FlySky FS-GT3B radio control & GR3E receiver how to video tutorial.
This video tutorial explains how to set the FlySky FS-GT3B radio control & GR3E receiver along with brief explanation of each property. This tutorial covers:
1. Highlights 0:14
2. Which plug to which channel 0:19
3. Steering wheel and throttle in the radio-controller 0:24
4. Model Naming 0:43
5. Reverse 1:19
6. End-Point Adjustment (EPA) 1:41
7. Trim 2:42
8. Exponential (Expo) 3:17
9. D/R (Dual Rate) 4:11
10. Brakes 4:52
11. ABS 5:23
12. Binding the receiver to the radio-controller 6:45
13. Fail-Safe 7:42
If you liked my video, please do me a like.
Thank you for watching :)
Written, videoed & photographed by E.C.
Music credits:
Mars & stars by Dan-O at danosongs.com
Palms rise by Dan-O at danosongs.com
The owl named orion by Dan-O at danosongs.com
SEO strategic keywords:
binding, fail-Safe, fail safe, reverse, epa, end point adjustment, trim, expo, exponential, D/R, dual rate, brakes, ABS, FS-GT3B, FSGT3B, FlySky, FS-GT3B, radio control, GR3E, receiver, video, tutorial, youtube,
fs-gt3b,
flysky fs-gt3b,
flysky fs-gt3,
fs-gt3b review,
flysky gt3b,
fs gt3b binding,
fs gt3b receiver,
flysky radio,
rc controller,
fly sky fs-gt3b,
flysky receiver,
flysky rc radio,
fs-gt3b 2.4g 3ch,
flysky fs-gt3b 2.4g 3ch,
fs gt3b mod,
flysky gt3b review,
flysky rc,
gt3b,
2.4 radio control,
futaba rc,
spektrum rc,
fly sky 2.4ghz,
flysky transmitter,
fly sky 2.4,
flysky 2.4ghz 3ch,
2.4 ghz radio control,
flysky 2.4g,
flysky gt3b receiver,
flysky fs,
flysky remote,
gt3b receiver,
rc car controller and receiver,
flysky fs-gt3b review,
2.4 ghz radio,
rc car transmitter and receiver,
2.4 ghz receiver,
fly sky gt3b,
remote control helicopter,
flysky fs-gt3b digital 3ch 2.4ghz,
fly sky gt3,
best 2.4 ghz rc radio,
radio 2.4ghz,
2.4 ghz 3 channel radio,
3 channel radio control system,
rc receiver,
rc system,
trans mitter,
flysky fs-gt3b receiver,
fs-gt3b manual,
gt3b flysky,
gt3b radio,
2.4 ghz rc radio,
flysky 2.4ghz,
flysky fs-gt3b 2.4ghz,
2.4 ghz rc,
fly sky fs-gt3,
3 channel radio,
rc radios,
rc transmitter,
2.4ghz radio system,
flysky gt-3b,
remote controlled,
rc car radio systems,
rc receivers,
rc radio systems,
2.4ghz rc controller,
rc radio system,
rc car receiver,
cheap 2.4ghz radio,
fs gt 3b,
sky fly fs-gt3b,
fs gt3b fly sky,
rc 2.4ghz,
flysky 2.4,
radio control 2.4ghz,
rc radio receiver,
rc controllers,
rc radio systems reviews,
rc radio and receiver,
radio control receiver,
futaba 2.4 ghz,
flysky transmitter review,
2.4 ghz transmitter,
digital radio rc,
fs gt3b binding,
radio control fail-safe,
radio control fail safe,
remote control fail safe,
flysky fs-gt3b setup,
FlySky video,
FlySky video tutorial,
GR3E,
Пікірлер: 206
Excellent, thank you. Finally got my rc car going thanks to this tutorial. Much appreciated!
I look forward to mine arriving now i have this video to set it up perfectly 🎉🎉🎉 thanks bud
Thank you...I have this controller for my 30cc buggy....I actually didn't realise it had so many adjustments....what an excellent tutorial ...great vid ...
Hi Corey, You are welcome, and thanks for your feedback; I made a lot of effort to make this tutorial as informative and practical as I could. I don't work for the company. I bought this radio-control for my R/C car, learned its functionality and liked it. Then I decided to pass on this knowledge, so it would be easier for others to use it.
