A few important notes I included in the sister video that I neglected to mention here. 1. Tow vehicle is a 2020 F250 w 7.3 Godzilla 2. Test trailers have always been 30-37ft and around 7500-10000 lbs 3. This hitch is rated for a 1600lb max hitch weight and 16,000lb max trailer weight.

I can't thank you enough for taking the time to do such a thorough review of this hitch and others. I'm currently using the anderson but I feel I'm slightly too heavy for optimum performance with my Jayco eagle 284bhok. It's just not pushing enough weight back to the front tires. Everything else about the anderson I've liked. That being said this hitch has all the pros of the anderson but is just a much better design. I will be purchasing this hitch purely because of your review. Thanks again!

I now have over 1500 miles on my Continuum hitch and I strongly believe it was worth the price. One thing to note is the composite spring bars. These are far superior to any steel spring bars because they can be engineered to flex at different rates. The outcome is a much smoother ride. I have noted before that my DW who does hand sewing when we travel was not able to sew much of the time previous to this because of rough roads. With this hitch the smoother ride enables her to enjoy her hobby. As the video shows the hookup time and effort is the best of anything I have used and for those occasions where the TV must be angled to the left or right the advantage is even greater. As noted below part of the observing of different pressures on the gauge is the fact that your rig must be level for this reading to be the same. If you are on a surface that has plane of the trailer lower than the plane of the TV then there is less pressure on the hitch and spring bars and the gauge will read lower. I have in my experience with the hitch gone through side winds and other issues as uneven lanes or trucks passing and found no sway problems. For those of you who are looking for real experience to help you asses the hitch then I hope this helps.

@WanderingWeekends

Жыл бұрын

Yes, very smooth ride. As for pressure loss... I have lost pressure simply sitting in one place so while the angle point is well taken this wasn't the reason I've lost pressure. Temp maybe? I'm not sure how much 20 degrees would have on the system. Hopefully not much at all.

Your review videos are great. I have been looking at the B&W for a while and then stumbled upon your first video. I ordered the hitch before we went to pick up our new TT. First trip from Middlebury IN to Monticello KY experienced a variety of conditions from wind to rain to blue skys and calm conditions, along with all traffic conditions (Friday before Memorial Day). Camped for a few days then back home to NC. Totaling around 650 miles and feel confident in the hitch. Tow vehicle 2016 Ford F150 crew cab 5.0 and trailer 29’ Grey Wolf 22RRBL dry weight just under 5,500 lbs. Do love the fact that it will be easily adjustable once the motorcycle is put in the trailer.

@WanderingWeekends

Жыл бұрын

Great to hear! Safe travels!!!

I appreciate these reviews. Especially the hitch reviews. Already purchased the Curt Trutrack based on your review. Finally got our camper last weekend after over three years of waiting. Looking forward to getting on the road.

@BusaJohnny1

10 ай бұрын

How has the Trutrack done for you? What’s your truck and trailer setup?

@lancecrowe2565

10 ай бұрын

@@BusaJohnny1 been really impressed. I think that I overstressed myself while installing. It really wasn’t that hard, but it was closing time at the dealership. Just be able to take your time. Pulling a Zinger 398FB with a 2006 F250. My previous experience was with an older Equalizer with a different camper (similar size and weight). Like the Curt better.

@brandonsyatessr.3667

Ай бұрын

Keep taking your time... That's a valuable trait I'm RVing. A lot of mistakes could be avoided by one last walk around.

Thanks for the review. I almost went the for the B&W but wound up odering a Weigh Safe middle weight.

I finally got my B W a couple of weeks ago. The only thing I changed was the four bolts that hold the hydraulic cylinder, I used Grade 8 bolts, washers, and nuts. I have a camper over 12000 pounds.

We run the Hensley on our 21 GD 2600RB. Trailer sway is a non issue. It was expensive but I don’t ever worry about it. Hitch and go.

Great follow up video Cory thanks for the update 😊

@WanderingWeekends

Жыл бұрын

Always appreciate your interaction!

Who would have thought that a hitch would be exciting but you make me want to buy and try them all!

@WanderingWeekends

Жыл бұрын

They're getting heavy! Haha... maybe I will pass the baton to you...

Thanks for the video. Happy with my Continuum thus far. Hope your foot is OK!

