Life saver! PSA for other people: this also works on fiestas without the additional steering audio control module

Thank you for the video. Saved me a lot of time figuring out how to dismantle everything. I would imagine that mentioning fiesta model (MK6) in the title might be helpful for future watchers.

@eddiesfixes

Жыл бұрын

Glad it helped. I think I'll take your advice and edit the title. Cheers

Thanks a lot sorted my sons mk6 fiesta (2007). . On mine the screws were T15 torx.

Just done this now using your instructions. The steering lock is working now too so i did not have to change lock cylinder after all. Starts first time now. Cheers.

@eddiesfixes

Жыл бұрын

That's good to hear. Glad it helped 😃

Sorted my problem. Thanks. 1 comment - you don't need to remove the top cowl and have the difficulty of getting the rubber back in the slots. Once you got the bottom cowl off, the top will fold back out of the way. Saves some scratting. Put a mirror behind to see the slot to release the audio control - I have some of my wifes old make up compact lids which are ideal. Whole job from start to finish took less than 30minutes.

@eddiesfixes

Жыл бұрын

Nice one 👍

After watching this Eddie I'm gonna have a go , cheers

Thank you so much the mk6 st is back on the road! Was an intermittent issue but fires up 100% of the time now can't thank you enough.... Was funny the things that took you longer than usual took me seconds the things that took you seconds took me 20+ minutes! The actually switch was stuck had to bash it off with a flat head 🤣🤣! Thanks again liked and subbed

@eddiesfixes

Жыл бұрын

Glad it helped, yeah I was fiddling with the steering wheel stereo controls for a bit 😆 I try to be delicate with the flimsy plastic bits.

@TopEndBen

Жыл бұрын

@@eddiesfixes haha never ending I'm exactly the same always feels like somethings going to snap especially with old clips and previous owners lol!

Thanks so much this helped out alot 😊👍

You Save my ass just today. My Festa is alive again! Thanks 😸

@eddiesfixes

Жыл бұрын

Thanks, glad it helped 👍

Thanks, that helped me fix my daughters car.

@eddiesfixes

6 ай бұрын

Glad it helped 👍

Gracias por tu video me ha ayudado mucho

@eddiesfixes

8 ай бұрын

Me alegro que haya ayudado

Thanks, changed mine has I have a dead spot when turning over littrally now and again so thought I'd go cheaper route first,I did put a new battery on late last year but still happening now and again, worth a punt for how cheap it was and also mine was very worn key would wobble around quite bad now it's %100 better,the 3 torx screws were awkward typical ford lol

@eddiesfixes

3 ай бұрын

Glad to hear mate 👍

Thank you, all sorted, 16 quid !

@eddiesfixes

Жыл бұрын

Good to hear 👍

Interested in MK6 videos would love to see the inlet manifold removed got PVC pipe issues atm

This video is a Life saver for me. I just could not figure out why my fiesta mk6.5 was more dead then alive. It turns out that the ignition switch is faulty.... The whole dashboard stays black when i turn the key in the ignition position. Then i found that if i pushed it a little more into the starter position the dash would come up, wait a few seconds and i could start the car .. But there is a sweet spot , which is hard to find, and this the point between failure and success. I can find it, but my wife not and is unable to start the car. The Fiesta is at the repair shop now, hopefully tomorrow they can install the new switch before 17:00, if not i pick up the car and pay for the new switch and install it myself.

@eddiesfixes

7 ай бұрын

Thanks. I'd be curious to know how much the price was to have one fitted at a garage.

@johngroenen

7 ай бұрын

@@eddiesfixes i'll keep you posted. They charge me €18,30 without tax for the switch. By tomorrow i will know how much the labour was..... Just like some other reactions, it started with the immobilizer blinking fast, random. In the spring/summer no problem at all, fall and winter the gremlins return. But now with the dash staying black, or come up after a few seconds.... So i hope that the switch is the problem. Car is 17 years old, 190.000 km

@johngroenen

7 ай бұрын

@@eddiesfixes well, it took a bit longer then expected, but the Fiesta is back home. Ignition switch replacement set me back €60 in total. Tax is 21%, switch was €18,30 ex taxes, labour was €25 ex taxes. So there you go. This was not a Ford dealer, just a small garage which do all brands.

