Hope you’re feeling better soon … how you keep pushing yourself when feeling so rough , is incredible 👍😁
@FatHead19797 ай бұрын
Great video. Clear, concise and no 12 minute preamble like some channels. This is the 1st clip I've watched from this channel and I've subbed as a result, keep up the good work mate 👍
@scotspie501douglas77 ай бұрын
once again Baz great video you make timing belts so easy
@19jacobob933 ай бұрын
Just replaced my factory original timing belt after 16 years and 177k haha It was still in operational condition, but had a few cracks developing and the water pump was weeping in the same place as this one, with a lot of dried coolant starting to build up below it... The cam chain rattles for roughly one second on start up, but I've heard this is relatively normal. I will add that the timing belts pretty much never fail in these. They have a rare occurrence where the belt will strip the teeth, but this is caused by the hp fuel pump locking up on the opposite end of the camshaft.
@pauljordan40617 ай бұрын
Nice work, with good advice. Videos to the point and not too much waffle
@_alphaautos7 ай бұрын
Amazing work as always! Hope you feel better soon buddy!
@ANDY-we7mr5 ай бұрын
Baz i had the flu the other week mate its a,killer looks like the same set up as the Ford kuga 20lt diesel video's you done good job
@BlakeCDS14 күн бұрын
Hi Baz I have a leaky front crank seal is there much more work involved after timing belt is removed, crank pulley pulls off easy enough from my experience, love the content keep it up 😊
@bazmeredith
13 күн бұрын
Straight forward buddy and thank you 🤙
@itswais772 ай бұрын
Don’t worry, you’ll see the Peugeot/Citroen TU 1.1 and 1.4s, I’ve had the belts break lots of times, one time I got away Scot free without bending the valves but the head gasket did fail a few thousand miles later
@christhackrsy7 ай бұрын
Done a few of these not nice getting crank locking pin in lot easier on 1.6 on front reluctor ring
@raymondzenzelencube54633 ай бұрын
howzit Baz, nice one i have been wondering here, my Ford Focus tdci need a foot on the gas pedal to idle otherwise its wont idle instead it will die could it be the timing being off?
@riskfreesolutionsforbusiness4 ай бұрын
tried heat &air wrench pully bolt wont move .thinking if i put car in gear break on will i get away with not having lock fly wheel up or is that asking for trouble?
@abdulb11622 ай бұрын
Question, do you need to replace all the bolts with the timing belt kit?
@vishnusuresh17577 ай бұрын
great 💯💯
@patricka.88336 ай бұрын
Hi, does the Ford Mondeo limousine 03/2003 1.8 110ps has a timing chain or belt?
@Campbell1.4 ай бұрын
Great Video. If I took my Mondeo to Ford for the same job, how many hours would you estimate. Thanks
@MrWhynot657
2 ай бұрын
2 or 3
@Vanadeo4 ай бұрын
How did you get the crankshaft pulley bolt off? .. I've read some horror stories about that snapping off in the block.. .Now I'm paranoid it's gonna happen to me when I do this in a couple weeks time.
@Vanadeo
2 ай бұрын
Conclusuion.. I bought a Map torch and heated it up just enough to melt the loctite and not the crank seal.. came straight out.
@hamlet25542 ай бұрын
Hi Baz. How many hours of labour would go into this belt replacement procedure (from your end)? Thanks in advance.
@leesaville31706 ай бұрын
What would jib cost to be done??
@riskfreesolutionsforbusiness4 ай бұрын
you dont Have to LOCK the flywheel to remove the pully bolt "first time"?
@DexterXxX4 ай бұрын
That is the diameter of that locking pin by the starter motor thanks
@MadMurdock693 ай бұрын
Hi,anyone know what the time schedule is for this job?
Пікірлер: 26
Hope you’re feeling better soon … how you keep pushing yourself when feeling so rough , is incredible 👍😁
Great video. Clear, concise and no 12 minute preamble like some channels. This is the 1st clip I've watched from this channel and I've subbed as a result, keep up the good work mate 👍
once again Baz great video you make timing belts so easy
Just replaced my factory original timing belt after 16 years and 177k haha It was still in operational condition, but had a few cracks developing and the water pump was weeping in the same place as this one, with a lot of dried coolant starting to build up below it... The cam chain rattles for roughly one second on start up, but I've heard this is relatively normal. I will add that the timing belts pretty much never fail in these. They have a rare occurrence where the belt will strip the teeth, but this is caused by the hp fuel pump locking up on the opposite end of the camshaft.
Nice work, with good advice. Videos to the point and not too much waffle
Amazing work as always! Hope you feel better soon buddy!
Baz i had the flu the other week mate its a,killer looks like the same set up as the Ford kuga 20lt diesel video's you done good job
Hi Baz I have a leaky front crank seal is there much more work involved after timing belt is removed, crank pulley pulls off easy enough from my experience, love the content keep it up 😊
@bazmeredith
13 күн бұрын
Straight forward buddy and thank you 🤙
Don’t worry, you’ll see the Peugeot/Citroen TU 1.1 and 1.4s, I’ve had the belts break lots of times, one time I got away Scot free without bending the valves but the head gasket did fail a few thousand miles later
Done a few of these not nice getting crank locking pin in lot easier on 1.6 on front reluctor ring
howzit Baz, nice one i have been wondering here, my Ford Focus tdci need a foot on the gas pedal to idle otherwise its wont idle instead it will die could it be the timing being off?
tried heat &air wrench pully bolt wont move .thinking if i put car in gear break on will i get away with not having lock fly wheel up or is that asking for trouble?
Question, do you need to replace all the bolts with the timing belt kit?
great 💯💯
Hi, does the Ford Mondeo limousine 03/2003 1.8 110ps has a timing chain or belt?
Great Video. If I took my Mondeo to Ford for the same job, how many hours would you estimate. Thanks
@MrWhynot657
2 ай бұрын
2 or 3
How did you get the crankshaft pulley bolt off? .. I've read some horror stories about that snapping off in the block.. .Now I'm paranoid it's gonna happen to me when I do this in a couple weeks time.
@Vanadeo
2 ай бұрын
Conclusuion.. I bought a Map torch and heated it up just enough to melt the loctite and not the crank seal.. came straight out.
Hi Baz. How many hours of labour would go into this belt replacement procedure (from your end)? Thanks in advance.
What would jib cost to be done??
you dont Have to LOCK the flywheel to remove the pully bolt "first time"?
That is the diameter of that locking pin by the starter motor thanks
Hi,anyone know what the time schedule is for this job?
belts are made to do 200 th miles.. ford..