@WanderingWeekends

Жыл бұрын

US Open and College World Series… I’m milking it!! 😂🤣

Ive been very intrigued by this hitch, maybe for our next trailer.

Great review. I like the live action shot. I'm really impressed with my b&w on the road. It has made my ride very comfortable with an old truck. You were right about not going wrong moving from the BO. I'm still getting used to the hitching and unhitching at angles/uneven ground. Very doable, but there are some things you have to watch and be prepared for. I also couldn't use the mount, it left the platform too low and it would hit the bars in tight uneven turns. (GA state parks)

@WanderingWeekends

Жыл бұрын

Enjoy that hitch!!

Nice review! This looks like a viable option to recommend to my people. -Maxx

It’s a nice looking hitch and does the job. However I’m a weigh safe middleweight owner thanks to you and I love it! Hope I made the right choice! Looking forward to seeing the battle review.

@WanderingWeekends

Жыл бұрын

Tough to beat… 10 hitch showdown coming soon!

@hiking7521

4 ай бұрын

​@WanderingWeekends great videos, anything new for 2024? I'm holding off for the new design. Cheers

Nice, GREAT Information. I have 5th wheel GD 2930 so I don’t use pull hitches. But I like watching these videos.

@WanderingWeekends

Жыл бұрын

I appreciate you watch!

I have also experienced big swings in hydraulic pressure. For me this happened when going from low elevation hot climates to high elevation nearly freezing climates and vice versa. Not sure the how temperature affects the volume of hydraulic fluid but my guess is the volume deceases with lower temps and therefore the pressure decreases too. I would adjust the pressure at each fuel stop to accommodate for pressure swings. Otherwise this hitch drastically improves ride and handling of my rig and inspires both my wife and my confidence while hauling.

How does hooking up on an angle work? Does your truck have to be perfectly aligned with your trailer when you back up in order for the jaws to fit in? Can your truck be at a 30 degree horizontal angle and still be able to hook up? I know with the anderson if you're angle is > X degrees then you need to take a tiny bit of weight off the ball, then adjust the appropriate chain to "pull" the receiver ball into the correct position, then you can finally hook up both chains and put full weight on the ball.

Great final review. Love the ease of use but my driveway is on an incline so ground clearance would definiteky be an issue. We've also camped in some state parks where that would be problematic. Keep up the good work!

@WanderingWeekends

Жыл бұрын

Definitely takes a few points away. We will see long term of it becomes an issue.

How will the Hydraulic work in the winter time, i live in the north, sometime I leave when it is cold when i leave for the south.

Although you would have to pry my Propride 3P from my cold dead hands, because it's so awesome, I still enjoy watching your videos and learning about what's available. Keep up the great work! I'll keep refering people to your excellent videos.😁

@WanderingWeekends

Жыл бұрын

So appreciative!! I've seen you share our stuff many times!

@DR-ur4zd

Жыл бұрын

This hitch seems more focused on the weight distribution part whereas propride shines on the sway control part. A mash up of this one with the ProPride would probably be the best hitch all around I think.

I was tempted to go with this hitch because of its simplicity but that hydraulic system looked to be a real potential point of failure. I ended up getting the ProPride hitch and other than hooking it up, I have been very happy with its performance.

@Abc-kf4qx

9 ай бұрын

I’m told one of the main advantages of the B&W is that you can back up with it on, is that true?

@dodgeguyz

8 ай бұрын

@@Abc-kf4qx You can back up with any type of hitch. Just need to not jackknife.

Good review with pros and cons. I'm surprised that the sway control works as well as it does. As for clearance, it's more than my ProPride, which is like 8" or less from the ground, and I take my jack shoe off when hooked up, so it doesn't hit. ProPride needs to figure out how to incorporate this tech. It's weight distribution is a weak link.

I am in the market for a WDH and I am not sure which would be better, the B&W Cont. or the Weigh Safe for my Micro Minnie FLX2108Tb (Just 5500 GVW)?

I have this hitch and have used it now 4 times. I too thought I was loosing pressure but it really came down to how level you had your truck in comparison to your trailer. If they are angled when you put pressure on it and then compare it to when they are leveled together, the pressure changes as the angle between the trailer and truck changes. This is what I noticed at least. I have not done specific testing. It did perform great all in all though. So far, I love it. I too can’t use their hanger. To keep the hitch off the ground, I just wrap a bungee around it to keep it up when storing.

