Thank you for the excellent tip. It worked for me and, now it starts more easily, I love my Ryobi trimmer!

@HomeGaragechannel

4 жыл бұрын

Thanks for the comment I appreciate it

Good job explaining everything about the engine running rough. I moved about 5 years ago into retirement. I stashed my Ryobi weed wacker away in my wood shop and recently saw it sitting in a corner looking very good. I had not run it for the last 5 years. It started on the first pull for 2 years about 7 years ago, and now I am replacing the same parts as you did on yours. Before I moved it ran like a fine oiled machine hopefully I can get it to run like that again. I will let you know after I finish replacing little stuff on it. It is heavier than I remember. Talk to y0u soon brother. Thanks for the video, you gave me inspiration to fix it again.

@HomeGaragechannel

4 жыл бұрын

i wish the best of luck. If it doesn't work out consider replacing the carb.

Fantastic video! Great step by step explanation of a carburetor repair for a Ryobi string trimmer. I'm currently fixing 2 Ryobis, a 30 and a 25 and both carbs are pretty similar to your video but the 25 doesn't have hi/lo screws for carb adjustment. Love the spark plug analysis and compression test, first time I seen those on youtube.

@HomeGaragechannel

4 жыл бұрын

Thank you for the comment I appreciate it.

Great video : ) I bought my Ryobi "Extend" trimmer 6 years ago. It's been a very reliable tool for edge trimming, weed trimming, Blowing off the sidewalk, and roto-tilling. I finally had to rebuild the Carb and replace the fuel lines as they rotted apart just this year (2021). Still works AWESOME... I would highly recommend Ryobi products.

@HomeGaragechannel

3 жыл бұрын

thank you for the endorsement of Ryobi products

I have 3 of these, only 1 that I bought new. Have had constant trouble with these. Thanks for sharing.

@HomeGaragechannel

4 жыл бұрын

Thank you for the comment I appreciate it

Thanks for this video. I've had a 4 cycle C430 Ryobi for about 12 years and up until recently it's worked like a champ & taken a few beatings along the way. It was starting but then dying while running. I replaced the fuel lines because the filter came off, then I had to replace the oil pan because it cracked, then it would start but die in idle. I was about to throw in the towel and just buy a new trimmer but I'll try the carburetor first.

@HomeGaragechannel

5 жыл бұрын

Yes I would swap a new carb in first. If the fuel filter came off then some debris may be clogged in the inlet screen inside the carb. Thanks for the comment

I love to problem solve these small gasoline engines. Your video content and production is EXCELLENT.

@HomeGaragechannel

4 жыл бұрын

thanks for the comment I appreciate it

This video saved me! Thank you. I hate asking for help and this walked me through everything I needed to work on.

@HomeGaragechannel

3 жыл бұрын

No problem and thanks for the comment

I have a Ryobi but can’t recall the model. Same problem. Worked great then would start but not continue to run when throttled up. Then would not start at all. Thanks for posting this video. I’m going to try everything you did.

@HomeGaragechannel

5 жыл бұрын

Excellent I hope it works out for you.

What a great video. I am not sure if I will have any success with my trimmer, but I now have a lot of great information to work with.

@HomeGaragechannel

3 жыл бұрын

You're hopefully better prepared than before. Thank you Tony M.

Superb video! I couldn't find my mixture screw(s) for nothing until I saw this video. I didn't have a Pac Man screwdriver so I used an amphenol (electronics wire harness) screwdriver instead. It's a hollow type screwdriver if you're not familiar with it. Now it runs as crappy as it always did - but at least it runs! This is my second Ryobi weed whacker. There's just one problem. My first one was 4 cycle. After 1 or 2 seasons I thought I'd change the oil in the new Ryobi. That's when I figured out the new one was a 2 cycle. Now you know why it runs like it's got a "miss" in the engine. To its credit , it still runs after many years of use. I guess I'd buy another one if needed. I've only had to replace the string hub once as well as one or two bump knobs but that's natural wear & tear.

@HomeGaragechannel

4 жыл бұрын

excellent work. Very resourceful. Thank you for the comment I appreciate it

Fantastic VIDEO I nearly threw trimmer out. I actually just got it going after 7 yrs sitting in da shed. A big Thankyou for this video.

@HomeGaragechannel

3 жыл бұрын

you're welcome Frank Caccamo

Helped me figure out the stalling on throttle. i dremeled some grooves into the pacman screws and now it runs like a beast. cheers.

@HomeGaragechannel

4 жыл бұрын

Yes that works very well too. Thanks for the comment I appreciate it

Yes used Ryobi trimmers in the past and now have bought 4 Ryobi trimmers as non runners and got them all going again

@HomeGaragechannel

4 жыл бұрын

Excellent. You seem to like them. Thanks for the comment I appreciate it

I have basically the same unit (EX26). It takes many pulls to start with choke on. I'm not handy but this video was very helpful. Mine is several years old and I have not maintained it. I like it because of the many attachments that can be used with it.