@eddiesfixes

7 ай бұрын

That sounds reasonable. Thanks for letting me know.

Hello thank you for the video could you tell me whereabouts you got the ignition switch from please? I've just looked on eBay but couldn't see any.thanks

@eddiesfixes

9 ай бұрын

I got mine from ebay, try searching by year or which mark/ revision you have. Sometimes they don't appear when searching by reg. You could always try onlinecarparts or eu-spares. They're about the same price on there too.

I think i may have the same issue. I have to hold the car key hard all the way round and keep it there giving it a wiggle at the end but dash lights go off and engine does not turn over. On the second attempt, it usually starts but engine and dash lights turn off by themselves very quickly. On third attempt if I give it a bit of gas, the engine starts and I have never had to press the gas pedal before to start this car. After that our 08 Fiesta mk6 tdci drives fine. In addition, my car key feels really loose in the ignition barrel and steering wheel does not lock when taking the key out. Do you think I need to replace the switch and the ignition barrel together to get everything working again. Great video by the way.

@eddiesfixes

Жыл бұрын

It sounds like it could be. If you have an extra pair of hands ask someone if they can listen for a click from the starter motor (the starter solenoid) when you try to start the car. If there's no click then I would imagine it would be the ignition switch at fault. It seems to be a common fault with them. Also regarding the ignition barrel, if the key seems loose then a new barrel would help and I believe it could resolve the steering lock issue, if not it could be an issue with the steering lock pin. Just bear in mind if your key fob battery runs out then you won't be able to unlock the car with the new key without changing the locks in the doors too or keeping the old key with you.

Thanks for the video. Curious as to what symptoms you had before changing? Every now and again my fiesta turns over extremely weakly and it’s confusing me as it’s got a new starter and battery. It’s hard to describe but it’s almost like it gives up. Thanks

@eddiesfixes

Жыл бұрын

I would say have a look at the chassis earth, make sure it's tight and no rust or corrosion on it. Also check the battery terminals and starter live just to make sure they're tight too. If it starts on the key every time then it's probably not the ignition switch at fault.

@eddiesfixes

Жыл бұрын

It's a cheap fix changing the ignition switch so there's no harm in ruling it out tho.

@Ben-bu2jg

Жыл бұрын

@@eddiesfixes thanks a lot for replying. Where is the chassis Earth located? I’ll have a look at that later. It’s just weird because it’ll do it very randomly like once every 70 starts and often if it’s been hot.

@eddiesfixes

Жыл бұрын

@@Ben-bu2jg if you follow the battery earth it should lead to the earth ring terminal with a bolt on the chassis, use a scotch brite pad or something similar and a bit of wd40 to clean the earth ring terminal, the bolt and the part of the chassis that the earth contacts. There should be another earth cable from the chassis to the engine (you may have to do a quick google to find that one). If you do the same for this too then you can eliminate any earth issues as the starter motor is earthed through the engine earth.

Hi, great video when I try turn the car on I do hear the click, however it occasionally starts. Could this be the ignition switch as I replaced this only a few weeks ago. The mechanic told me it was an electrical fault.

@eddiesfixes

Жыл бұрын

Thanks. does it click or start every time you turn the key to start. Does it try to turn over or just click? I would check terminal connections first as it doesn't cost anything to check, ie battery terminals, engine earth and starter terminals. Just make sure there's no movement in them, good earth connection and they're all tight. It does sound like it's possibly the battery or the starter motor at fault. If you have a volt meter try to check the voltage of the battery when it's not running. It should be around 12.6 - 13v.