@WanderingWeekends

Жыл бұрын

Mine has lost the initial pressure just sitting but generally it holds after the initial loss.

@robertjf9900

Жыл бұрын

@@WanderingWeekends I’ll be on the lookout for that but haven’t noticed it. So far so good.

@billtate488

Жыл бұрын

I have about 1500 miles on my Continuum and at first I was concerned about pressure loss as well. But as Wired1236 noted if you are not on level ground the pressure on the spring bars will change and thus affect the pressure on the gauges.

what is orange bucket trailer foot jack thingie? I don't see it listed in your products in the description.

I have questions on long-term durability.....hydraulics require maintenance that most wont perform..... hoses and pumps fail and as you said you already experienced pressure loss..... with no direct mechanical connection on the bars to maintain the pressure on them i would be very hesitant about using it

I posted in the last video that I purchased one for my in laws and they still love it. One specific note on ground clearance for a very specific use case: - F-150 (half ton) with the front return set correctly based on the ford tow guide - A 24’ TT that is within the weight range but on the LOW end - It’s a jayco, which has an under slung hitch, which is a different SKU than a standard hitch. - Only need around 1300 psi for correct distribution. With those factors it sits lower than a normal bar would and has scraped a few times where there is significant articulation between the truck and trailer (driveways, campground entrance)

@WanderingWeekends

Жыл бұрын

This is good to know. B&W says they are keeping an eye out to see if this becomes a significant issue.

Question: On an F350 dually towing, a 9,000lb 30ft travel trailer, if the front wheel measurement from ground to top of wheelwell difference is zero, do I still need a weight distribution system? Thanks for your great channel!

@WanderingWeekends

7 ай бұрын

Even if you didn’t need the weight distribution I’d still use the sway control many of these hitches offer. Some better than others.

I see a lot of ground clearance has been removed compared to say the Andersen hitch without measuring to compare it looks to be somewhere between 1 to 2 inches closer to the ground at its lowest point than on the Andersen.

I hope this one makes it into the Australian market!

How is it backing up with this hitch? What size drop is that on your truck?

good video on a system I hadn't heard of yet.

@WanderingWeekends

Жыл бұрын

It’s legit!

Thank you for actually showing the part where you had to move the truck slightly to lock the ball. I've seen people who are new to towing struggle and think that they are doing something wrong because no one ever shows that so people start to think if they can not immediately lock the coupler, they have done something wrong. I know it may not make the prettiest video, but I for one appreciate real and actual over those that edit out the real possibilities. Thank you for another great review. I guess the real question that remains, and I'm assuming you will be answering when you do your rating video, will this be remaining on your trailer, or will you be going back to the Weigh Safe?

@WanderingWeekends

Жыл бұрын

I’ll keep that in my pocket for a few more days. 😜

@WanderingWeekends

Жыл бұрын

and yes, I kept that part in on purpose. All part of it!

@sssophiesmom

Жыл бұрын

100% agree with this comment about how you release the emergency brake to get the tongue to lockdown. I've seen and heard too many people on forums say that they take a hammer to it etcetera. In fact I had done that once myself very early on until I found out about this trick. It works almost every single time

Looks like a really nice hitch but the concern of a hydraulic failure on a long trip would keep me from buying it.

@riccochet704

Жыл бұрын

My thoughts exactly. I've seen plenty of hydraulic failures in a number of products. And those lines don't look confidence inspiring.

Looks like a really good hitch and very quiet too. Then i saw the price tag. 😅

Enjoy your videos on weight distribution hitches. The "stop" nut your refer to on the BW appears to be a lock nut.. Close the valve then tighten the nut ~ 1/4 turn to lock it in place. And a question, where does the BW rank in your ratings, number 2, 4, etc.?

@WanderingWeekends

11 ай бұрын

It ranks #3 but it’s very close to #2. Great hitch and very easy to operate.

Good video. Much appreciated! I'd like to switch from my Andersen WDH to that Continuum but I've an odd issue. In order to fit the trailer into its space I use the Trailer Valet RVR-9. I think that would be problematic with the Continuum but I may be able to figure out how to use bungees to keep the thing up off the RVR-9. One thing I really dislike about the Andersen WDH is that if you are backing in your trailer and the tow vehicle and trailer are not nicely line up straight with each other it can be a real pain to get things hooked up. I'm going to have to sort out whether the Continuum has similar issues (I'm guessing it doesn't).