@HomeGaragechannel

4 жыл бұрын

give it a shot and i understand how you feel about the attachments

Well done, and thank you for saving me some time. I have had my Ryobi for over ten years. The PacMan Tool saved the day. One thing I like about the Ryobi is the multiple tools you can use with it. I have the Weed Wacker, of course, the edger, and the limb chainsaw attachments.

@HomeGaragechannel

4 жыл бұрын

You're welcome and thanks for the comment I appreciate it

@JamesDayley

4 жыл бұрын

@@HomeGaragechannel btw, did you get the push-button starter to work?

@HomeGaragechannel

4 жыл бұрын

@@JamesDayley yes I did but I had to use a temporary battery

Thanks,I now understand how a caburator works,the video is very helpful much appreciated

@HomeGaragechannel

3 жыл бұрын

no problem Emerson Campbell

Thanks for a great video with such clear narration and videography!

@HomeGaragechannel

2 жыл бұрын

Glad you enjoyed it!

I just bought a broken Ryobi trimmer. It's a 767r, 16", 31cc unleaded 32:1model. I intend on fixing it and selling it. Your video helped me get back into the swing of things. I'm interested in knowing how to adjust a carburetor to get it to run on steroids. Most people think that an engine that spins fast will get the job done , that's where I'll make my money. I'll subscribe to your videos. Blackjack '98 enterprises.

@HomeGaragechannel

5 жыл бұрын

Thank you for the comment I appreciate it.

Nice video!! Good job!! Thanks for posting!!

@HomeGaragechannel

5 жыл бұрын

Thank you for the comment I appreciate it

I have had a Ryobi trimmer for 20+ years . I bought it when I bought my home in 1998 expecting it to only last a few years . With proper care and maintenance , this still has 95 psi and now powers a pole saw , hedge trimmer as well as the ( original ) dual line trimmer head . BRAVO Ryobi !

@HomeGaragechannel

5 жыл бұрын

Wow.. you've given it excellent care. Thanks for the comment I appreciate it

@tonyabruzzo4147

4 жыл бұрын

Same 2 cycle model?

I have one, but it has been stored for 4 years now because it stopped running after only using it 4 times. I will be bringing it back out this year to see if I can get it to start. Not too sure if the carb is finicky or if I need to change the plug (the plug is 4 years old, but stopped running when it was 4 months old. I really should have returned it but I wanted it for attachments. Thank you for the details you provided in this video.

@HomeGaragechannel

4 жыл бұрын

No problem and thanks for the comment I appreciate it

I bought the Ryobi PLT254y a few years ago, it stopped working after approx 10 mins and as never worked since, I wasted my money. Enjoyed watching your video, doubt if mine would ever run again without spending more money on it.

@HomeGaragechannel

2 жыл бұрын

Sorry to hear that

Brilliant video learnt a lot I have the ryobi RBC30SET brush cutter electric start nice to just have to push a button to start but only problem can't find parts for it. Starts up then dies and when pressing the trigger its spins then stops spinning continuously never spins for long hopefully adjusting the carb will work

@HomeGaragechannel

4 жыл бұрын

yes try adjusting the carb if it doesn't work replace the carb.

Great video and I learned a lot but I keep having problems starting it up after I don't use it for a while. I've done full carb replacements and it works great for a season then the same start problems return after winter storage. I'm going to give mine to the neighbor's gardener and replace it with the 40-Volt electric Ryobi trimmer.

@HomeGaragechannel

4 жыл бұрын

Good choice. Most of the problems after winter storage is fuel related.

@darlalasalle3457

4 жыл бұрын

After use, pour the fuel out of tank into container. Start motor & let run until it uses up the fuel in the carb. This should help your issue.

@HomeGaragechannel

4 жыл бұрын

@@darlalasalle3457 thank you you are absolutely correct.

Excellent video, thank you sir

@HomeGaragechannel

4 жыл бұрын

Thank you for the comment I appreciate it

Thank you for the video . I have a CS26 Ryobi. Mine is having troubles starting as been sitting for few years as well without using. Noticed some fuel dripping from the carburator. So may have to check some of the things you did here.

@HomeGaragechannel

3 жыл бұрын

Yes I would definitely check the metering diaphragm for a problem

@ExplorewithMJ

3 жыл бұрын

@@HomeGaragechannel I checked the carburator and took apart and back together. Was able to get it started but run into same problem where it won't stay running and is running rough. So had to order the tools in order to do it as no one had in stock close by.

@HomeGaragechannel

3 жыл бұрын

@@ExplorewithMJ okay hopefully you can make the adjustments, you didn't want to replace the carb?

@ExplorewithMJ

3 жыл бұрын

@@HomeGaragechannel it looks in great shape. For a replacement, mine is in the $35 range.

I got two ryobis off the side of the road and both work like a champ.

@HomeGaragechannel

5 жыл бұрын

Excellent. Thanks for the comment I appreciate it

Thanks for the great video, newbie here, learning.

@HomeGaragechannel

Жыл бұрын

no problem and welcome aboard.