@eddiesfixes

Жыл бұрын

Also. It would be worth checking if the click is from the fuse box or the starter motor. If you have an extra pair of hands you could ask someone to listen for the solenoid click on the starter motor. If the click is from the starter motor then it's likely there's an issue with the main live to the starter motor, an engine earth issue, a faulty battery or faulty starter motor. I hope this helps.

Hi what fault would be for firesta 2007 1.3 petrol, after fast flash its like 6 slow flash pause than again 6 slow flash and just repeating same pattern?

@eddiesfixes

6 ай бұрын

Hi, i've found a video another youtuber has posted that may be helpful. Sorry I'm not as clued up with the codes. kzread.info/dash/bejne/Yp92vMd7ksWfgLA.htmlfeature=shared

great video mate. did this issue when starting cause the immobiliser light the flash quickly?

@eddiesfixes

Жыл бұрын

Not that I remember, it shouldn't cause the immobiliser to flash quickly as all you're removing is a switch that feeds the live to ignition components and to the starter.

@eddiesfixes

Жыл бұрын

It sounds like it may be linked to the immobiliser. I've found a video that may help to read the immobiliser code. m.kzread.info/dash/bejne/Yp92vMd7ksWfgLA.html

@laverick12

Жыл бұрын

Thank you for the reply and once again it is a great video. I had trouble getting the cover off until you showed me how.

@eddiesfixes

Жыл бұрын

Thanks mate, glad it helped 👍

@PaulSmith-bn8gt

Жыл бұрын

Laverick I am having the same issue with the flashing Immobiliser light.but gonna try a switch first...BTW Very helpful watching this , thank you 👍

Graziiieee dall italia

@eddiesfixes

6 ай бұрын

nessun problema 🙂

I had this problem with my fiesta the other day message on the dashboard saying engine malfunction tried again after 5 mins and the car started up

Great Video how! How can you tell the starter motor is getting no power? My car is having similar starting issues where if you cycle the ignition or leave the key in the on position for 30 seconds it will eventually start.

@eddiesfixes

Жыл бұрын

Hi, if you hear the starter click (the sound of the starter solenoid engaging) when you try to start the car then there's power to the starter motor. My partners fiesta wasn't getting power to the starter solenoid so you couldn't hear the solenoid "click". The battery was fine, so I thought it was likely to be a poor engine earth, loose wiring terminals on the starter or the ignition switch. I hope this helps.

@chriss2410

Жыл бұрын

@@eddiesfixes Thanks Eddie, really kind of you to reply so quickly. I have ordered the switch and will try that first.

@eddiesfixes

Жыл бұрын

@@chriss2410 no worries. It's certainly worth a try and it sounds like it might be the switch. They're usually pretty cheap to buy. I think I found one on ebay for around £15. Another thought would be to check the immobiliser light goes out when you turn the key to ignition, which would rule out an immobiliser issue.

@chriss2410

Жыл бұрын

@@eddiesfixes Hi Eddie, thanks for uploading this video. The switch cost £8 from Amazon and repaired the fault. I saved £150 on the garage bill. many thanks!!

@eddiesfixes

Жыл бұрын

@@chriss2410 glad to hear mate 👍 cheers

Hi nice video, I have similar problem. Try to turn on the car but it was at first like rapid flashing of immobilizer, red dot light, but manage to start after couple of minutes. Now its like the key is loose in ignition and moving the key have effect weather there is contact or not, like there is delaye contact when turning the key. Is the soultion in the video same for this problem as well?

@eddiesfixes

6 ай бұрын

If the immobilizer light is flashing with the ignition on then that sounds like it may be a different issue but if you have £15-20 spare to rule out an ignition switch fault then it wouldn't hurt to replace the ignition switch first.

@PassionofPunjabi

4 ай бұрын

Hi yours problem is solved now because i have same problem

@nikolamilenkovic-cd5cs

3 ай бұрын

@@PassionofPunjabi No its not solved. It's in fault from time to time, not always, so it does not bother to much. Have you fixed it?