@sssophiesmom

Жыл бұрын

One question I have always wondered about the Anderson hitch...you mentioned hard to put back on if vehicle amd trailer are not straight... Could you simply hitch up trailer but not attach the plate, then pull forward til vehicle and trailer are line up straight, and THEN attach the triangle plate? I dont have one yet but plan to buy one next yr. I am never straight on when backing into a campsite. I always am angled to put trailer exactly where i want it. Thanks for your thoughts

@oldguy1030

Жыл бұрын

@@sssophiesmom The fix is a little different from simply hooking up the hitch and pulling forward. 1. If the plate is angled just a little off then you can simply hook up the plate and tighten things as per normal. 2. If the plate is angled a lot then that doesn't work and you can't pull it straight or safely hammer it into position. The fix is to keep the chain fastened to the wing which is most pointing back toward the trailer. Disconnect the chain from the wing which points more toward the tow vehicle. Then you pull forward and turn away from the chained side until the wings have straightened enough to hook up the other chain. It is somewhat counter-intuitive but it does actually work. So the above actually is a fix but it isn't actually even as straightforward as it sounds (or does not sound) above. If you don't have a broad expanse of space in order to make the requisite turn you are kind of out of luck. I hooked up at home and if I tried the turn as I came off the concrete in front of the garage and tried to make the required (in my case) sharp turn to line things up - I block the entire rather busy street. I had tow it around until I could get to a less-busy street and blocked that street. And understand, to get things sufficiently lined up I had to turn so sharply that there were just a couple of inches between my truck bumper and the frame of the trailer. The Andersen WDH performs pretty well for me when I'm out on the road but the wing plate problem has me unhappy enough to want to switch.

In review videos about sway control hitches, I would really like to see the reviewer position a camera so that we can see an overtaking semi in the sideview mirror plus the steering wheel and the actions that the driver has to use on the steering wheel to correct for the truck suck. The camera on the bumper is cool, but it does not convey any info as far as sway from a passing semi.

@WanderingWeekends

Жыл бұрын

We did that a few vids ago... in 40mph winds.

Looks great. I wish they would make it in 2" ball.

@WanderingWeekends @ 12:14 of the video does the hitch hit the drop part of your shank during that turn or is there enough clearance for it to pass by?

@WanderingWeekends

Жыл бұрын

I don’t believe so. No scarring so I can’t imagine it hit.

Thanks so much for the answer on my F350 with no need for weight distribution, but add it for sway. Great point! Would you mind answering another question. What would you think of combining the Gen-Y torsion hitch with the weight distribution adapter along with this great B&W weight distribution system? Thanks for your honest channel. Really enjoy it!

@WanderingWeekends

7 ай бұрын

I sure appreciate you watching. I haven’t used the Gen-Y so I won’t comment on it. I will say I’ll have a new video coming out on the B&W. I was disappointed with it on our larger prototype.

@dennisd7292

7 ай бұрын

Thanks so much for answering. Will be looking forward to your update!

@davidb6194

6 ай бұрын

@@WanderingWeekends Curious to see the new video on the B&W. Was thinking about it for a 32' Outdoors RV to be towed by Ram 3500. May consider something else if you have concerns with a larger trailer. Thank you for all of your awesome content. Enjoy and appreciate it 🙂

I can't imagine pulling a 16K bumper pull. Has to be rough. I have a trailer about half the weight and that's as high as I am willing to go... but do pull with an F150 rated for 10,500# trailer, but it does very well and the 26 MPG not towing is sweet. I have the Andersen 3386 and love it.

About the hydraulics! 3 MAJOR concerns. 1st if the shutoff is a needle valve they tend to get ridges on the needle and start to bypass. Why would they have the valve sticking out in harms way. Very possible to get broken off or damaged beyond use. Right above that is the little gauge which is connected in the pressure circuit. If it takes a hit, the bourdon tube inside may rupture. This component is brass and not much thicker than a soda can. I would suggest shielding the pump or moving it to a safer location. It looks like a nice little pump it just seems exposed for damage.