Since this is an old video, I noticed some steps you missed after watching a lot of your newer videos. I don’t really want to spoil anything other than to say that your technique has definitely improved over the course of time. Watch more of his videos folks!

@HomeGaragechannel

Жыл бұрын

yes there's an element of time, that I didn't have, in the earlier videos. I really appreciate the compliment.

I picked a 4 stroke 30cc trimmer up next to a trash dumpster a month ago. Apparantly the original owner couldnt put up with the temperment. I stripped it all down and am in the process of making a gas powered longboard. I'll reuse the cyntrifical clutch, pull starter but will rig a direct drive belt to the skateboard wheel and make a supertrap style layered exhaust pipe. I'll use a thermos for the fuel tank. A hand heald cable throttle. With correct gearing i should do about 25mph!

@HomeGaragechannel

4 жыл бұрын

Nice project. I wish you the best of luck with it. Thanks for the comment I appreciate it

After my second power head in as many years, I bought an echo. I kept both power heads. After watching this I feel brave enough to attempt a cannibalization effort, maybe salvage one of them. Honestly I've used the heck out of them. Pole Saw, Edger, Weed Wacker and Bush Trimmer/Hedge Trimmer. I've worn each of them out in literally one year. They are probably fine, just needing regular maintenance that I've neglected. (but in just one year?)

@HomeGaragechannel

4 жыл бұрын

Its been done before. It just depends on how much you use them. Thanks for the comment I appreciate it

@tonyabruzzo4147

4 жыл бұрын

@@HomeGaragechannel It worked, however carborator & seals were different models except the seat seal on engine block. I cannibalized that as I had a leak. Got everything adjusted. Now add a Tiller tool to the list of tools I'm operating with this. 👍

@HomeGaragechannel

4 жыл бұрын

@@tonyabruzzo4147 nice work. Thanks for the comment I appreciate it

Thank you very much for this excellent video

@HomeGaragechannel

3 жыл бұрын

No problem and thanks for the comment I appreciate it

I have a Ryobi trimmer and it is hard to start but it is getting better as I tinker with it. I like the removable heads to switch from trimmer to edger to heavy trimmer. I got saw blades on one head to prune trees and heavy brush. My motor is smaller and not strong, but is getting the job done. That pac-man screwdriver is a nuisance.

@HomeGaragechannel

11 ай бұрын

nice work, I'm sure you'll get it where you want it.

I put a new carb on my ss30 and worked after install, but it dies after a minute. I'd start it again and it would do the same. Then a couple of weeks later, it would start with one pull with choke on. When I pull the trigger(choke off) it bogs down and die. Gonna go try and adjust it the way you did. Luckily, the carb kit I bought came with the screwdriver adjuster. Thanks!

@HomeGaragechannel

5 жыл бұрын

Thanks for the comment I appreciate it. Good luck.

@squidusn71

5 жыл бұрын

@@HomeGaragechannel Just finished weed whacking! Your vedio helped, thanks!!! The mistake I did however, was adjusting it while it was still cold. Must run the trimmer and let it warm up to temp then adjust. Thanks again for preventing me from buying an Ego cordless which I dont think will outlast my ryobi or match the power. I bought it as a refurbished back in 2008. It runs stronger now with the new carb.

@HomeGaragechannel

5 жыл бұрын

@@squidusn71 I'm glad it worked out for you. Thanks for the comment.

Have used one and love it

@HomeGaragechannel

4 жыл бұрын

Nice. You're one of the few.

i love watching youre videos

@HomeGaragechannel

2 жыл бұрын

thank you Michael Bond.

Thanks so much! Used this guide to fix mine that I acquired free because the previous owner couldn't get it to work. Although something seemed odd when they listed it as a diesel strimmer... 🙄

@HomeGaragechannel

4 жыл бұрын

Nice work. Thank you for the comment I appreciate it

i have had my Ryobi for last ten years and i have only had to replace the fuel lines one time only i am working to two more now and have ready got one going so by time theses going i will have for they are great for home uses instead buying big name products i would not change

@HomeGaragechannel

2 ай бұрын

thanks for sharing

Had the problem of the trimmer bogging and was hoping I;d find a solution. But found that the carb had vibrated loose. Once tightened bingo no more bogging and the trimmer rev'd up as it should.

@HomeGaragechannel

4 жыл бұрын

That was the problem I had on my my very first piece of equipment. Thanks for the comment I appreciate it

I have a early model ryobi weed viper 31cc mid to late 90s model here in Australia I have just put my first car by kit through it and it runs like a dream I had problems with the spool and gear box could not find a replacement so I changed the whole shaft and put a split shaft on and now I can put different attachments on but the motor plenty of comp and don't say no

@HomeGaragechannel

Жыл бұрын

very nice work.

Wow , this ad really helped me, i like it.