Thank you for making this and posting it. The instructions are very clear and easy to follow.
Glad to find this video. Already fried one esc when I first did it without searching up a video on how to do it for the first time when setting it up. Appreciate the great work that has been done in making the video.
@eyal-carmi
Жыл бұрын
I appreciate your feedback, thank you.
A VERY well done video, as good as a manufacturer could do. Congrats and thanks!
Best tutorial Video on how to progam your transmitter and receiver I have seen. Thank you for the Vid.
@eyaleyal8441
3 жыл бұрын
Thanks for your feedback. I am glad it could be of help to you.
Very nice video and smooth i can understand every word , very very good job. After this video i will buy this this flysky.
actually enjoyed the very good tutorial .. no waffling on , just precise instructions . well done mate ..
@eyal-carmi
9 жыл бұрын
Daz Brown Thanks
@jordanpopo9693
5 ай бұрын
If only everyone culd get a point across like this. For some reason i struggle to understand more people every day. As if they are all turning in to the same robot or something. They open there mouth and out spills the nonsense. Surrounded by idiots i always say 😅
Finally... Straight forward instructions. Thanks!
Thank You so much for making this video. I have been having trouble trying to figure out how to program this transmitter. 👍
Hi Angel, The radio-controller has 10 model numbers to choose from (Each model number lets you adjust the settings of each property and then save those settings to that model) . You can reset the values of all the properties of a specific model number by: 1. Turn on the radio-controller 2. Choose the model number whose values you which to reset 3. Turn the steering wheel right, and while doing so, press the back button. You should hear a high pitch sound (I had this sound).
Thank you. The video is concise and very helpful. It helped to fix a problem I created by misprogramming ABS. ABS is very hard on the drive train for my electric cars, maybe is more useful on gas engines. For my electric car, I turned OFF. Excellent video !
@eyal-carmi
7 жыл бұрын
A real ABS system has sensors on each wheel to get rotational speed feedback. With that feedback it regulates the braking system of that wheel accordingly. I am not sure this remote control - receiver is that versatile. You need that ability in the RC car as well. As I understand, this abs function is simply pulsating the brakes with an option of 3 modes - slow, normal or fast pulsating.
This was SO HELPFUL! Thank you thank you.
Yes, it was a very good tutorial. I learned what the set button on the receiver does.
Amazing!!! Best how to ever!!! Thank you 🙏 TRX 4 Sport and Traxxas Maxx.
Clear and well explained. Thank you, this has helped me a lot!
@eyal-carmi
10 жыл бұрын
Thanks, glad to hear that.
Excellent tutorial!!!it helped me out a lot.
YOUR VIDEO IS THE BEST ON THIS TRANSMITTER
Thankyou for the guide. Appreciated.
Great video, helped a lot thanks for taking the time to post this.
Yes, it was a very good tutorial. I learned what the set button on the receiver.
Wow, this totally helped me! THANKS!!!!
Thank-you for this video. It has helped me alot. I am a beginner and have watched it a lot.
@eyal-carmi
7 жыл бұрын
I am happy to be of help. Enjoy your car.
best tutorial, thank you.
Best tutorial ever helped tons thanks!!!!
Thanks for making this video. It helped me alot
AWESOME tutorial! thanks so much
Thanks very much fantastic video, needed this as instructions not clear enough
Thanks a lot Eyal, I thought maybe that was it but wasn't for sure. That fixed my problem and I appreciate the help!.
@eyal-carmi
10 жыл бұрын
No problem, I'm glad it helped.
Thanks for the video, helped me out of simple jam. If you're set up is in reverse just do as he explains! 1:19...
