I am a 5th generation farmer in NW Iowa. I just started full time farming last July so take my advice for what it's worth. I have been doing most of the tillage since I learned how to run a tractor. We do all of our tilling in the spring. We have always used a mulch finisher and we love it, it does a really good job for us. If you are interested, we just updated ours with a bigger one this year. We currently have our last one listed for sale. It's a John deere 726, 24 foot wide, new hydraulic lines 2 weeks ago and was ready to go to work. I would love to help you out if you are interested in buying one. If you read this and have any interest please reach out to me and I'll get you my contact information. Anyone else who sees this and knows Grant personally let him know. Thank you and keep up the good work, I absolutely love your videos!

@granthilbert5632

2 жыл бұрын

Thanks! Not sure if I'll be looking for a Mulch Finisher yet. I may look for an old disk, and keep FC, or look for a good used VT Tool. It helps that I have a lot of neighbors who rent out some of their implements. It works really good that way!

@kdaniel59

2 жыл бұрын

@@granthilbert5632 sounds like you have a plan! I just started tilling today, going good so far! Should be planting corn this week. I'm excited to see how your field work progresses 👍

@smittycreations5475

2 жыл бұрын

@@kdaniel59 those mulch finishers are amazing we have a 30 ft jd 726 we farm about 2000 acres in northwest ohio and it gets the job done very well

One thing we do for whenever we do corn on corn is sell the stalks off the field. So basically after we combine someone pays us and they come in and chop stalks bale them and take the bales then you have very little left of the stalks. Just an idea for you.

Don't have to get fancy. Just run threw it with an old school disk for this year.

Thanks for planting Becks that what our family sells and plants

In west texas we call those “witching” rods. That’s how we find streams underground for our irrigation wells.

For the algorithm. Likes, comments, shares, and subscriptions help your content creators more than you realize. Keep it up Grant!

I’m glad I watched it to the end because your plan is exactly what I was going to suggest! Farmers really like helping each other.

our neighbor has an 7.5 inch spaced international disk and he goes over the field in the fall then again in the spring and then plants and it leaves the field nice and smooth

I think you made the right call. Running the VT will do wonders. Keep up the good work.

Love your enthusiasm

I am a farmer from Wisconsin, we do most tillage in the fall with a moldboard plow we have been doing it all my life and for us it works good with getting rid of the corn residue.

Grant I recommend a McFarlane reel disc, we run one on our no-till farm in Tennessee and it works wonders, it chops the stalks into bits and pieces and still spreads them out without burying them, I sirously recommend looking at a 25ft, they pull hard so wouldn’t go too big

Corn stalks and field cultivators don't mix well hardly ever, we always hit ours with the landoll disc and then sometimes you can use a field cultivator but better just hitting it again with the disc

2 ways to weld on a diesel tank. The way you did it and absolutely full of fuel. I've done the later after the bolts that hold the seat suspension rusted/broke off on our Allis Chalmers 200. Vented the fuel tank and went at it. Fumes are flammable and absolutely wouldn't try that on a gas tank, but they say diesel will help keep the steel cool.

Hey Grant we run a old 1600 cultivator on are corn ground up in Manitoba with lots of stocks and it works best to cultivate on a 45 degree angle to the rows so you’ll be cultivating on an angle, it buried trash way better and we try to run the cultivator as deep from 4-6 inches

Love the videos. Take me back to my farming childhood. Tell me though how do you manage to stay clean and always so presentable? I always ended the day with more grease on me than the equipment! I wish you both the best of success.

You might consider getting some chopping rolls for your corn head. That would downsize the corn residue quite a bit, and it would be fun to watch you take on and put off snap-n-rolls 🤣🤣

@granthilbert5632

2 жыл бұрын

I'll check them out! Sounds like the install might be a pain the *ss :)

That was an expensive mistake by dad. Glad he didn't get hurt

I’m so glad field work is finally started!

As you said, it's probably a good idea in the next fall to run a vertical till to chop the stalks and then run the disc ripper to bury the stalks.

Hello from France. Always a pleasure to see your videos 👍

what we do for corn is run the vt landoll over the corn residues or a try tandem and then for beans you can usually get away with just going over it with the feild cultivator

You should get a heavy disc. It'll chop up the stalks and also bury some of the trash. Its an extra pass, but in my experience, the soil responds pretty good to it

We chop our stalks every year. But we bale them too.😁

This is my first year around them, but all 3 planters have them and I’m very impressed! Can definitely tell a difference when planting corn then dropping the bean rows with the ordinary rubber wheels on the corn planters to plant beans

Life is so much better after being flung off the merry-go-round of tillage. It's not a yield enhancing event. Plenty of room in the no-till playground...add covers and life gets even better. Good luck Grant, I enjoy your content. We failed at tillage too....no yield gain here.