@HomeGaragechannel

6 ай бұрын

buy buy buy

have an older Ryobi replaced primer bulb and lines tested plug with ohm meter tested good I know its getting fuel (plug is wet after pulling rope multiple times will test for spark and perhaps throw it out

@HomeGaragechannel

5 жыл бұрын

At least you tried before throwing it out. Thank you for the comment I appreciate it

I have the SS26 and bought a new carb off Amazon...it fired up but I didnt notice the line leak....I struggled trying to get the new fuel lines back in the tank...the angle trick helped tremendously...my new issue is now my primer bulb squeaks when you press it...I installed a new one...but it does the same thing any advice would be appreciated! Thank you for the awesome video.

@HomeGaragechannel

4 жыл бұрын

Thanks. Does the primer fill up with fuel or does it just squeak and doesn't fill? If it doesn't fill then there is an air leak on the carb. Take the carb off the engine and reinstall the bulb.

I appreciate your video and thanks for your thoughts. I don't think I would push for a ryobi but I thought I could get mine to work. It originally would crank but not run for more than 10 secs. I noticed my fuel lines were bad and need replacing so I just did the whole kit exchange-new fuel lines, filter, carburetor and now it won't start at all. I have a 2 cycle gas trimmer/edger. I was told with new carburetor shouldn't need adjusting, not sure if true or not but either way it wont start with new parts. resistance on chord but will not begin to crank. just curious what next steps you would consider?

@HomeGaragechannel

2 жыл бұрын

after repeated failed attempts to start a trimmer , it will typically flood. let the engine dry out and then try to start it again. No, sometimes the carb needs to be adjusted , because the carb is new, but the engine is not.

i have the same exact trimmer. I bought it new and the electric start worked well in the beginning but then something happened to the battery. I think it was overcharged. I am currently rebuilding mine. Parts are cheap. I suggest a new fuel cap as it has to provide a little air for proper fuel flow. As far as the battery it wont charge so I have to get to the bottom of the problem... charger or battery

@HomeGaragechannel

4 жыл бұрын

Thank you for the comment I appreciate it. Let me know if you get it fixed.

@designusai

4 жыл бұрын

If it is a lithium battery you can't run it until dead or it will quit. It's a simple fix & there are videos on KZread detailing the procedure

Thank you I’m learned a lot

@HomeGaragechannel

4 жыл бұрын

Thank you ed Aleman for the comment I appreciate it

i fixed one that was thrown out with the trash the very same way you fixed this one. my question is when attempting to start mine the lever always goes from full choke to run i cant set it on half choke is there something i can adjust

@HomeGaragechannel

3 жыл бұрын

this one is semi choke so while in choke, and you press the throttle, the choke will move to the run position. it's made that way on this model

These pulling cordes are headaches get your blood pression and heart beat rising up .I did all that changed the spark cleanup the carburateur he start back but next late spring it gonna be the same I m going electric .

@HomeGaragechannel

5 жыл бұрын

Good choice thank you for the comment

I have serviced a bunch of these. I cant really tell by the microphone on your camera but it sounds a little muffled.no pun intended. I would remove the muffler and run it to see if the power and RPMs pick up. Also check compression again while the muffler is off. You will have it humming I'm sure. You always do! 👍

@HomeGaragechannel

5 жыл бұрын

Thank you Dave for the comment. Yes more than likely the muffler has an issue. I check it out.

@js_1995x

4 жыл бұрын

If you run without muffler it will shoots sparks and you can burn up the rings

Ryobi has discontinued making carb rebuild kits on early model 4 stroke blowers. I guess I will have to put mine out at the curb too. Good luck Jon G

@HomeGaragechannel

3 жыл бұрын

Thanks for the comment

@tave9011

3 жыл бұрын

Amazon has the carbs $15

I have a new Ryobi trimmer that cost 99 bucks and it's been great.....smaller and lightweight it's easier to handle for hours on end and is quiet too.has plenty of power

@HomeGaragechannel

4 жыл бұрын

I don't have a problem with the newer ryobis they're pretty decent

Hi thank u for us I like the way u chow where do u buy diagram and the one fix the throttle thank u agian

@HomeGaragechannel

4 жыл бұрын

You can buy the diaphragm from Amazon. Just search for echo carburetor diaphragm

Thanks for the video..very helpful. Im using rlt26sdnb model. Ive replaced fuel lines and spark plug but will only run 2min..so i think i need pacman tool to stop it bogging out. Thankyou

@HomeGaragechannel

Жыл бұрын

thank you Christopher Young, good luck with it.

@set3777

Жыл бұрын

I have a PLT3043S that would stall. Replacing with a brand new caburetter didn't help. In despair I had bought a Ryobi 1200W AC (RLT1238) line trimmer to use my expand-it attachments. BUT the high frequency noise of the 1200W electric Line Trimmer made my neigbour yell at me to stop using it. I finally cleaned the "spark arrester" screen of the muffler of the PLT3043S and now the 30cc Petrol Line Trimmer is running well again.

Good explanation.thanks

@HomeGaragechannel

Жыл бұрын

You are welcome

currently looking at a Ryobi 25 not starting recently replaced many of the usual suspects fuel lines, fuel filter, air filter and I have spark. A good strong spark. checked carb jets/injectors all seem fine. Getting a great work out from pulling the starter to no avail. Now considering a replacement and am considering cordless over petrol any thoughts?