I have a mk5 I can turn the key first click radio goes on Next all the contact lights should go on but this does not happen. No lights come on. No start possible. Could this be the same?

@eddiesfixes

4 ай бұрын

When you try to start it is there any click noise from the relay box in the engine bay or from the starter motor? Also has the battery got adequate charge (approx 12.6v)?

@eddiesfixes

4 ай бұрын

It could be the same issue. It may be worthwhile checking the wiring at the ignition switch with a volt meter just to be sure.

Would you recommend disconnecting the battery before doing this?

@eddiesfixes

5 ай бұрын

I didn't in my case but I would imagine it's recommended.

My cluster doesn’t come on straight away when I start it could this be the reason.

@eddiesfixes

Жыл бұрын

It sounds like that may be a different issue. I would suggest checking and changing the fuse for your cluster. This might help: www.google.co.uk/url?sa=t&source=web&rct=j&url=fuse-box.info/ford/ford-fiesta-2002-2008-fuses-and-relays&ved=2ahUKEwiUmbTAqK_9AhWiR0EAHQppA6AQFnoECCwQAQ&usg=AOvVaw2x12UsJCtGQNqKJQAPHXhA

@mr_zsfez3278

Жыл бұрын

@@eddiesfixes thank you so much for your response I’ll try that.

how can we replace a ignition switch for ford fiesta 2008

@eddiesfixes

2 жыл бұрын

It should be a similar process. I've found a video by another user on a slightly newer fiesta which may be helpful. m.kzread.info/dash/bejne/pZ9tttBtqcSyhNI.html

@eddiesfixes

2 жыл бұрын

You may have the mk7 fiesta (2008 - 2013). This video is for a mk6 fiesta but the process should be similar.

@Joanml14

9 ай бұрын

How can we replace ignition switch ford fiesta 2014?

Hi, i just changed the same part on my Fiesta, however now the immobiliser engages every time i try to start it. I have to disconnect the battery before any dash lights come on again. Any ideas ?

@eddiesfixes

6 ай бұрын

That does sound like an unusual issue. Did the issue start straight after fitting the ignition switch. Could you have disturbed any of the immobilizer ring wiring when removing/ refitting the steering wheel cowl?

@te8469

6 ай бұрын

Thanks for your response I don't think so, just plugged everything back as normal I will check though I did change the barrel at the same time, might this have something to do with it? (I did change the key fob back to the original)

@eddiesfixes

6 ай бұрын

There is a chip in the key fob (in the original key). You'll need to transfer that to the new key too as the immobilizer ring will still be coded to the original key fob chip.

@eddiesfixes

6 ай бұрын

Just reread your message. It sounds like you've transferred the fob to the new key. Did you open the fob up at all.

@te8469

6 ай бұрын

@@eddiesfixes Hi Eddie, thanks for the response I transferred the fob to the new key, but didn't open the key or change the chip Perhaps Ivve knocked the wires in that case Is there a way of resetting the ignition switch?

defo mk5 not mk6?

@eddiesfixes

7 ай бұрын

I think there's a little confusion with the fiestas because of a facelift part way through. I don't know the whole history but this is my partners car which is the fiesta made between 2002-2008 if that helps.

@willdatsun

7 ай бұрын

not clued up on Fords but i think thats a 6. (same as my friends 2007) @@eddiesfixes

@eddiesfixes

7 ай бұрын

@@willdatsun it could be. There does seem to be some conflicting info online. I've just gone by info from Parker's.

So it doesn't need to be programed by computers or something just plug and play 🤔

@eddiesfixes

Жыл бұрын

Yeah it's just plug and play, no programming needed on these fiestas.

8:44

Thanks, camera man should be fired 😅

@eddiesfixes

2 жыл бұрын

Haha, glad it helped. I'll forward your comment onto the misses 😆