Well Grant, that was some entertaining, but what a cluster f___! I could not have done any better. Thanks for sharing your triumphs and tribulations.

Great Video Grant

Plowing gets rid and puts a lot of residue down in the soil and gives you a nice bed to plant once rolled or sumod.

We have a Salford we run through our corn ground once in the fall and once in the spring. I also would like to say never reuse the old boots on the shovels. The heads can get so warm they will start Falling off and always wear gloves when changing I have sliced my finger on the heads many times

A lot of guys here in Kentucky run a disc over the stalks in the fall. Then vertical till with a rolling harrow running tandem in the spring. Seems to work pretty well at getting the trash under control. If they are strictly no-till they will just run a rolling harrow or Diamond harrow across the stalks then plant into it.

Keep up the great work

I run our field cultivator on my family’s farm and on the second day of pulling it this year I had a hydraulic line blow out of a fitting on the rolling harrow that I tow behind the cultivator.

Rolling basket for sure on corn residue. I enjoy your channel.

Loving catching your videos, reminds me of learning when I was a teen on the farm. Advice I have for you: 1) Never put your hands/fingers on the bolt heads of worn points when zipping them off. They become sharp as razor blades with enough wear. I had one spin and cut me through leather gloves before I learned. Use some leverage from the front of the point if needed to keep from spinning. John Deere offers a quick change system that is honestly worth it. 2) You need to grind your metal bare of rust/paint to penetrate the weld. What you have will break and likely to still break with a good weld. 3) You touched on each one of these as I was typing. Fall tillage pass with a VT etc will incorporate that trash better for the spring and they'll decay easier. (Great plan now too!) You look to be piling in front of your drag harrow. There should be a tension adjustment, probably chain length on that model. (You found it!) It should really just tickle and level. The cultivator depth looks deep in my experience. That'll pull more root ball up. Depth changes by soil types. Maybe chat with some local guys about depth tips. Definitely work it on a slight angle. 45 is more severe than we do, we prefer a 15-30 ish. Straight enough to be efficient but offset enough to distribute trash and work. 4) Can't wait to see your planting!

Get an old glencoe soil saver. We called them a disc chisel. They work great. We have had one forever and still use it on headlands periodically.

you two are learnig as you go, and your doing a really good job of it

grant with this much residue u may wanna look into an actual cutter disc implement vaederstadt has one that looks like a cultivator disc but it also chops up the residue real nice for when the soil animals maybe dont do it enough

Grant, something you may consider… Spend the $2000 to get a new fuel tank. Your tank might be structurally sound currently. However, it will be a nuisance and time consuming, and it will nickel and dime you. Also, it is better to have those up in the air, so gravity can help drain the tank fully, and you draw from the fuel at the bottom first. What happens with styles like you have, the fuel never fully drains and old fuel keeps mixing with new fuel. Just something we learned on our farm… just some food for thought. Fun vid…

Them closing wheel are pretty nice. We run them on our farm but they are a pain to put on. At least for us they were.

I highly recommend Calmer Corn Rolls on your corn header. My dad's been doing corn on corn with deep ripping and mulch finishers for about 20 years and Calmer rolls have really helped take care of the leftover trash.

@granthilbert5632

2 жыл бұрын

Will check them out. A lot of people have recommended them!

@Call-Me-Ottwa

2 жыл бұрын

@@granthilbert5632 They seem to work excellently especially in heavy soils with that tillage combo like we have in Illinois.

We call them witch sticks in Ontario Canada , basically water has an electric current so the sticks always follow the path of the water .We use them to find watermain when we are doing street work locating utilities . You can just use two bent coat hangers too haha . Works great if you know what you are doing .

Should look at the Deere mulch finishers they have disk blades up front that you can raise or lower if needed. Or some of the vert till tools

A good way to check for water lines is to wait after is rains really hard then get a view from the air, and wherever it starts to dry first is a tileline

We always ran field cultivators in rice stubble, with no harrow on the back. Seemed to clear the residue pretty well.