@HomeGaragechannel

2 жыл бұрын

go ahead and get the cordless.

Good luck finding the battery for them. The good news is its a simple positive negative system. I have the leaf blower that looks like new. I intend to use a Lithium battery on it using a simple conversion wiring with a fuse to prevent burnout. As its a 12 volt system and 1500 MAH any RC plane battery should do it. I had no idea they sold a weed eater too. My son in law gave me the blower, it's like brand new.

@HomeGaragechannel

4 жыл бұрын

I did find a battery and charger but the combo was too expensive for me. Thanks for the comment I appreciate it

@scottfirman

4 жыл бұрын

@@HomeGaragechannel I think I saw the link, it was $50. That was just too much for something that old. Sadly that battery is not a common battery at all. I have been able to get most older Ryobi's running again, regardless of age. Sadly, the battery start system was a gimmic and didn't last long. Lithium took over shortly as did 4 stroke engines. I find the 4 strokes too heavy and uncomfortable to use. They do make one hell of an RC plane engine however( the non starter kind)

@HomeGaragechannel

4 жыл бұрын

@@scottfirman I'd rather put the $50 into a better commercial trimmer is all. The pull rope still works fine so it would be for a feature that's a Luxury

@scottfirman

4 жыл бұрын

@@HomeGaragechannel OH I agree. I am going to use a lithium 12volt battery from an RC plane to power it up. That should work just fine. As long as it runs. I have health issues as far as pulling rope starters thats all.

@HomeGaragechannel

4 жыл бұрын

@@scottfirman I understand. Good luck with the project.

Great video, thanks

@HomeGaragechannel

3 жыл бұрын

Thank you Graham Organ

Great video. 👍👍👍👍👍

@HomeGaragechannel

5 жыл бұрын

Thank you RayFpv for the comment I appreciate it.

someone threw a similar Ryobi edge trimmer unit away. I put some fuel and oil in it and I got it running after a few starts, but it only would run for a few seconds, and after a few restarts I never got it running again. Will put it away and let the petrol evaporate and try it again another day

@HomeGaragechannel

2 жыл бұрын

that's what I would suggest as well, thank you wongway40

Great job! Thanks!

@HomeGaragechannel

2 жыл бұрын

Thank you Michael Hamann

Hi, My issue with a ryobi is the similar to your problem at present. It did start but the speeds on full power varied, I have changed the carb but the fuel lines are not fitting very tightly on the ports , I think someone has altered the size of the holes in the tank for some reason. I know there are different sizes of fuel line but don’t know how to make a larger cable fit on a smaller port., any ideas

@HomeGaragechannel

2 жыл бұрын

sure buy a multipack of lines, that have 4 different sizes. If the lines have been opened, the larger line in the pack, should take of the size difference.

Excelente video 👍

@HomeGaragechannel

4 жыл бұрын

Thank you Pedro Henriquez for the comment I appreciate it.

Let me ask you this,, where do you find the primer bulbs for this type of trimmer,, I am having a hard time finding them,, thanks John W

@HomeGaragechannel

3 жыл бұрын

look in the description of this video as I have a link to them.

They run decent when they are running... Adding a air filter may help it run better. Adds a little drag

@HomeGaragechannel

4 жыл бұрын

Thank you Rusty nail for the comment I appreciate it

I have a Ryobi strimmer....different model. haven't used it for over then years, but looks new......so far I've not been able to start it. I've tried replacing the spark plug. i'll try the tip for checking for a spark. No idea what to do if it doesn't!

@HomeGaragechannel

3 жыл бұрын

unless for a trimmer is the worst on the Fuel system. Usually Fuel lines degrade and brake and the Carb will also fail internally. I would suggest replacing the fuel lines and the carb.

I just replaced all the gaskets and metering diaphragm on a old craftsman 32 cc. Made in 2005. New filter. New lines hooked up right. Waiting on adjustment tool kit. But something happened during pulling....it was running for 5minutes. Now its feel is like no compression....will check with compression tester

@HomeGaragechannel

2 жыл бұрын

let me know what you find out.

Thank you very much.

@HomeGaragechannel

4 жыл бұрын

no problem and thanks for the comment I appreciate it.

By the way, what are the fuel line dimensions and where did you buy it? Thank you.

@HomeGaragechannel

4 жыл бұрын

The line is 3/16" and can be found at lowes,home depot, or ace hardware

Where did you find the carburetor parts? Thanks for the video. It was a big help.

@HomeGaragechannel

2 жыл бұрын

I found them on amazon.

