Good job, I have worked in the R&D at a gas appliance manufacture, many hours spent on gas venturi development, along with orifice design, your design of adjustable orifice location and primary air adjustment is exactly what a good setup needs, advanced orifice design is really only needed if your trying to hit emissions and efficiency targets.

Louisiana folk have been making jet burners forever for crawfish pots . I have one made from 4 inch square tubing that burns so efficient the flame is barely visible . Your concept is cool at any rate .

@MrNonius

2 жыл бұрын

thank you

This is the standard burner that most every blacksmith and smelter uses. Same design that has been around for soooo long. And nothing turbo Bout it. That is a venturi burner.

@Afro408

3 жыл бұрын

Exactly, but there are plenty of wankers around reinventing things and using Turbo! and Insane! In the descriptions. 🤣😏

@MrNonius

3 жыл бұрын

each has its own characteristics, but the principle of operation is the same

@MrRomanblond

3 жыл бұрын

@@MrNonius I watched a lot of videos how to make a proper gas burner and the most of them aren't that powerful and so simple to build as yours so I agree that your burner is a real deal, could you specify the exact length of the tube, adapters and gap between nozzle and adapter in mm.? because I can't really understand what is added in the description

@samcoon6699

3 жыл бұрын

@@MrRomanblond I'll try to help. Looks like 1ft pipe 1inch diameter. 2"x1" flare adaptor. MIG/flux core welder tip. Don't know what size. Hex threaded standoff. Then a bolt of some size. Then just scrap pieces of metal.

@AA-zv6yo

3 жыл бұрын

For orifice sizes theres charts online.

Thank you for the video, I have watched it numerous times, and made my own version of your turbo burner, with a few tweaks to the design to fit my needs. Mine will be connected to a 100# propane tank. I'll be using it to heat my foundry, though, if I wanted to, I could adapt it for a small forge as well.(currently I use a coal forge) The only issue i have at present is how to connect the propane fitting to my burner. I believe I used a 3/8" bolt hollowed out, with a .035 weld tip as my gas feed. I have no idea what fitting(s) to look for... will probably hit up a hardware store with my bolt/plate and propane regulator hose in-hand to see what I can come up with.... sorry for the rant, thanks again for your inspirational video!!!

I appreciate the sarcasm when he was showing what you need. Silent sarcasm... I love it

Undoubtedly these burners are very necessary and with great performance, it is a great tool and make everything flow faster.

I found the video interesting, I had never seen how to make or model the gas turbo, for more videos like this I liked the video, but it is only for those who understand, I only admire

@jmbstudio6873

2 жыл бұрын

Not turbo. No blower motor. Naturally aspirated with choke. NOT TURBO.

I have always respected the work of people who work with metal show off their skills in making products such as the turbocharged blacksmith sburner can increase the flame by increasing the pressure, but I think it's enough it's a pity mine barely works.

@jmbstudio6873

2 жыл бұрын

Turbo or forced air needs a blower motor. This burner is NOT forced air or turbo. It is naturally aspirated with a choke.

Super burner, have long dreamed of such a, will have to make, thanks for the tip!

Всё гениальное очень просто, надёжно и функционально.

@MrNonius

3 жыл бұрын

Да))

It's great to see professionals show off their skills in making products such as the turbocharged blacksmith stove gas burner.

Nice burner. Looks like a very consistent, well-behaved flame. That would go great in a foundry.

Brilliant, very simple but effective design, cheers.

@MrNonius

3 жыл бұрын

Thank you!

You really are an artist.

You have a great burner, it's a pity mine barely works. It would be great if you left a link to the product. Warms really powerful! Great movie.

Really cool idea and thanks for sharing your thoughts and great video

great up-to-date video watched with pleasure I recommend

احسنت ياصديقى عمل جيد هذه الشعلة الصحيحة لخلط الغاز مع الهواء والتحكم بهما

отличная горелка для безгазовой зимы ! жгите, а мы вам лайкосы

@MrNonius

Жыл бұрын

Спасибо

You've got an interesting video. Need to go to the store and see the product

Super burner! I liked it a lot and it helped me a lot

Think I just found my next small project. Thanks.

Thank you for the good video. Think would be best to have the disposable gas canister out of the way when welding and grinding on the bench. Know they should be self sealing, but once had one leak.......