Amazing clear tutorial
This Is got to be one of the best hi tec controller on the planet .. It works well with any scale cars and it looks awesome with very good price .. My baja runs great with this and I love all the features as well as easy trim control .. Very fast response as well
@marknickells6097
Жыл бұрын
I went through multiple Futaba systems, and paid "Through the nose, for long distance. " (About 1000 feet), and although cool. IT wasn't worth it. I was able to fine tune 4 models, with mixed results. I ended up paying $75.00 for a new receiver, after it got water logged. (FUTABA does not offer a water proof receiver. ) WHY? . If running boats; that's a must . Bottom line. FUTABA is a total rip off, and you're paying for the name, and a lot of stuff, you don 't need. NOW, that same 4 channel receiver, is selling for $119? THAT'S nothing short of theft. BUT, to the point. I have own 3 of the Fly SKY GT3B systems, and all have preformed flawlessly, and have massive range, and WATERPROOF Receivers , by Default, and depending on source, can be purchased for as low as $5. SO, what are the big names (Spektrum , and Futaba doing, to justify the extra cost? NOW on my second radio, I have had the inexpensive radio, linked to four boats, and a Dune Buggy. I don't understand , why people think, they have spend a fortune on a "Cadillac R.C system," when they can buy, a "Mini Cooper," that does the exact same thing? THE look on people's faces, is priceless, or almost shocking. (Can't believe it) ...... Anyways. I am going to recommend FLY SKY over any of the BIG Name systems.
One of the bset explation video, if not the best. it help me a lot. thanks from Puerto Ric and Merry Christmas.
@eyal-carmi
10 жыл бұрын
Thank you and Merry Christmas :)
@robertowillis3921
6 жыл бұрын
Jose Fernandez i
Very good video, very helpful..form that you get my sub. Thanks can't wait to get my new radio
thanks man. I resolved my difficulty
Cool video bro very informative thanks
Best tutorial on the flysky ever
@eyal-carmi
4 жыл бұрын
Thanks you :)
Many many many thanks man! I would get crazy before seeing this video.
@eyal-carmi
7 жыл бұрын
Glad to hear it. Enjoy your car.
Excellent quality presentation. Thank you.
@eyal-carmi
Жыл бұрын
Happy to!
Very helpful, thank you.
Thank you! I struggled a lot with the E.point adjustment
@eyal-carmi
Жыл бұрын
Happy to!
It helped me out a lot thanks a bunch
Good job bro...it's very useful..very nice..
Thanks, great video
Great Video!
thank you... it helps alot
This vid was vary helpful
got it, tks again, its working!!
Great video. Thanks!
@eyal-carmi
3 жыл бұрын
👍
Great vid I know how to work my controller now !! Thanks
@eyal-carmi
4 жыл бұрын
👍
Thanks Mate!!!
Good question. I have emailed to FlySky your question and will give you an answer as soon as they contact me back.
Good tutorial
You don't need the AA battery box, it was just easier for me to show the binding process with it. The receiver that came with the remote-control is already binded. If you need for some reason to bind it, follow these steps: 1. install the receiver - channel 1 to steering wheel, channel 2 to the ESC 2. Follow the binding steps in the video, with the exception: instead of connecting the AA battery box to channel 2, connect the ESC to channel 2. Everything else is the same.
Just got this rx thanks for the help
thanks a lot man.
@eyal-carmi
10 жыл бұрын
with pleasure
Glad to hear. Thanks for your feedback
@hardyb311
8 жыл бұрын
+Eyal C Why when i push throttle down it goes in rev? When i push throttle up it goes forward
@eyal-carmi
8 жыл бұрын
+hardyb311 look at this video 1:19
Thank you so much. I found this video very helpful for adjusting the end points. The manual is as clear as mud. I was having issues with forward speed with my newly built RC boat, which was due to the end point being set too low. I had no idea how that happened, but after watching this video I was able to max out the forward throttle end point. My boat now is very zippy. Thank you.
@eyal-carmi
3 жыл бұрын
That's great ! thanks for your feedback :)
i just burned my receiver and then i found your channel, have to get new receiver, thx
To add to this, if you position your throttle trigger while pressing the set button, the failsafe will set the throttle to where you are holding it with the trigger. I have no reverse so I pressed the set button while holding the brake on. Now the brake comes on if I turn off the transmitter or lose the signal.
Thank you.
Yes. Follow the instructions in my other video "Traxxas Slash Platinum 6804R recommended accessories ". In the "About" tab you will find the contents. Press "Installing the receiver 2:20". It will guide you through the process of how to install the new receiver (after you uninstall the old one offcourse).
