It works! Had the same sound thought heat shield like everyone else did. Thanks guys! I did have some white lithium in there added 20 some pumps of moly grease to the bearings and a handful on my splines of the driveshaft worth everybsecond drive line took maybe 30 mins wheel bearings about 1hr not bad super worth it. 2020 x3 rc rr. Had grease from chaparral motorsports good job chaparral!

Thanks for the video, just fixed my 19 XRS, the driveshaft was surprisingly easy to access like you said, great stuff, noise is gone!

Guys loved the video and I just bought me a X3 XRS Max RRS and OMG😎Fastest and most comfortable ride ever❤️

Wheres the link to the video that shows you where to mark the front drive shaft so you put it on correctly?

My son bought a brand new X3 turbo R 2 days ago. We went on a short ride today and this is the same rattle we heard also. Thanks for sharing the video and details on how to fix the issue.

@M3OffRoad

4 жыл бұрын

Thanks for watching. You wouldn’t think that all of that noise would come from something so simple. Use the heaviest grease you can find. If you have questions you can email me Ryan@m3offroad.com

My 2020 maverick sport max 1000r makes the same noise in lower rpm range in 2wd only. Still under warranty so taking it to the dealer in a couple days.

@M3OffRoad

3 жыл бұрын

Definitely the same problem for sure. They will install a set screw in the spline to stop it

Great video...so the rear drive shaft does not need to be marked like the front end? You just put the rear drive shaft as far as it can go into the trans?

@M3OffRoad

4 жыл бұрын

Yes you can put the rear on in any rotation. It’s only important for the intermediate in front of the carrier bearing to be in sync

2019 x3 turbo base here. It's not bad when cold but after running the machine for 20 min or so is this sound like a grind rattle type that comes in on a slow acceleration from a dead stop to around 3000 rpm and then goes away as you speed up? You can hear it like basically where the gear shifter is but sometimes sounds like from the back to? 300 miles on mine. Still under warranty I wonder if leaders rpm in Kalamazoo has a TSB on it?

@M3OffRoad

4 жыл бұрын

Yep that’s it for sure. Pull the side panel and hold the driveshaft while throttling the engine in neutral. Sound should go away when you put pressure on it. Grease the splines it will go away. If it’s under warranty service will do it for free.

@csxjim

4 жыл бұрын

@@M3OffRoad just dropped it off at leaders rpm Kalamazoo for its 1st service and inspection.. Gave them a heads up. We will see what comes out of it. I told them the sound doesn't come into play until the driveline and everything is up to hot running temp.

@csxjim

4 жыл бұрын

Thanks again. They heard it and exactly what you said. Hardly any grease on both splines. Packed it on w marine grade grease. Problem solved. Warranty covered.

Do you like the charge tubes? I just got some. Did you do a BOV on it?

@M3OffRoad

3 жыл бұрын

Yes we all run the charge tubes and blow offs.

I get rattle when I hit the breaks i hear it in the rear, I jacked up my 2020 can x3 and I spin the rear tires and hear it coming from the diff/rear axles

@M3OffRoad

4 жыл бұрын

that is the clutch ratcheting when the brakes lock. its normal nothing to worry about

You can see my pickup day and some upgrades I started in at my channel and triple black❤️❤️

What flaps do you have on it? My trailing arms are rock blasted raw already and its only got 45 miles on it.

@M3OffRoad

3 жыл бұрын

Rockbloks but even that won’t help. Our trailing arms and radius rods are sand blasted. All you can do is put some WD or similar on them to keep them rust free.

Mine started doing that and the whole rear end is Jerking real bad at very slow speeds..... once you speed up though it stops..... it makes a pretty bad clanking noise also and I only have 20 miles on mine...... haven't even rode it hard yet..... not sure if it's the same problem

@bryancardona8213

3 жыл бұрын

What did you do to fix it mine is doing the same thing

How long does this last? Wouldn’t it be better just to get a greasable carrier bearing?

@M3OffRoad

3 жыл бұрын

Unfortunately its not the carrier bearing, it is the spline connections on the drive shaft. We do not touch the carrier other than to remove the shaft.

@Mike-mn9xo

3 жыл бұрын

M3 OffRoad - MI Mud Masters is there a permanent fix to this ?

What type of grease exactly did y’all use ?

@lenhammermeister1287

4 жыл бұрын

Use a good waterproof grease for marine application it will last longer. Thanks for the question!!!

@M3OffRoad

4 жыл бұрын

The thickest you can find. Light grease will not help for long

Is this the known 5k rattle fix? Mine will rattle in park just revving and at 5000-5200 it’s horrible

@M3OffRoad

4 жыл бұрын

Yes this is definitely the rattle you are hearing. You wouldn’t think it but it is. Thanks for watching!

@DUNEATV

4 жыл бұрын

Did you grease it? Did it fix the noise?

hey guys uploaded this video again or im tripping . Good video 👍🏼.

@M3OffRoad

4 жыл бұрын

LOL.. Yep we uploaded again due to the fact that I had to drop our old opening scene. Good catch!!

Nice tattoo! Saint George? Saint Michael?

@M3OffRoad

4 жыл бұрын

Yep one on each. Good Catch! Thanks for watching

Don't tire machine down with the body Tire down as close to the tires as possible or preferably Tire strap

Hey cool video. How did you end up getting a tattoo in Russian. Lol

@M3OffRoad

3 жыл бұрын

I was brought up Russian orthodox, my two patron saints are Michael and George. They have definitely been looking over me with all the crazy stuff I’ve done. Paying my tribute

same thing in 2021 commanders too.

@M3OffRoad

3 жыл бұрын

Ugh.. I haven’t heard it yet on my new XTP but we will see. Thanks for watching!