamshells will be open to closer to 55-60mm at neutral rather than the 45mm as called out in the manual.

@shermanbellmyer3297

2 жыл бұрын

Thank you so much for sharing the information, and making set-up easier for the rest of us. Awesome videos.

I got a question Dave did you add any DR/EXPO ?

@TheRCAirMarshall

2 жыл бұрын

No DR, but I do add 20% Expo to smooth out the stick center.

😁😁🇺🇸🇺🇸👍🏼

Did I miss the Maiden on this plane ??

An absolute Saint 😇🛩️! LET'S GO BRANDON 😉

@starfleetactual1909

2 жыл бұрын

The Flock of Fox.

Ever thought about cycling🤔

@TheRCAirMarshall

2 жыл бұрын

Oh no, I’m more of a swimmer. 🤣