Thanks alot
excellent language was very easy and everything was beautifully explained
@eyal-carmi
7 жыл бұрын
Thank you
nice video bro . thanks
hi. im a bit conffused about what to do with the reciever. do I just take out the old one currently in my car and place the new one in?
ok, so installed this reciever in my slash, confused about binding...i dont have a little power box with AA batteries...do I plug a nimh w traxxas connector directly into channel 2 to bind? excuse my ignorance
Eyal C, do u work 4 the company? Because this is a very very good and informative tutorial!!!!! you did a very good job teaching me about this car... thanx alot man!!!
thank you
I can get it to steer but I cannot get it to go forward or reverse. How do i get it to move??
Can you explain how to change the ESC from a JJRC Q39 to GR3E with Flysky?
My car has no brakes it does when I go in reverse then drive but when I go forward then brake it goes in reverse??
I've got one car setup on on receiver and now the second one once bound just flashes after I've bound it. Doesn't seem to work at all
If i buy the same receiver like in this video can i create a new model memory? Sorry for bad English
Can I bind this receiver to a FS-GT5 controller?
Full Throttle RC, did you switch the ESC / Motor when you upgraded the radio? It sounds like the motor is running backwards, but Channel 1 is also reversed, so "forwards" still goes forwards but braking is messed up. You need to reverse Channel 1 and switch the motor direction. Braking is handled in the speed control, not the transmitter.
hey Eyal, I have a question 4 u... I noticed that my blue LED backlight on the receiver is not functioning, is there a setting that can be adjusted? I have contacted FlySky and it's been over a week and no response
Heyy.... great video!!! It's really hard to find people who explain this well. I know I'm a bit late but- I'm making an electric go-cart as a project and was wondering if I could connect this receiver to something that powerful (500w-1000w). The usual throttles that are used to control the go-cart take a similar input of 6v so I thought this could work. They also have one negative, one positive and one control wire and output ~1v to ~4 v (no throttle to full throttle). Can you measure the voltage output range of the receiver? connect the negative pin of the receiver to the negative of a multimeter and the control pin to the positive of the multimeter and test the voltage range with no throttle and full throttle. This would help me out a lottttt!!!! Hope you read this.
I'm having issues with the steering. To turn my RC left I have to turn the controller dial clockwise and to go right I have to turn the dial on the controller counterclockwise??🤔
@eyal-carmi
7 жыл бұрын
Hi, That is easy to handle. Watch the video - Reverse 1:19. You are welcome to look at the content. Each section directs you to the right time.
Helo.. how to connect winch and setup winch
when putting the model and name on the controller is it alright not to put model or name in controller?
hey, i have the exactly same receiver with yours. When i plug in a servo in channel 3 (for other purpose), the original servo that plugged on channel 1 not working anymore. when i trim it, it still can move, but i can't steer it. How should i solve this problem? Can i actually plug anything into channel 3?
@eyal-carmi
9 жыл бұрын
Hi,I haven't used the 3rd channel, but it seems strange to me that 3rd channel would affect the 1st channel. Regarding its usability, you can plug a servo or use it as a switch, but you might need some other accessories to apply it. Search for some videos regarding it. I found some mentions about people using a modified firmware to enable more capabilities including 3rd channel capabilities: www.rccrawler.com/forum/electronics/376715-flysky-gt3b-servo-winch.html Hope it helps.
I finally got around to setting up a second vehicle on this transmitter. I think I may have gotten duplicate receivers, or maybe it's supposed to work like this. I can control both vehicles with either profile. I assumed that switching from one profile to another would disconnect the transmitter from the previous vehicle. I purchased two extra receivers when I bought the Transmitter. Is it normal to be paired to two receivers on the same profile. It's not much of an issue since I would never be trying to drive both vehicles at the same time, but it can be an annoyance if I forget to turn the first vehicle off after the battery runs down, and then it recovers enough to respond to the transmitter when I switch to the second vehicle.
@eyal-carmi
4 жыл бұрын
Hi Larry, I would assume the same thing as you regarding switching from one profile to another, but different companies have different ways of doing staff, so you can never know for sure (unless they give that info). If you keep the following habit you won't have any trouble: ALWAYS TURN OFF OTHER RC CARS BEFORE TURNING ON ANOTHER. Just make it a habit :)
Can it use a rechargeable battery, and be recharged ?