Hey Grant! When we still ran a Deere corn head we switched to Calmer snap rolls on the head. It helped tremendously with trash. Did a lot of cutting on its own. We were able to chisel or rip and run a field cultivator with no issues at all. Doesn’t rob much power from the combine and you’re already making the pass

Excited for planting season to start, hope this year is even better than last year's decenr yielding down corn so Excited to follow along

It very hard, just starting out, to have all the tillage tools for all the various conditions. I might have all the different tillage toys I really want (used, of course) by the time I retire.

I help farm in northern Iowa where we have lots of corn stalk residue after combining. I run a great plains 24' turbo chopper over all my corn ground in the fall first. the turbo chopper works well cutting and chopping up the residue.it only goes about 2 1/2 inches deep so you can run 8 to 10 mph. After I use the chopper, I go back over the cornstalk with a Sunflower 4412 disc ripper. this has disc in the front and behind the ripper shanks that you can adjust to help bury the residue. When the field is done, there is a little residue on top but in the spring we are able to run the turbo chopper over it again and have a great smooth and clean seed bed for beans. If we are going corn on corn, I run a 44' great plains discovator. This has straight cutting blades in front of the sweeps, drags, and rolling baskets. This will bury most of the remaining residue. Good luck with all your trash, we used to have that problem until I went to this tillage.

We call that witching down here. I've used hangers to do the same. And when putting weights on we always take off a fork so less of a risk of stabbing a tire

to get rid of a lot of the residue it helps to brush hog your feilds that will be corn on corn then rip it then cultivate it. It seems to help us a good bit on our farm

Love farming!!

If your looking for a good welder starting out thay will last a long time and be versitile get the Eastwood MP200i, I've had mine for around 2 years now using it stick and mig weld and it works awesome around the shop on farm equipment big or small! The best part is it's not super expensive for what it can do!

I'm not joking, but I've heard that it's actually better to weld with a tank full of diesel than an empty one.

@jagtaylor6538

2 жыл бұрын

Ya cuz you need air for a fire and if the tanks full there’s no room for air and a fire wont happen

@edvinvensryd3958

2 жыл бұрын

@@jagtaylor6538 sounds about right👍🏽

@bfd1565

2 жыл бұрын

@@jagtaylor6538 Inorder to start a fire you need 4 things. Oxygen, heat, spark and combustible. The fire triangle we were taught is incorrect.

@Chandlersaalf

2 жыл бұрын

Well if you have a death wish the be my guest

@tytheboss8528

2 жыл бұрын

@@bfd1565 not necessarily. You need oxygen, fuel, and some sort of ignition. The ignition could come in the form of heat or a spark.

You should get a stalk chopper that’ll definitely help when you get to tillage.

Learning as u go

We had that same cultivator. Called it the dump rake

You can use hangers for the same result to find the water lines and electric. Metal hangers of course.

On your shank welds, tack both sides before you weld it all out. When metal gets hot it expands and pulls, which is why you had such a big gap on one side.

On the hitch looks like you could loosen those 2 bolts a put a washer or 2 inside the clevis on top of the spacer and it would work fine

Grants - Some of our corn farmers around here burn their fields (stalks & residue) every few years when the field gets so full like yours. I don't know if you all are allowed to burn but they do do it here in Louisiana.

Hey grant, I have a suggestion for you, instead of ripping ground up you should get a rake and a bailer and start selling some bales and then rip it up

Ever thought of burning your corn residue off as a last resort? I’ve seen a few down here in south georgia burn the fields off. great job keep the videos coming

You should usually deep rip beans in the fall before it freezes and then field cultivate(fc) in the spring. Rip at an angle on way then (fc)in the opposite direction but at the same angle. Also you can’t do anything to stop corn plug ups even in beans you’ll get them but not as bad.

Re: Learning to weld. The Lincoln tombstone you've got is a great place to start. I've got a 50 year old one that I still use occasionally. Learning to weld is about puddle control. Stick welding or Oxy Acetylene welding will teach you this. If you become proficient with stick or oxy you'll find other more modern processes easy. These are both more useful in the field, due to not needing a shielding gas. Mig welding is the easiest process, if you get a mig welder, don't cheap out on a gasless, make sure you use a gas shielded process, though this isn't much use outside. Eventually you might like to tig weld for aluminium or stainless. Steer clear of 3-in-1 machines offering DC tig only. By the time you get to using tig you'll have realised scratch start tig isn't much fun and you'll want a pedal and a high frequency start AC/DC tig welder. In summary, learn with the welder you've got. Eventually buy yourself a ~250 amp mig welder, and eventually an AC/DC tig from a reputable brand. And small tip for your bro. Tack both sides before welding up one side fully as the heat of the weld will pull it out of square.

