Fix heat dissipation issue on Aiyima A07 TPA3255 amplifier
#aiyima #tpa3255 #diy #classdamplifier
Жүктеу.....
Пікірлер: 41
@tallpaull9367 Жыл бұрын
I drilled a strip of holes down each side and a patch of holes on top right over the heat sink. I use a 48V power supply dialled down to 44V. works great
@therottenbug3675 Жыл бұрын
the mods looks great, hope that they also lift up the soundperformance-notch a bit
@LabArlyn Жыл бұрын
Is Nichicon Fine Gold cap good for signal input ? 💌
@gherbent Жыл бұрын
Why? Just use an aluminium block to connect it to the enclosure cover, this will result in direct heat contact with the cover (enclosure body).
@tallpaull9367 Жыл бұрын
Cool, haven’t seen anyone mod quite that much on a A07 yet. You changed a lot of parts. Did you find the upgrades worth it? Significant improvement in sound quality….? What was the total cost in parts for all of that?
@AnasSuhaimi Жыл бұрын
The inductors, looks like you replaced them. What iductor are you using? Brand, model and spec please
@trungqn1890
Жыл бұрын
First, I replaced with coilcraft ver2923 oem, 10uh. After i replaced with 6,8uh. You can see it in my latest videos
@awaken9297 Жыл бұрын
What caps you use for replacing 2x 1200uf on supply?
@trungqn1890
Жыл бұрын
i replaced with nichicon FW 1000uf 63v
@editorjuno Жыл бұрын
I own four A07s and have found that the "heat dissipation issue," while certainly measurable, presents no problem whatsoever in actual use playing music. I have two in my main system driving my ambience/surround speakers and never even had a benign output chip shutdown. I'm sure your mod will make yours run cooler, of course -- but, at least in my experience, it's a solution in search of a problem.
@trungqn1890
Жыл бұрын
Hi. In where i live, room temp about 29-30*C at summer, so my a07 has been shutdown 2 time even it does not play too loud
@editorjuno
Жыл бұрын
@@trungqn1890 -- Understood, fair enough. I'm sure folks in situations similar to yours can benefit from your work. I also think they would like to know where you found that larger heat sink.
@graceMASTER777
Жыл бұрын
U bet....have never faced any shutdown like that even if the amp got heated ,which by the way is not much at all compared to few others. Offcourse driving it always like pedal to the metal would increase the temp way higher. Totally fine to see the mod and it surely does help in avoiding extreme heat.
@GurvanBHC7
Жыл бұрын
@@editorjuno Hey, does your receiver’s Amp have better sound than the Aiyma 07? I will soon buy an Marantz Cinema 40, and I don’t know if i buy 2 Aiyma 07 for the front LR and center, or for the surround and surround back… What do you think will give me better sound? Thank you in advance
@editorjuno
Жыл бұрын
@@GurvanBHC7 -- I've never owned a receiver of any kind, so I can't answer your question.
@gino3286 Жыл бұрын
Hi thank you for showing your very valuable modification If I understand well the copper plate is in contact with the chip below and the heat sink above? How please Have you considered a little heat sink with fan? Kind regards Gino
@trungqn1890
Жыл бұрын
Hi. There are no copper plate between the chip and heatsink. The aluminium direct contact to chip’s powerPad. If i not wrong, in new version A07, aiyima has upgrade bigger heatsink I don't like fan noise so I wouldn't appreciate that option.
@gino3286
Жыл бұрын
@@trungqn1890 hi thank you for the very kind and valuable advice You have done a great job indeed i would like to buy one but i am still undecided about buying just a board to make some experiments I could put the board and the psu in the same box thanks again and kind regards gino
@trungqn1890
Жыл бұрын
@@gino3286 There are some kinds of boards on the market, some is good like 3e but otherwise almost them dont have good quality components and finishing. Based on the amount of money you can consider
@gino3286
Жыл бұрын
@@trungqn1890 thanks again i see it's not easy But i would like to change also the volume pot for instance I will try one or two after reading some reviews Kind regards Gino
@trungqn1890
Жыл бұрын
@@gino3286 i also tried some cheap A50k volume pot and result is quite good
@user-hd8dn6vl3f Жыл бұрын
А не проще вентилятор поставить?😊
@OperatorCVK Жыл бұрын
Good day.Capacitors Fg and bp?
@trungqn1890
Жыл бұрын
Bp sir
@OperatorCVK
Жыл бұрын
@@trungqn1890 And Fine Gold?
@trungqn1890
Жыл бұрын
@@OperatorCVK yes but i changed to wima mks2 for coupling and silmic ii for feedback
@OperatorCVK
Жыл бұрын
@@trungqn1890O wow.That will better?
@Random_4400 Жыл бұрын
should've been how it came.
@991carreras3 Жыл бұрын
I do believe this mod is a waste of time&money chips are made to run at their specific temp range in order for them to be efficient. The chips in your PC or phone are always hot they are meant to be. My a07 runs a good 12hrs a day for months now and it's still going.
@trungqn1890
Жыл бұрын
Haha
@Knowbody42
9 ай бұрын
Chips perform worse and are less efficient the hotter they get. No they are not "meant" to be hot. They are just "allowed" to be hot, because cooling them better requires bigger heatsinks, which adds cost and makes them bigger and heavier.