@MrNonius

3 жыл бұрын

ok thanks i'll be careful

excellent video. I liked it a lot and it helped me a lot

Beautiful blue!

I built a burner similar to that (Reil) and had to run gas at 30psi (2bar) melt my iron for casting. I then I added a fan ( a vent fan off of a water heater the building had negative pressure) to it and cut gas pressure to 15 (1 bar) and had the same results in a #16 furnace, it also does quite well in my #60 tilting furnace, in the #60 furnace, once about 1/4 (50Lb) full it starts melting at the rate of 1Lb per min i have only went up to 100Lb in that furnace but is capable of 200Lb.

Quem saber saber mesmo faz ao vivo 😊😊 parabéns professor

Great video! Just a comment--the straight tube needs to be long as you show in order to get enough air/fuel mixing for stable flame. Many burner failures are due to inadequate mixing before the flame front at the exit!

@MrNonius

2 жыл бұрын

Thanks. I have a 300mm tube

Merci beaucoup pour votre travail 🇲🇦🇲🇦🇲🇦🇲🇦🇲🇦

@MrNonius

3 жыл бұрын

Merci

I do like the mixing adjustments on it.

@MrNonius

2 жыл бұрын

😀

@jmbstudio6873

2 жыл бұрын

It is called a choke.

U have a creative mind

Sensacional parabéns ótima ideia obg, obrigado

@MrNonius

3 жыл бұрын

que bom que gostou

that is incredibly clever

Interesting. Some suggestons. 1. use a stainless steel reducer for the flame holder; mild steel won't last long. 2. Not everyone has access to a lathe. could you use something like a 1/4" pipe nipple instead of drilling out a bolt? 3. It looks like it works well but i wonder if a gas mixer would help? I used them on my blown forges. Looked sort of like a six petaled flower but with the petals twisted to about 15 degrees off the axis of the tune

@andreykrasehin2823

Жыл бұрын

Вообще-то у него чугунный переходник!

Wow this is interesting bravo!!!

You should add a blower motor to the end to force air into it. I used a old air mattress blower and attached a dimmer switch to it so I could control the speed. You just have to dial it in and it increase the temperature drastically.

@MrNonius

2 жыл бұрын

thanks, I will take your offer

@jmbstudio6873

2 жыл бұрын

I used a tee at the top of my burner and added forced air with an electric blower motor. I simply used a tee and a ball valve to control air, all pvc. Forced induction is the only way to forge imo. Naturally aspirated, with or without choke, can never come close to forced induction performance. Also the galvanized fitting will give this person zinc poisoning.

@CelepukEmplep

2 жыл бұрын

How about Air Compressor? How many PSI for the pressure?

@gyrosmith

2 жыл бұрын

I have used a hair drier to blow air into a charcoal furnace and it would melt bronze. I love your video. It opened my mind!

@LBCAndrew

2 жыл бұрын

Forced air burners are not so simple. You can't just add a fan and it goes brrrrr. You need much more tubing, a needle valve, and many other parts.

Unless I miss the mark, the burners in my Chili Forge do the exact same thing. Forced air and a ribbon burner? Now we’re cookin’ con gusto!

@jmbstudio6873

2 жыл бұрын

This burner does NOT have forced air. It has a choke and is naturally aspirated. Forced induction burners have a blower motor.

Fun video. I will have to make one. Subscribed!

@MrNonius

2 жыл бұрын

Thanks

Muito bom! Qual o comprimento do cano ? sabe se tem influência se maior ou menor que o comprimento padrão?

good video thanks to the author. Respect

ВАУ !!! БРАВО, СУПЕР!

Wow! Big like! Amazing!

Simples e eficiência, 👏👏

@MrNonius

3 жыл бұрын

obrigado

Perfect & Useful Thanks

No shitty music or cringey sound effects check no unnecessarily long intro or outro check no word overload, dorking around nor "like comment subscribe" crap check ample proof of work at the end check great video and burner Good Job

@MrNonius

2 жыл бұрын

Thank you very much

Its Realy Very Good Dear.

@MrNonius

2 жыл бұрын

thanks

А у меня есть стандартная заводская грелка-горелка! Работает так что аж уши закладывает,а если ещё и чистый кислород в дутьё подключить,то вообще улёт. А это обычная энжекционная горелка. У меня была подобная, только мини горелка я ей поросят смолил.

@MrNonius

2 жыл бұрын

Это хорошо

Thank you...explained a great deal.