@patrickpigg4132

2 жыл бұрын

Sounds to me that you have never used flux core. Don't need no stinking gas.

@rusteh1234

2 жыл бұрын

@@patrickpigg4132 I've used flux core. And found the results inferior to gas 🤣. Each to their own of course. But especially for beginners, I think you'll get a better result with gas.

I can also find water With those, You guys ever tried with a stick that is formed like a y, u hold it horizontally and when u find water it forces it self down. Nice video

Grant you should get quick attach brackets for your cultivator , then you can just knock the shovels off with a hammer

Hi Grant I love your vid keep up the good work

Re: welding the f/c bracket. Tack both sides first before doing all that welding on one side. Also, don't use your hand on that clevis while hooking up. Use hitch pin or anything but your hand. Don't ask me how I know.

Most efficient way to reduce the stalk left on the surface is to get a chopping head for your combine. Then tillage will go much better. We use to have the exact same problem. Not anymore.

You need to invest in just a good old regular disk, and pull the disk over it once then come back with your field cultivator, your going to fight those piles all year long!!, also always try and run on an angle to the way your rows ran the year before it gives the implement time to clean out

We have one of the mulch finishers it real nice we run a ripper then disk then finisher leaves a really good seedbed

Quick fix for the valve stem, rubber valve stem and some grease or Vaseline and you can pop it in from the front of the rim. Done it a couple times on our 5100 John Deere

I've seen some people where I'm from bush hog there corn after harvest to try and mulch it up and from what I've seen bush hogging corn stalks seems to do a decent job in mulching up the corn and not leaving as much residue leaving a better seed bed

Nice video I’d say for future tillage I’d invest in a Vertical Tillage tool hope all goes well this spring

You should consider buying a chiselplow or a plow to work that residue in easier.

keep up the work

Just a tip on instead of sweeping your shop you can use a leaf blower and it works way faster and it cleans better than a broom

The Miller multimatic 220 is a solid machine and very versatile

Nice bead!

thats mamba jamba of yours is called a 1 inch gun PWERFUL impact gun. I use them on semi's, Tractors, every heavy peice of equipment

Don't ever not forget to wash/drain the fuel I went through burns from a situation similar to that and it hurts

I have the same 28 ft. cultivator. I put on 10 inch shovels. Removed like 17 shanks or so, if i remember it got 55 of so shanks. Better thrash flow /no plugging. You should of chiseled plowed it last Fall. That;s what i do. From the far SE corner of MN. I chop my stalks too, for continuous corn.

Miller matic is a really good welder. You get wire and stick AC and DC really nice welder

Good video boys

We use a lemken on the corn stubble and you have to really look to find a singe stalk

You can find shanks in Colfax at the the farm scrapyard

Don't know if you ever heard of them Grant but calmer is a company that had a problem a residue on their farm and they created a after market stock chopping roll for combine heads that you could look at too

On our old cultivator we welded a plate in the hitch and just drilled the hole out. Then just use it with the hammer strap on tractor

Maybe use a field rake??? Get most if not all of the old stalks and use your skidsteer to haul it away and burn it or something?

Ever thought of burning your corn residue off as a last resort? I’ve seen a free down here in south georgia but the fields off heat job keep the videos coming

A disk works well with chopping corn stocks then barring them. It is good to just flip the soil to let it dry out.

Rent a vertical tillage tool for corn on corn. Gotta chop that down much better

Its hard to cultivate in corn stalks anyway but i have had some pretty good luck with rolling baskets on the back of the cultivator it helps kinda too chop up everything.

No short cuts-it cost you in the long run- you guys are working and trying hard-great effort and sticking to it!

Run that welder on about 60-80 amps and run over that will 6011 rods the closer you are to the puddle the better off you are always watch the puddle

Use the pin to hold the hitch up on field cultivator or disk reduces the risk of crushing a finger or hand

I have a Cousin who does no till corn on corn every other year. the other years he plants soybeans also no till.

We mold board plow all our corn because it puts all the corn stubble under the ground it works in our area because we have a lot of tree cover and heavy muddy soil

Man this was a nice vid man 👍