@joicejewerly5579 Жыл бұрын
Fan is better
@trungqn1890
Жыл бұрын
Yes, fan is better cooling, but i dont like its noise
@haisonnguyentran7869 Жыл бұрын
BÁC CÓ BÁN KHÔNG Ạ
@trungqn1890
Жыл бұрын
Bán gì bác?
@phanvanbin3307
Жыл бұрын
Có bán lại bản mod đó không ạ
@itstinks1371 Жыл бұрын
My A07 has never registered so much as even slightly warm to the touch. What kind of use do others see that causes a heating issue?
Пікірлер: 41
I drilled a strip of holes down each side and a patch of holes on top right over the heat sink. I use a 48V power supply dialled down to 44V. works great
the mods looks great, hope that they also lift up the soundperformance-notch a bit
Is Nichicon Fine Gold cap good for signal input ? 💌
Why? Just use an aluminium block to connect it to the enclosure cover, this will result in direct heat contact with the cover (enclosure body).
Cool, haven’t seen anyone mod quite that much on a A07 yet. You changed a lot of parts. Did you find the upgrades worth it? Significant improvement in sound quality….? What was the total cost in parts for all of that?
The inductors, looks like you replaced them. What iductor are you using? Brand, model and spec please
@trungqn1890
Жыл бұрын
First, I replaced with coilcraft ver2923 oem, 10uh. After i replaced with 6,8uh. You can see it in my latest videos
What caps you use for replacing 2x 1200uf on supply?
@trungqn1890
Жыл бұрын
i replaced with nichicon FW 1000uf 63v
I own four A07s and have found that the "heat dissipation issue," while certainly measurable, presents no problem whatsoever in actual use playing music. I have two in my main system driving my ambience/surround speakers and never even had a benign output chip shutdown. I'm sure your mod will make yours run cooler, of course -- but, at least in my experience, it's a solution in search of a problem.
@trungqn1890
Жыл бұрын
Hi. In where i live, room temp about 29-30*C at summer, so my a07 has been shutdown 2 time even it does not play too loud
@editorjuno
Жыл бұрын
@@trungqn1890 -- Understood, fair enough. I'm sure folks in situations similar to yours can benefit from your work. I also think they would like to know where you found that larger heat sink.
@graceMASTER777
Жыл бұрын
U bet....have never faced any shutdown like that even if the amp got heated ,which by the way is not much at all compared to few others. Offcourse driving it always like pedal to the metal would increase the temp way higher. Totally fine to see the mod and it surely does help in avoiding extreme heat.
@GurvanBHC7
Жыл бұрын
@@editorjuno Hey, does your receiver’s Amp have better sound than the Aiyma 07? I will soon buy an Marantz Cinema 40, and I don’t know if i buy 2 Aiyma 07 for the front LR and center, or for the surround and surround back… What do you think will give me better sound? Thank you in advance
@editorjuno
Жыл бұрын
@@GurvanBHC7 -- I've never owned a receiver of any kind, so I can't answer your question.
Hi thank you for showing your very valuable modification If I understand well the copper plate is in contact with the chip below and the heat sink above? How please Have you considered a little heat sink with fan? Kind regards Gino
@trungqn1890
Жыл бұрын
Hi. There are no copper plate between the chip and heatsink. The aluminium direct contact to chip’s powerPad. If i not wrong, in new version A07, aiyima has upgrade bigger heatsink I don't like fan noise so I wouldn't appreciate that option.
@gino3286
Жыл бұрын
@@trungqn1890 hi thank you for the very kind and valuable advice You have done a great job indeed i would like to buy one but i am still undecided about buying just a board to make some experiments I could put the board and the psu in the same box thanks again and kind regards gino
@trungqn1890
Жыл бұрын
@@gino3286 There are some kinds of boards on the market, some is good like 3e but otherwise almost them dont have good quality components and finishing. Based on the amount of money you can consider
@gino3286
Жыл бұрын
@@trungqn1890 thanks again i see it's not easy But i would like to change also the volume pot for instance I will try one or two after reading some reviews Kind regards Gino
@trungqn1890
Жыл бұрын
@@gino3286 i also tried some cheap A50k volume pot and result is quite good
А не проще вентилятор поставить?😊
Good day.Capacitors Fg and bp?
@trungqn1890
Жыл бұрын
Bp sir
@OperatorCVK
Жыл бұрын
@@trungqn1890 And Fine Gold?
@trungqn1890
Жыл бұрын
@@OperatorCVK yes but i changed to wima mks2 for coupling and silmic ii for feedback
@OperatorCVK
Жыл бұрын
@@trungqn1890O wow.That will better?
should've been how it came.
I do believe this mod is a waste of time&money chips are made to run at their specific temp range in order for them to be efficient. The chips in your PC or phone are always hot they are meant to be. My a07 runs a good 12hrs a day for months now and it's still going.
@trungqn1890
Жыл бұрын
Haha
@Knowbody42
9 ай бұрын
Chips perform worse and are less efficient the hotter they get. No they are not "meant" to be hot. They are just "allowed" to be hot, because cooling them better requires bigger heatsinks, which adds cost and makes them bigger and heavier.
Fan is better
@trungqn1890
Жыл бұрын
Yes, fan is better cooling, but i dont like its noise
BÁC CÓ BÁN KHÔNG Ạ
@trungqn1890
Жыл бұрын
Bán gì bác?
@phanvanbin3307
Жыл бұрын
Có bán lại bản mod đó không ạ
My A07 has never registered so much as even slightly warm to the touch. What kind of use do others see that causes a heating issue?