My car has no brakes it does when I go in reverse then drive but when I hit the brakes when I'm going forward it goes in to reverse??
@Fats-yg1jd
6 жыл бұрын
mine does the same thing
No problem, When you get the answers, would you be kind to write them here (including the car model you have) ? Thanks
GD VID N1 WELL DONE , ;0)~
I just started using RC cars and I cannot bind my flysky. I have the exact same set up as you do in your video. I can bind it but when I remove the battery from the receiver and turn off and back on the controller, I lose the binding and receiver starts flashing again.. please help me understand what could be wrong...
@eyal-carmi
4 жыл бұрын
Hi, first let's make sure things are done in the right order. Binding wire is inserted to channel 3. The receiver must get power in order to do the binding. This can be done by the proper external battery (if you have such) inserted to the Vcc socket OR the power can be given by the ESC connected to channel 2. You must not use both. BE CAREFUL when binding if you choose to use the ESC connected, because the car throttle can run unexpectedly, so be sure to hold the car safely. The directions in the video worked for me, but let's make a change (According to page 9 instruction F from the manual). Follow the instruction in the video with the following change - remove the Binding wire BEFORE you remove the battery (or ESC) from the receiver. Only then remove the battery from the receiver. Tell me if that solved the problem. The manual can be found here: fccid.io/N4ZFLYSKYGT3B/User-Manual/User-Manual-1769993
i have a little issue with my flysky when i pull trigger get notheng but when ki push it frorword i the motor runns
@petertebo914
Жыл бұрын
but have a boat
Is it possible for the throttle servo not to work, by pressing a wrong button on control thanks.
@eyal-carmi
4 жыл бұрын
Hi Richard Baker, the question is not clear to me. Can you please rephrase or explain what you mean ?
Hi eyal i just want to know is that alright not to put the model and name?thanks
Thanks, channel 2 and channel 3 are sets to failsafe, i want to keep channel 2 failsafe and channel 3 unfilesafe, do you know how to do this? thanks shlomi
@eyal-carmi
7 жыл бұрын
Hi, according to the manual, failsafe works on the throttle channel (channel 2). I have no idea about the other channels. But, why do you want to cancel the fail-safe on a specific channel ?
Hi eyal i have a issue with my controller. When i got it the steering is backwards. I turn right and it goes left. Im new to this and was wondering if you would mind making a short video showing how to reverse it on the controller. A lot of people tell how online but when your new and don't know everything its still real confusing, thanks a lot.
@eyal-carmi
10 жыл бұрын
Hi afallenstar4u, I assume you have the FlySky remote controller ? If so, look at "Reverse 1:19" chapter in this video. This chapter demonstrate how to reverse direction on the throttle channel which is channel 2. The same idea applies to the steering wheel channel which is channel 1.
I am helping a friend who has upgraded his radio. When the throttle on the transmitter is in the neutral position the motor turns. Throttle trim does not go far enough to cancel the motor. How do I calibrate the ESC to the radio so the motor will stop when the trigger is released? thanks in advance Allen
@eyal-carmi
5 жыл бұрын
Hi Allen, did your friend set the fail-safe function first ?
@allenmoore9848
5 жыл бұрын
@@eyal-carmi we found the problem. It was the ESC needing to be trimmed mechanically to match. All working good now
Yeah on the video
i have this controller also,can someone tell me how to set my controller to idle my Jato 3.3.i can't get it started because it not idled up enough.thks in advance
@eyal-carmi
10 жыл бұрын
Hi meatdogg101, If I understand you correctly, the trim function should solve your problem. In the current video you can find how to set the trim function on channel 2 (throttle). If you are not familiar with the trim function, you should also look at my other video "R/C Car Radio-Control Basics" at the trim chapter - it demonstrates the effect of the trim function on the throttle channel (channel 2).
Hi good video, helped a lot! But why is my car reversing when I want it to go forwards and forwards when I press reverse? Help!?
@eyal-carmi
5 жыл бұрын
Hi ,You might have reversed it accidentally. Look at the video at 1:19 (talks about reverse)
How can u reset this controller