Always a wealth of information! Thank you Tim! Great timing. Im getting ready to setup flaperons on my freedom fox. Also great info on the order of the plugs, I always wondered about that battery terminal.

@TimMcKay56

Жыл бұрын

GPJ: All good, thanks for checking in! Tim

Thank you for providing me with detailed instructions on how to set up my Flaperons.

@TimMcKay56

2 ай бұрын

Thanks for checking in! Tim

As a beginner this actually makes sense the way you expain it. It seems a couple other videos I have watch skip over some of the most fundamental basics questions that I have. Thanks man.

@TimMcKay56

10 ай бұрын

Anytime! Tim

Excellent video. Thank you very much!

@TimMcKay56

5 ай бұрын

Thanks for checking in! Tim

Brilliant video . Such a clear explanation with nothing missed out . Thanks

@TimMcKay56

5 ай бұрын

Jonathan: No worries, thanks for tuning in! Tim

Thank you, so helpful! I’ve been away from RC for a long while and have kind of forgotten everything. I have a spektrum AR620 and a spektrum DX6E. I have the manual for both. But the manual for the AR620 doesn’t give you any hints at all about how to do this properly. Not even a guide to which pins for which servo. That’s just plain nuts. I’m setting up a Libelle DLG with flaperons and I had no clue how to do it. So you took me right through it and everything works perfectly now and thank you so much.

@TimMcKay56

4 ай бұрын

Skypix: Glad it worked out!! Tim

Vielen Dank für das Super Video. Das hast du gut erklärt. Das waren genau die Informationen die ich gerade gebraucht habe. Danke. Grüße aus Deutschland. Guten Flug

@TimMcKay56

Жыл бұрын

Copy!

Excellent Information on the General Use of the Computer Radio Function to program the separate Servos. I am just getting into 3D Printing Airplanes. I have yet to actually complete one; but I am learning a lot from your Videos and from Troy McMillan's videos. Eclipson, PlanePrint and 3DLabPrint have some excellent (even free) Model Plans. Thank you for the valuable tips.

@TimMcKay56

Жыл бұрын

12T: Thanks so much for checking in! Tim

Superb !!!

@TimMcKay56

8 ай бұрын

👍🏻😊 Tim

Great job Thank you

@TimMcKay56

2 ай бұрын

Thanks for checking in! Tim

Very cool.

@TimMcKay56

Жыл бұрын

😊👍🏻 Tim

Thank you

@TimMcKay56

9 ай бұрын

👍🏻😊 Tim

As always very informative Tim love all your videos. You take great care in making them very professional. I was wondering if you have considered building the Guillow’s Spirit of St. Louis I’m considering building one. Would like you consideration on this kit.

@TimMcKay56

Жыл бұрын

Don: Many thanks for checking in and your kind words. Yes, will add the Spirit of St. Louis to the build list! Tim

Hi tim, hi from melb australia..!!!

@TimMcKay56

Жыл бұрын

😊👍🏻 Tim

Thanks sir for the video. Very useful for us. I want to know if I could use flaperons when the 2 servos alierons go to the same port off the receiver. Thank you.

@TimMcKay56

7 ай бұрын

Very good, thanks! Tim

I agree about spectrum receivers I have tried some of the other cheaper ones and end up pulling my hair out trying to get them to bind but never had a problem with spectrum

@TimMcKay56

Жыл бұрын

Fully agree!! Tim

How about setting the flaps to work with the ailerons to make full width ailerons? Do both flaps and ailerons have to be on their own channel , as in 4 channels, or can the ailerons remain on a Y lead? I only have a 6 channel Tx and Rx

@TimMcKay56

Жыл бұрын

Patrick: Great question, not sure of how exactly to accomplish this! 🫢🤔 Tim

Hi Tim, Many thanks for your excellent info. I have tried it on the new XFLY Twinliner using a Spectrum 630 with SAFE. Once I disconnect one of the ailerons & into channel 6 the Flaperons all work after reversing the flap system but the right aileron does not operate in SAFE mode only the left aileron works in SAFE. Any ideas? Do I need to use a 'Y'Harness? Hoping you can help. Regards

@TimMcKay56

Ай бұрын

BAV: Apologies, but no blazing insights on this one. I am just not very smart on SAFE issues. Do give a try at www.RCGroups.com Seems like those forums know everything. Tim

@Bellairvideo

Ай бұрын

Many thanks Tim. I did try a ‘Y’ harness but does not like it.

Hi Tim. I just set up flaperons following your video with a DX6 and an AR630 receiver. After testing everything, I find that port 6 doesn't provide AS3X or flight mode to my left aileron. How can I fix this please?

@TimMcKay56

Ай бұрын

John, first I have heard of this. Any others? Tim

@JohnGillies-sh4gm

Ай бұрын

@@TimMcKay56 Hi Tim. I got it worked out. All I had to do was a factory reset of the receiver through forward programing on the DX6. Thanks!

@TimMcKay56

Ай бұрын

Yikes . . . well done!! Tim

Can you also do this on a dx8 gen 1 transmitter? Thank you.

@TimMcKay56

7 ай бұрын

CH: Not sure, but I imagine the menus would be pretty close. Try it out, see if it works! Tim

@capnhardway

7 ай бұрын

@@TimMcKay56 I'll talk to my expert club members. You said about fwd programming at one point, I know it doesn't have that.

@gordonmckay4523

7 ай бұрын

@@capnhardway Good luck! Tim

Superb !!!

@TimMcKay56

2 ай бұрын

Thanks! Tim