Well, interesting vid, I have 3 plus one spares 26cc and 3 30cc, i just buy any going on the market for 20-30 quid. then all the parts you need for the good runners are there. carb, piston, spark, starter coil, starter pulley the lot! takes about an hour or so if you know where you are going with it. I love messing about with mine, although I don't like to hear the chicken chaser setup (extreme high revs) if you see what happens inside then what come from inside to the outside, play it safe and get them running sweet. I usually take 2 of these bad boys on jobs with me. 1 to strim and the other to cut bushes or do pruning. if 1 fails I have the other as a backup. I did have a case just the other day where 1 died (vexed me) and then the second one decided to snap the starter cord..... Left me in the SH**, but managed to tell the client and return the next day for finishes. YUP I lost monies a little, but those machine cost me about 60 to buy, and have made a hell of a lot more. and I love fixing them ( it vexes the wife, so I am happy) Peace out dudes.

@HomeGaragechannel

5 жыл бұрын

Excellent you seem to have a good system.

Thanks! That was really educational. I need to do the same on my 790r that hasn't been used in years. Let's hope it works. I have a massive bougainvillea to whack!

@HomeGaragechannel

4 жыл бұрын

Thank you Raneil Alonzo for the comment I appreciate it

Awesome vid and commentary. My Ryobi starts and runs good but will not idle... suggestions? Thanks

@HomeGaragechannel

4 жыл бұрын

sure, try turning out the L screw on the carb about a quarter turn counter clockwise. you're adding some fuel at idle so it will slow down the engine. if it does slow down turn the idle screw clockwise till you like the engine speed.

I would recommend Ryobi - but only if you know how to do repairs. They are abundant on curbs and recycling centres as no shop will fix them - not financially viable. By the way, I had the same problem with a Ryobi with the same carb and engine (not electric start though) - take the high speed screw out completely and blast a shot of aerostart, degreaser or the like with a small pipe nozzle. In my case, that cleared the blocked hi speed nozzle. Goes well now

@HomeGaragechannel

5 жыл бұрын

Thank you Tyler Campbell for the comment. That's a great tip I'm going to have to try it out.

@botiroti1

4 жыл бұрын

Tyler C how do you know how far to reinsert the screw?

I have the 30cc curved ryobi RLT30CETG Australian model which looks to be exactly the same except is fluoro yellow. Will those parts be compatible with mine ? I would like to try and service carry and replace fuel lines. My pull rope has snapped and I charged the battery after 3 plus years of non electric start and behold the damn thing fired up and ran. So I don't have to throw it out as it still goes. You make excellent videos thank you in advance.

@HomeGaragechannel

3 жыл бұрын

thank you the naked ape, I believe so, go to ereplacmentparts dot com and enter the model number and see what you get.

@thenakedape55555

3 жыл бұрын

@@HomeGaragechannel thanks for your quick reply, you really make excellent and helpfull content 😊

@HomeGaragechannel

3 жыл бұрын

@@thenakedape55555 thank you I appreciate it

The old ryobi trimmers work good with the 31 cc engines are good

@HomeGaragechannel

5 жыл бұрын

Thank you Charles Pittenger for the comment. Yes the 31 cc engine is powerful.

@andybecker2693

4 жыл бұрын

Good engine but a real PIA to work on.

Have the same trimmer and it just stopped running last weekend. (Have had it for 5 yrs with no issues) bought the fuel line kit & changed the filter (it needed changing) replaced all fuel lines (all were hard & cracked) replaced bulb ( it was split). Still wouldn't fire. Took carb apart, cleaned it still won't fire. Tried start, still won't fire. Checked spark plenty but still replaced plug. Bought new carb, installed it but still won't fire.... checked cam, they're metal ( not the plastic one I've seen on KZread) all were good. Only thing I didn't do was check compression but at this point I'm thinking it's time to replace the trimmer. Any other ideas?

@HomeGaragechannel

4 жыл бұрын

You given it all you can. There's no shame in putting it on thr curb for the next person to fiddle with and get a new trimmer.

Can you tell me if a 8”circle blade brush cutter fit the Ryobi trimmer? i have the attachment but i want to replace the triangle one for the circle ⭕️ one

@HomeGaragechannel

3 жыл бұрын

it should fit as long as the hole in the center of the blades are the same size.

@davidgaleano9207

3 жыл бұрын

@@HomeGaragechannel Thanks so much for replying!

@HomeGaragechannel

3 жыл бұрын

@@davidgaleano9207 no problem

I have a 780R Ryobi and it is so hard to start the engine pull string fights me and pulls back , WHY???

@HomeGaragechannel

4 жыл бұрын

Does the engine eventually start? If not then there might be fuel leaking into the engine and its trying to hydrolock

At the end of the video its suggested that another video would be made to address the wide open trottle problem. I cannot find that video so I was wondering if you got it running properly with wide open trottle? and what you did to solve that?

@HomeGaragechannel

4 жыл бұрын

I didn't get a chance to make a video on it as I sold it soon after this video was made. In the end it just needed more carb adjustment to get it to run at full speed.

@mp-ck8gm

4 жыл бұрын

@@HomeGaragechannel thanks for the update I'll give that a try.