My question is where did you get the shank that is 2.5" for this product as I don't see a reducer sleeve on your truck, and I only am finding the 2" version online for the 2 and 5/16 ball.

@WanderingWeekends

7 ай бұрын

Hmm… this is what they sent me. I’m surprised it isn’t online.

Another great video! Appreciate the follow-up. I just installed one and posted it on Facebook (I really appreciated your feedback there!) and the question about the hydraulics has come up a lot. Several people have voiced reservations about that. I'm curious to know if you've talked to B&W about this at all and their response? I also wonder if they've considered putting together an emergency repair kit?

@WanderingWeekends

Жыл бұрын

It is a closed system so I'm not sure.

I have a 31 footer I pulled no problems without a weight distribution hitch. Wanting to get one for when it’s loaded. Out of the weigh safe and this one which one would you recommend? I’ve gone back and forth on them. Love the propride but don’t want to drop $4k on one.

@WanderingWeekends

Жыл бұрын

What are you towing with?

Just bought this hitch from E-Trailer, hope it is easier to hitch and quieter than the equalizer I have.

@WanderingWeekends

Жыл бұрын

It is silent and easier!

Any issues hooking and unhooking at an angle? I know my Anderson can be a pain if your not at the same angle as you where the last time you hooked or unhooked.

@WanderingWeekends

Жыл бұрын

10-15 degrees either way is not a problem. I haven't tested it further than that. Likely no.

That's the best hitch I have ever seen.

@WanderingWeekends

Жыл бұрын

Top 5 for sure.

Nice Video appreciate the work. Have you ever tested a Reese Dual Cam?

@WanderingWeekends

Жыл бұрын

Unfortunately they won't respond to our requests.

@josephgiattino389

Жыл бұрын

@@WanderingWeekends Well that sucks.

This is a great review! Would you choose this or the ProPride? Looking to get a monster hitch for the new Brinkley ZAir295, worried the ProPride might not fit so this looks like a great option.

@WanderingWeekends

5 ай бұрын

I need to do an update video. I was very unhappy with the B&W on the longer trailer we have now. I may shy away from it on the 295 for sure. That is a heavy rig.

@chrisslater1936

5 ай бұрын

@@WanderingWeekends Thank you! I needed that feedback. I was down in Tampa trying to see how a ProPride would fit, might need some tweaking but I think that's the best bet.

@WanderingWeekends

5 ай бұрын

I looked at that exact issue. I do not think it’ll work with that propane box. Let me know if you get it to fit. I would take a look at Weigh Safe as well.

Corey They attempting to compete with Weigh Safe? I love my WS weight distribution hitch, but dialing in Weigh Safe “safe zone” can be a pain at times. Is this easier then WS?

@WanderingWeekends

Жыл бұрын

I’ll definitely compare the two soon.

@malifestro3319

Жыл бұрын

I'm not an owner of that one. What is hard about it? Don't you just turn the thing a few times. Love to hear your take

@anthonyk8716

Жыл бұрын

@@malifestro3319s an example; my tongue weight is 1400lbs. According to the weigh safe app, my safe zone weight is between 3400-3800 which my understanding is; I torque/screw until the gauge in the window shows I’m equalized either at the minimal of 3400. middle or highest safe zone. Reaching these safe zone I turn clockwise, which becomes very difficult with each turn considering I’m starting at 1400. Hope this makes sense. Thanks

I have gd 2800bh. Out of all the hitches what would you choose today knowing everything you have tested? Thanks!!

@WanderingWeekends

Жыл бұрын

I’ll be doing that video next!!

@joecairo9818

Жыл бұрын

Great! Only one left I’m curious about is the shocker air equalizer hitch

The only potential problem I see deals with the safety chains. Looks like they may be pinched or not long enough with this hitch depending on how deep the tow vehicle hitch sits

@WanderingWeekends

Жыл бұрын

They are on the fence of needing extensions. I am using about 4 extra links.

My trailer is approx. 10,000 lbs. Is there a recommended range for the weight of the trailer for this?

@WanderingWeekends

Жыл бұрын

16,000lb gross 1600lb hitch I’m dumb… that is crucial info I left out. Please listen to nothing I say!!!

The B&W or the weigh safe for better sway control?????? Thank you

@WanderingWeekends

Жыл бұрын

I’ll answer that question very soon!!

