Hey i live in the dominican republic and i have the 08 punto. I had this problem on Both back doors for more than 5 months and thanks to your video now there like New. Thanks a millón bro

@ricksyoutubechannel

7 жыл бұрын

kirasimo no problem dude glad it helps

@ricksyoutubechannel

6 жыл бұрын

Thank you so Much for Watching Please could you Help me out by Subscribing to My Channel it would mean a Lot to me . Thanks once again

Just picked up a Punto with the same fault. Back door jammed. Could not open the door (child lock was actived, so inside lever not working) until I watched your video showing the sharp tug on the door. Now door is open and I can effect this repair. Many thanks!

Thank you very much for the video! I followed your instructions and now my two doors open perfectly. I had put a similar will metal like you had previously on the handle. Thank you very much again!

@ricksyoutubechannel

7 жыл бұрын

thanks mate

@ricksyoutubechannel

6 жыл бұрын

Thank you so Much for Watching Please could you Help me out by Subscribing to My Channel it would mean a Lot to me . Thanks once again

Excellent video - worked like a treat. Only tricky stage was replacing the metal clip for window handle at end. I stuck a small piece of plastic (instead of metal strip in video) and this worked fine.

@ricksyoutubechannel

7 жыл бұрын

Thanks bud yeah can be a pain

@ricksyoutubechannel

6 жыл бұрын

Thank you so Much for Watching Please could you Help me out by Subscribing to My Channel it would mean a Lot to me . Thanks once again

Superb video. And superb DIY. I have a Fiat Linea. Will try this and keep you posted. Subscribed and liked. Thank you.

Top class just done this repair to my brother's car job done works to perfection , excellent video 👍👍👍👍😁

@ricksyoutubechannel

6 жыл бұрын

+john black thanks Dude

@ricksyoutubechannel

6 жыл бұрын

Thank you so Much for Watching Please could you Help me out by Subscribing to My Channel it would mean a Lot to me . Thanks once again

Great help!!! Thanks a lot

@ricksyoutubechannel

6 жыл бұрын

Please Can you Help the Channel out By Subscribing Thanks 👍

Brilliant video

Thanks save me hours of guessing

@ricksyoutubechannel

6 жыл бұрын

No worries please subscribe 👍

Thank you 🙂

Thank you

Hello,have a quest...can put 15 cm speakers? Or can put only 13?

Thank you very much for this video. Now I know what the issue is - wear on the (plastic) operating cam - I'll fix both my infuriating back doors! PS For anybody else with this problem, it's not a question of giving the mechanism 'more room' but less. (Since the contact point has lost material it needs that wear 'putting back' - hence the cable tie (or a shim of suitable thickness stuck to the appropriate surface). PPS It is possible (on my Punto) to open the doors when they're stuck - by pushing hard on the door just above and to the rear of the handle, and opening it just as you take the pressure off. Works 95% of the time for me. I'm guessing that the push takes part of the latching force off the latch, and so allows the worn cam to do its job - even though it's not applying its full design force due to the wear.

@michaelwarwick9930

3 жыл бұрын

I tackled one sticking door today - and glued a plastic shim to the top of the latch operating lever to eradicate most of the 2mm clearance between it and the handle's 'cam'. And...the door still wouldn't open. Ouch! (NB By 'cam' I mean the 'nodding donkey' lever on the outside half of the handle mechanism; the thing that activates a second nodding donkey lever on the inner half...that then pulls a short cable (about 100mm long) to open the door latch.) After a bit of investigation - with the reconfigured handle refitted - I realised that the reason the closed door wouldn't reopen from outside was that it wasn't really closed at all...so the handle wasn't properly operating the latch. The door felt closed, and looked closed, but wasn't. I'm talking 1 to 2 millimetres, by the way. Proof of this: I moved the door strike plate (a rectangular hoop on a backplate, screwed to the doorframe) 2 mil 'outboard' - and voila! - the door opened no problem! I then moved the DSP back again and the door wouldn't open. This explains why my 'pushing' fix works; the click I was hearing on pushing at the 'closed' door was the door actually closing fully. Ta-da! I therefore found that if I SLAMMED the door closed, it would reopen from outside every time; but if I just pushed it closed or closed it with a 'soft slam' - it would never. I'm not in the habit of slamming car doors, so I never previously realised that this was happening. (As an aside, these millimetres I'm talking about don't make the 'door open' warning light come on.) So... What I believe it comes down to is a combination of a) miniscule wear of (predominantly plastic) components, and b) the way the door latch mechanism is designed. It uses multiple 'uneven' levers (i.e. designed so that a very small movement somewhere creates a larger movement somewhere else - and vice versa. The problem with this is that without compensating for wear, tiny lever movements that are supposed to (always) magnify movement eventually stop doing so. Use (i.e. wear) causes slack to develop in every component of the door locking mechanism...and in the end one has to do something pretty drastic to compensate for (i.e. get rid of) all that slack in one fell swoop. In Rick's case someone had already glued a 3mm thick chunk of metal to the 2nd nodding donkey, but evidently it still wasn't enough; Rick had to add the cable tie (with curvature, another 3mm?) to get it to work. I had a 2mm gap between the nodding donkeys so I added 2mm of plastic shim and it didn't solve the problem. (I think the short handle-to-lock cable is a major weakness, because it's not a Bowden cable and isn't tensioned either.) To close, I got the door to open via a different fix...though ironically it left the door looking as though it wasn't latched closed - when in fact it was. I prefer Rick's solution, but if you can handle your door not looking perfectly shut, it'll save a lot of time. :-) Drop a line if you find an easier fix to this perennial Fiat Punto problem. I'll post this on the Fiat Forum too. And remember...don't be a Covidiot! Stay home. Protect the NHS. Save lives.