Great video. Very detailed. I have a question. My choke/run/stop lever broke. Can it be replaced? I have a Ryobi BC30 trimmer with an edger and tiller attachments

@HomeGaragechannel

3 жыл бұрын

thank you and yes you can, heres the one you need. amzn.to/3qWb4iZ

@robertbove5769

3 жыл бұрын

@@HomeGaragechannel thanks but the original lever looks like it was one complete yellow plastic piece in the shape of an L. The long cylinder piece that attaches to the flap is still in the carburetor. The short lever piece is what broke off of the shaft...I think. Or does the part you showed me just pop on the end of the yellow piece that is still in the carburetor?

@HomeGaragechannel

3 жыл бұрын

@@robertbove5769 yes you just pry up on the old broken yellow piece and push the new one on. It only goes on one way.

@robertbove5769

3 жыл бұрын

@@HomeGaragechannel thanks. I am grateful that you responded and so quickly. You are the best. Thanks again.

@HomeGaragechannel

3 жыл бұрын

@@robertbove5769 no problem

My ryobi strimmer will not start...I have changed tyhe spark plug and it is sparking.I have cleaned the carb but still no start.I replaced the carb but still no start.The compression is good and the fuel line is ok as is the air filter and fuel filter is fine.I am stumped ...Any suggestions?

@HomeGaragechannel

4 жыл бұрын

Did your new carb come with a new gasket that goes between the engine and carb? Also It may be flooded. Try moving the choke to run, squeezing the trigger and then pulling about 10 times. Let me know what happens.

@castlecob

4 жыл бұрын

@@HomeGaragechannel will do

I have the exact same trimmer and i got it running few days and then all of a sudden it started smoking like crazy. these are very difficult to start manually. but you can use any 12v with jumpers to start it. no need to buy that original expensive battery that lasts only few hours. Although you should have cleaned that small carb screen inside in the video it looked like it had dirt in it.

@HomeGaragechannel

5 жыл бұрын

Excellent, I thought I was the only person who had one of these. Thanks for commenting.

@WV591

5 жыл бұрын

@@HomeGaragechannel in my case..back to the drawing board. i've never seen trimmer smoke like that.the starter is ok. that only leaves the rings.must've been that cheep mixing oil i used with expensive ethanol free gas.

@HomeGaragechannel

5 жыл бұрын

Try using premix in a can and if it smokes still then check compression. If it still smokes then its the rings. Is the carb working properly?

@WV591

5 жыл бұрын

@@HomeGaragechannel well too late for trying premix. i already took most of it apart. carb was right on. I have a feeling using that STP 2 cycle universal oil mix was not good for this fellow even though it ran just fine for couple of days. when i get a chance I will gut it out and take a look at the rings and see how much damage was done.....BTW, if you flip this and engine to your right and you looking down at battery holder, the connector close to you is +.

@HomeGaragechannel

5 жыл бұрын

Cool thanks

I pick one up someone left out with the trash it only needed the vent on the gas cap cleaned it wasn't getting enough air.

@HomeGaragechannel

3 жыл бұрын

nice work

I have the SS26, Your video is great! Mine still wont start.. =-( I have a new Carb with all the goodies. New Spark plug, filter, gaskets... I changed them all, still nothing. It used to run, just not good. Now nothing. No idea what to do next.

@HomeGaragechannel

5 жыл бұрын

Thanks for the comment. Did you check for spark or engine compression?

@Thedosh5824

5 жыл бұрын

@@HomeGaragechannel That's next..

The most common issues with weed trimmers that sit up,"or sit in the elements that are really not mentioned,'As we may know that is more mentioned',low compression,and the carburator gumming up..even replacing the carburator and trying to adjust it sometimes will still get some bogging at open throttle,stalling or surging,they are other factors that contribute to that is the Coil"even if it sparks! The ignition can still be weak,when the spark plug is inside the engine under compression is when the spark becomes weak if the coil is bad..get specs,and check the ohms,if the resistants is too high above specs the engine will be hard to start,and flood very easy,also crank shaft seals dry rot,and want hold back pressure to allow the spark plug to ignite the fuel 90% it will not start if thats the case..also carbon build up in exhaust or muffler aswell.

@HomeGaragechannel

4 жыл бұрын

Thanks for the information I appreciate it

@tc7694

4 жыл бұрын

NP... just be aware that the coils are vunerable in weather they are not good quality in the basic weed trimmer products compare to commercial type stihl,toro,or honda that are more expensive though cause they last much longer,and easier to repair by usually replacing the carb,and kill switch..if you have any questions feel free to ask!

Thanks I can now go fix mine

@HomeGaragechannel

2 жыл бұрын

no problem and thank you Craig Stevenson.

After 6 months, primer bulb does not prime even with new bulb, had to get new carbs as no amount of carb cleaner + compressed air fix the problem. Now I have dozen carbs after few years of use. I'm going to get corded electric one (120V, 10A) with inverter + deep cycle battery (or use my car battery). No more pulling cord to get it started and no fuel to mess with.