@MrNonius

3 жыл бұрын

Happy to help

Супер горелка можно использовать как на кузне нагреть и ковка металла и даже плавить железо

Chispas...que cantidad de energía...gracias por enseñar...hare Krishna

Exelente trabajo ¡ El pico q orificio tiene ? ( mm)

Got 2 make me one of those……great build….

@MrNonius

2 жыл бұрын

Thanks!

Mujhe yah video bahut pasand Koi Kamal ki video

I like that .that's Awesome 👍

👍👍mantap..luar biasa,.

Gracias muy bueno

Wow great idea thanks

@MrNonius

2 жыл бұрын

😀

Incredible MASTER genius , I am amazed and want to learn from this MASTER modern tutorial . Introduce me GUN GUN from INDONESIA 👍👍❤️❤️🙏🙏

@MrNonius

2 жыл бұрын

Thanks. all sizes are in the description for the video

hello from iraq with you amazing

Very nice u forget a spring behind the nut to fix it

Good job. Well done! Thanks for showing it.

Super exciting brow

Просто Гениально!!!

Vera level antha match box with sticks

Thank you

boa tarde ficou top vc usou cano de ferro normal para fazer a bengala ou galvanizado

@MrNonius

2 жыл бұрын

tubo de ferro comum

Clever Man, very clever Hands... Amazing Torch, with simple materials; respect.

@MrNonius

3 жыл бұрын

thank you very much

I love this

Good luck with your member

Nice tool. I also worked with him.

Um ekipamento bem feito dez

Boa noite, perfeito, uma dúvida, funciona sem o bocal da chama com eficiência também?

@MrNonius

2 жыл бұрын

sem um bico, este design não funcionará

Buen diseño 👌🫂🇦🇷

hmm, i'm going to need a non lathe version. maybe i could use a threaded tube for a light fixture instead of center drilling a bolt, which is basically impossible for me. as far as the intake face, i'm willing to bet that it would function just fine unfaced since you need a fair gap anyway for proper combustion.

I see that it's very turbo!

Muchas gracias

@MrNonius

3 жыл бұрын

Por favor

Great video. But if this burner will heat an enclosed furnace, please show it working in an enclosed furnace, where there is no additional air to support the flame. Some burners work much differently in the open air and inside a closed furnace. Thank you.

@MrNonius

3 жыл бұрын

Thank you

Hi, very informative video. I wanted to ask you how many KW the burner develops or how many BTUs...? Thank you

How can you make a very powerful blow torch that is not so noisy & projects a really Long flame 🔥 like a 👉Flame Thrower 🔥 ?? 😕☹️🤦🏻‍♂️ or that can be adjusted to say from 200mm to 500mm ??

Insane surface footage on your lathe...

@MrNonius

2 жыл бұрын

Thanks

very good

Very nice

@MrNonius

2 жыл бұрын

🤩

Parabéns pelo trabalho, e obrigado por compartilhar. Uma pergunta: Esse queimador aguenta ficar 10hs em trabalho, ou teria que usar outro material?

@MrNonius

3 жыл бұрын

Obrigado por boas palavras. Bocal do queimador em ferro fundido. Este é um material bastante durável. Acho que vai sobreviver.

@KduBorges1

2 жыл бұрын

@@MrNonius teoricamente antes do queimador nao deve esquentar.

@tormetecbrasil3226

2 жыл бұрын

@@KduBorges1 aguenta sim pois quantidade de calorias fica depois chamas nunca dentro bico egetor

Hello brother, it's a good idea, but there is a question. Can I bend the tube from its front so that the flame is upwards and not horizontally?

Amazing

If you’re gonna go to all of the trouble to lathe some of the parts, why not remove the threads inside burner nozzle and Venturi air intake?

I have similar but only makes a lighter type of flame. Will not melt even copper in my furnace.

Super bro

Disculpe el gas natural de cocina alcanza esa temperatura de 1000grados

excellent

Sirve para horno de panadería

Super Bro

Merci. Monsieur

Nice job sir,excellent.

Good 👍👍👍

with that! you dont need oxygen to heat metal its very good could make a great heater as well !

Thanks u r a genue

А чем удерживается пламя? У меня точно такая же и при высоком давлении пламя срывается

Ficou loucura,top demais

@MrNonius

3 жыл бұрын

Estou feliz que você gostou))

Genio!