Fix Power Window motor Ford Club Wagon VAN
Автокөліктер мен көлік құралдары
BUY Complete motor HERE -- amzn.to/2sMhfeo
BUY gear replacement HERE -- amzn.to/2sM1Xq1
This video show you roughly what it would take to put new gears in the window motors of a Ford product anything from really the 1980s up until the late 90s so from 1982 up to 1997 this would work in the E-150 and also the Club Wagon Vans also of course the F-series pickup which would be the F150 F250 F350. And quite a few others now I do show how to reinstall the regulator and motor back into this 1988 Club Wagon Econoline van because that's specifically what I was working on but this is really to show you how you can replace the gears and not replace a good working motor to save yourself some money. This will allow your windows to start going back up and down again with smoothness. So if you're window has stopped going up and down on your Ford product but you can still hear the motor running then most likely you need this fix
Пікірлер: 37
in place of the push washers, I've made my own out of plastic from a milk jug, just drill a hole one size smaller than the bolt and thread it on
@Foxboss9
7 жыл бұрын
Your Tip gets the Loved comment!! and Pinned to the top.. Great job!!
@hotrodrebel855
2 жыл бұрын
Great idea!!
Nice job! I have a 1995 Ford E-250 Van that needs this exact repair and I found this video extremely helpful. Thanks for posting!
Just so you know there's usually dimples in the door if not you can figure out where the bolts are in the motor drill half inch holes remove the motor without taking out the regulator way easier that way I've done hundreds of them
this guy should charge money for this video. thanks SO much for the video.
8-3-21 and this is still a very informative video. Thanks for the help. mine went smooth after watching this!
I did this on one side. It kinda sucked. When I did the second one I left the regulator in the van. Don't drill thr rivets out. Drill 3 1/2" holes to remove the bolts that hold the motor. Mine did not have dimples where the holes go, but I used step drills and was able to 'wallow' the holes to match the bolts. It came out pretty clean and much time saved.
Great job! That Ford van sure is a very clean. I have done a lot of window regulators and I have to explain those cuts on my forearm and wrists lol! That's really cool you can get all the replacement parts and still use the original window motor.
@Foxboss9
7 жыл бұрын
😊
Hey-Great how to. Just did mine with a low cost motor with your help. Had I seen your video before buying the motor, I'd have rebuilt mine. The aftermarket one is less than half the size of the OEM. I'll still rebuild the original for a spare. Thanks
@Foxboss9
5 жыл бұрын
👍😁
Just takes a little patience. And some sticking out of the tongue! Thanks for the tips. Big help!
Thank you very much for your help, it was helpful and got the job done.
@Foxboss9
6 жыл бұрын
James Knox 👍😁
@jamesknox955
6 жыл бұрын
Thank you very much for your help, it was helpful and got the job done
Very well done thank you
Nice video, I would like to see the whole process , even when you drill out the rivets.. Also an idea of where the track is on the regulator, thanks
Yeah Test it before installing the door panels etc. Nice job.
@Foxboss9
7 жыл бұрын
Darrell Wampler 👍😁
In the tutorial you say you used 1 3/4" bolts Did you mean 3/4"? I'm thinking of getting 1/2" Nice video thanks for the help!
@Foxboss9
4 жыл бұрын
No, those bolts in the video were 1-3/4 long before I cut them off..
Thank you
motor clicks but does not engage what do you think the problem is?
I kind of wonder why they would use plastic gears since they are probably less durable than brass, possibly it saves the manufacturer money.
@Foxboss9
6 жыл бұрын
Robert Sitch it's supposed to be a sacrificial piece to save the more expensive motor from damage... But mainly cost.. remember They were using nylon gears on the engines timing gears too!
@RobertoSantiagoRodriguez
6 жыл бұрын
Safety, that is why. If someone gets an arm or their head stuck in the window path, the plastic will be crushed and the motor will just free wheel instead of harming the person, pet or what have you. Also will keep motor from overheating and catching fire. 😁
Thks Man!
@Foxboss9
5 жыл бұрын
👍😁
I don't hear anything when I hit the switch, my window is stuck down and with the panel off I can't force it up to get it out of the way!
Nice👍
@Foxboss9
7 жыл бұрын
👍😁
Would rivets work here? Interesting job 😀
@Foxboss9
7 жыл бұрын
Yes But BIG Ones
@Foxboss9
7 жыл бұрын
The drilled out hole size is about 5/16"
@rstormo68
7 жыл бұрын
Nice to see parts that are serviceable !
Thanks