@HomeGaragechannel

4 жыл бұрын

That will work too. Thanks for the comment I appreciate it

try looking at the spark arrestor screen on that unit mate cheers from Australia

@HomeGaragechannel

4 жыл бұрын

Thank you for the comment I appreciate it

@Patrick4959

4 жыл бұрын

@@HomeGaragechannel my pleasure if you take a propane torch to it and burn off any carbon deposit residue and let it cool and then re-install it should improve the RPM performance and even on Idle

I have a Ryobi just like this but the clutch bell is stripped and head won’t spin. I can’t figure out how to get it off the housing cover

@HomeGaragechannel

5 жыл бұрын

I have this video on my channel it this helps. Thanks for the comment. kzread.info/dash/bejne/d5mXpLZso5qZf5c.html

@stevenhammett219

5 жыл бұрын

Home Garage the actual drum is what I’m having trouble getting out. It is rounded out and won’t turn the drive shaft

@HomeGaragechannel

5 жыл бұрын

So the driveshaft isn't damaged but the squared snout on the drum is rounded ou on the inside? I'd never seen that. Its soft steel have you thought about just try to reshape the snout with some large pliers?

@stevenhammett219

5 жыл бұрын

Home Garage I can give that a try. But yes that’s exactly what is going on. I will try to do that but I still might need to get the drum out

I followed directions but still won’t start. I get one puff of white smoke. Any suggestions.

@HomeGaragechannel

Жыл бұрын

sure, if it was me, I would do a compression test, and if that was good, I would replace the carb.

So why did it all of a sudden start when you used starting fluid?

@HomeGaragechannel

3 жыл бұрын

good question, there might have been a small blockage in the carb that didn't let it start when I was pulling on the rope, using starting fluid, got the engine to start, and it might have then dislodged the blockage out of the carb, and that let me start it normally.

For these, Wht battery would it take? 18v?

@HomeGaragechannel

Жыл бұрын

no it's 12v

I bought a new carb and replaced fuel filter and tubes. Also new sparkplug. Still won't start.

@HomeGaragechannel

3 жыл бұрын

Try starting with no choke and full throttle. If it doesn't start then put some fuel into the carbs throat and try starting it.. if it still won't start Check the compression

While you did get it running in the end, not sure if i agree with your trouble shooting and repair process. Seeing as you had the tool i would have done a compression test first, easier to do than taking off the carb and would tell you if its even worth putting any parts or time into it, seeing as you ended up checking it anyway. Nice video anyway

@HomeGaragechannel

4 жыл бұрын

Thanks. Most people don't have a compression tester so I don't do it first.

hi what causes my lawn mower ketch on fire whin spray gas in carb

@HomeGaragechannel

7 ай бұрын

without know what make and model your mowers, I can only be guessing but, I would have to guess the valve lash is a bit too tight.

@tntreviews3602

7 ай бұрын

I CHECK THE VILES BUT IT HAD NO CONPRESHON THANKS MERY CHRISTMAS@@HomeGaragechannel

Where would you buy a topping kit for a small engine

@HomeGaragechannel

2 жыл бұрын

can you elaborate what you mean by a "topping kit"

@christianparkour8880

2 жыл бұрын

@@HomeGaragechannel you know how you would say that if something lost compression you would have to get a topping kit like a rebuild kit for an engine

@HomeGaragechannel

2 жыл бұрын

oh I see, the cost for the kit could be anywhere from $50 to $100, most people wouldn't bother, I you want want to look it up, have the model and serial number ready and go to Ereplacmentparts dot com

@christianparkour8880

2 жыл бұрын

@@HomeGaragechannel alright thanks

I have a es30 trimmer i need a few parts fo it where do i get them from

@HomeGaragechannel

4 жыл бұрын

I order them from Amazon. If you can't find them there look at Ereplacementparts

@tc7694

4 жыл бұрын

What part you need?

@orvileoquinn9869

4 жыл бұрын

@@tc7694 carb. And starting cord and pulley that goes behind the clutch

Hi. Can u send the link of the later video u mentioned on 14:08 min. Thanks 4 the very helpul video !

@HomeGaragechannel

5 жыл бұрын

Thanks for the comment. I sold the the trimmer soon after the video series was finished so I no longer have it.

@geolous4966

5 жыл бұрын

@@HomeGaragechannel So what do u suggest to me? At idle state it works until I speed it up. It's bogging down and goes off. The engineer turned the two bolts a couple off times, I used it for 5 minutes each time, and it went off again. Shall I add more fuel at idle, or adjust the throttle by turning the H anticlockwise (to the left)? Thanks for the valued information u give to us!

@HomeGaragechannel

5 жыл бұрын

@@geolous4966 yes turn the H screw out a little bit more and again if you have to. However if you keep turning it and it still does it again you might need to open the carburetor and take another look at the metering diaphragm. It might be flexible not it might be just still enough that it runs out of gas after a few minutes

@geolous4966

5 жыл бұрын

@@HomeGaragechannel thanks a lot once more. I'll try it!

@HomeGaragechannel

5 жыл бұрын

No problem

Before replacing the fuel filter, make sure it is clean. Blow out with compressor our blow through it

@HomeGaragechannel

11 ай бұрын

good idea.