Hydraulics don’t expand nor compress! (Paschals law) Sounds like you have a leak, (most likely cylinder seals leaking by internally if you don’t see any oil on ground). Pressure will leak down to counter pressure. What I mean by that is if it is leaking/bypassing, it will only leak down to point that it can hold back. Work with hydraulics every day at paper mill and if it did expand or contract, we would be in serious trouble.

@danmoseley8547

Жыл бұрын

Also…thanks for the videos!

@WanderingWeekends

Жыл бұрын

I think they’re meaning hoses and seals. Either way that was their explanation.

In an emergency if the hydraulics fail, you could use a chain in like a large 10,000 pound cargo strap to pull it back up and lock it off to give some weight distribution back to the system till you can get stuff repaired

It's a good design, but the hydraulics and, really, minimal sway control are limiting factors here. That's not going to reduce sway much at all. Proper setup with it will.

How often do you have to check the hydrolic pressure on this hitch?

@WanderingWeekends

Жыл бұрын

I was keeping a close eye on it for review purposes but it should hold all day.

@shannonyork5300

Жыл бұрын

@@WanderingWeekends Do you think the bleed valve/lock nut configuration needs to be redesigned so it does not loosen?

Great video! I am certainly one who is concerned with ground clearance, as we are 80% boondock camping, and we have gone through some rough areas. I have 28' Toy-Hauler, and would love this B&W, but would actually like to see video of someone taking this off road with actual dips (unmaintained) roads.

My big question is. The ground clearance for half ton trucks. TUNDRA, F150, and so on.

@WanderingWeekends

Жыл бұрын

Yep, definitely a concern. Some of that depends on the trucks suspension and the tongue weight of the trailer as well.

@billtate488

Жыл бұрын

With my experience with a half ton there has been no issues with ground clearance in campgrounds, speed bumps and entrances and exits.

@ride-electric

Жыл бұрын

Ground clearance with this hitch looks to be tied into what style A frame you have. Is the A frame welded under the main frame or does it run through the frame. There will be a 5-6" difference between the two. Imagines run the A frame under the main frame so thats why there's only 10" of ground clearance. Anyone with a through the frame A frame will have around 15-16" of clearance. Doesn't have much to do with the tow vehicle.

The leaking is the O-Rings in the handle cylinder

Can you open your tailgate fully with the trailer hitched up to the Continuum?

@WanderingWeekends

Жыл бұрын

Unfortunately no.

@johnand

Жыл бұрын

@@WanderingWeekends I just installed the B&W Continuum hitch today. I had previously clocked my tongue jack 90 degrees and was able to open tailgate with Andersen WDH. I am happy to tell you the tailgate fully opens and clears the tongue jack just fine with B&W Continuum hitch and clocked tongue jack. I have a 2022 F250. I suspect your new 2023 F250 will clear too if you clock the tongue jack. Thanks again for your recommendation on the B&W. So far, so good.

So except for the dragging and the leaking, it is a great hitch!

@WanderingWeekends

2 ай бұрын

It hasn’t dragged or leaked with me… but it did have a bad showing on a busy interstate after this video.

I know you mentioned there's antinsway technology built in but I wish someone could explain it as opposed to "it just works'. I asked the same question when etrailer put the video out but didn't get a response 😕

@WanderingWeekends

Жыл бұрын

The shank inside the head of the hitch is providing friction.

@mikep8085

Жыл бұрын

@@WanderingWeekends Is it similar to how the Anti Sway works in the Andersen hitch?

I have two concerns. 1) Ground clearance with F150, 2) occasionally campsite slopes front to back requiring the trailer tongue be dropped to the lowest point to level. Wouldn’t this hitch prevent this? Cory, you have the best hitch reviews, period. Thank you so much for taking the time to do these. You make me a more informed consumer.

@WanderingWeekends

Жыл бұрын

Yes, I don't think the tongue jack can be lowered completely. MUCH less of a problem that the ProPride though.

@ronhayes832

Жыл бұрын

@@WanderingWeekends I’ll keep my WeighSafe True Tow…best hitch ever!

@Berrypancakes229

8 ай бұрын

⁠​⁠@@ronhayes832 my husband has the weighSafe tow hitch and he loves it.

Any discount codes avaialble for B&W?

@WanderingWeekends

11 ай бұрын

Unfortunately no 🙁

@mattstevens7802

11 ай бұрын

@@WanderingWeekends Thanks, I ordered one anyways then. Appreciate your videos, it's been very helpful. We are towing a 2910BH behind our Grand Wagoneer and the equalizer the dealer pushed on us is quite noisy and not great. I wish I'd seen your videos sooner, I would have passed on the dealer hitch!

Nice job god bless

@WanderingWeekends

Жыл бұрын

Thank you! You too!

Are you able to open your tailgate?

@WanderingWeekends

Жыл бұрын

No, dang it!

@richmorris9795

Жыл бұрын

@@WanderingWeekends hopefully they will come out with an extended shank like equalizer did so you can open the end gate... that is a major thing for me...

As a physics engineer, it's a great idea. But it has 2 issues ground clearance and complexity. Number one rule in design ...KISS concept. The hydraulic part of this design will be problematic.

How about video going over railroad tracks or dips?

@WanderingWeekends

Жыл бұрын

The bumps at 12:41 are equivelent to a semi rough railroad track crossing.

@EvenaGirlCanDoIt

Жыл бұрын

@@WanderingWeekends I was looking for the stress pit n the trailer a gram when going up a small quick drop hill. Kind of like when going into gas stations

its interesting and looks super easy. 1 major flaw i see im kinda sad to say. makes for a super easy hook and book theft. loop over a ball and off you go. probably more stable than the chain pull thefts. :( the no low nose is also an issue for a few sites up here in the north east for sure

@billtate488

Жыл бұрын

The spring bars can easily be fully removed from the trailer by removing one pin. Then you are back to the same security as any other hitch.

@badpewterz

Жыл бұрын

@@billtate488 good to know, i was not aware of that aspect. thank you

Kinda seems like a mix of a gooseneck and fifth wheel on a much smaller scale.

Can you open your Tailgate?

@WanderingWeekends

Жыл бұрын

No ☹️ I mentioned that in the install vid but definitely should’ve mentioned it here too.

@stevevetter8045

Жыл бұрын

@@WanderingWeekends thanks and again as always Great info and video

No thanks! I’ll stick with the Reese Dual Cam that works great!

Clearance my not be an issue for you and your F250. Put it on a F150 ......

@WanderingWeekends

Жыл бұрын

Yep, definitely a concern. Precisely why I show the measurement twice in the video. B&W tells me they are keeping an ear out for widespread issues.

Your reviews are great, now go back and do them with a 1/2 ton 😂😂😂 please

@WanderingWeekends

10 ай бұрын

Nope 🤣😂🤣 Seriously though, I can’t imagine performance wouldn’t translate similarly to a 1/2 ton. One would likely feel a little more movement but you’d still have an idea of which hitch does best.

when i saw the debut of that thing i called it a failure out of the box because of the hydraulic. Why? Because hydraulic pressure is affected by temperature, which changes with ambience and changes fluid temputere with work ( while you're driving). The 3rd factor that affects fluid pressure is elevation changes. IMO. That makes that hitches performance unreliable, unpredictable and potentially dangerous. As you're experiencing in your review.

@scotimotti

25 күн бұрын

Or you could just tighten the bleeder screw...you know kind of a follow the instructions kind of deal.

I can tell you from experience that this hitch doesn't help with swaying. I purchased and installed this hitch before going on a road trip. I was at times holding on for dear life because every time a vehicle would pass me from the rear it felt as if I was being pushed of the freeway. I spent a lot of money for this hitch thinking it would perform asked advertised and I'm totally disappointed

@WanderingWeekends

Жыл бұрын

Oh wow, that’s disappointing to hear. I towed with this hitch in 30-40mph gusts and it did very well. How is your hitch weight? Are you rear heavy? I’m very interested to know since this hitch did so well for me.

Easiest hitch you have ever used? What was wrong with the Gen-Y

@WanderingWeekends

Ай бұрын

I have not used the Gen-Y

*PromoSM* 💞

Looks like it is leaking hydraulic fluid

@WanderingWeekends

9 ай бұрын

I can’t find any.

No thanks too complicated.

Blue Ox is the way to go

@WanderingWeekends

Жыл бұрын

*spits out coffee* 😂🤣😂🤣😂🤣