Thank you for your video! I follwed every step and the problem has been fixed! But another issue appeared... When I close the door now and press central locking the door will be locked properly but when press central unlocking button again the door is still locked. And the only way to open it is from inside. What could go wrong?

great video. But i wonder, could you not just remove the door card and super glue a metal block on top of that part, without taking anything else apart?

@sagecristian8144

2 жыл бұрын

instablaster.

@eoinf2773

2 жыл бұрын

Did you do that?

Hi. Would this procedure work for the front drivers door? On my punto I can open the door from outside when I press the central locking to unlock. But to shut the door I have to hold open the inside door handle and slam the door. So when leaving the car I have to get out the car. Walk to the passenger side. Climb in the car and lean across to close the drivers door. Would the process shown in this video fix that. Or do you think I have to buy a new door mechanism? Thanks.

Hi any idea how to fix an 08 punto door that stopped locking from the outside when all other doors are locked??

How did you do??

Hi would you know how to fix the boot mechanism of a fiat grando 07. I know where the emergency latch is but the actual electricals aren't allowing the boot to open. If you know anything to help me out! Already fixed the back door handle from this video and its super easy to follow! Many thanks!

@ricksyoutubechannel

6 жыл бұрын

Have not got a Clue Mate Sorry

Ma quindi con la fascetta di plastica si risolve?

This a great reference for how to get into the door and access the lock. However looking at the mechanism I'm not sure your fix is the best way to do it. I reckon the problem is that the cable from the handle mechanism to the latch is slightly too long so what I did was make up a small C-shaped piece of ~1mm steel wire and twisted the cable once through it to effectively shorten it. Works perfectly.

@Litesnip2022

4 жыл бұрын

Chris Alger I have same problem, it’s defo the cable that’s to long, what did you use to shorten the cable? I’ve tried a L shape piece of pipe it worked but it’s starting to play up again, just wondered what you bought to shorten the cable

@andreasvukman

4 жыл бұрын

@@Litesnip2022 If you want to do it properly you have to take out the whole door handle mechanism. On the part the author of this video left inside there is a screw that regulates the 'tightness' of the mechanism. You just have to tighten the screw clockwise and voilá, your problem is solved and back door opens normally from the outside. No dirty hacks. Obviously, many car mechanics would rather replace the whole door handle mechanism than to tighten a simple screw. Interestingly, even Fiat car mechanics don't know anything about this screw and they blame Fiat for the (Grande) Punto back door handle problem.

@PetrolKev

3 жыл бұрын

@@andreasvukman Hi. Where is this adjustment screw situated please?

may sound silly but could i super glue a peice onto thjat flat metal bit

@dragonenglish1014

3 жыл бұрын

No, just folow these instructions. I just did my back door today. I couldn't find a thick cable tie, but it worked with a thinner one. If your back door doesn't open, you cannot get it through the MOT. This video inspired my to try it myself. It took a while but I managed it and the door opens now. Just one cable tie.

Hi.. you from uk ?? I need fix that on my punto evo and replace windows regulators to on the rear.. can you do it i pay you !

@ricksyoutubechannel

6 жыл бұрын

vitor nosent yeah I'm from the uk

@vitornosent851

6 жыл бұрын

Ricks KZread Channel .. ok ! Can you fix 2 rear door handle and replace the window regulator???? Because i don't know how to do properly.. where you live ???

@dragonenglish1014

4 жыл бұрын

I think you can do this job by yourself, I have ordered two new regulators, You have to tape the windows in place.

bay japonice car and you will be happy?????

it works for my car but there is a problem. when i lock all the doors by key it doesnt open from outside. i have to open doors from inside first. if i open it from inside then it becomes able to open from outside allways until i lock the car by key again. i search it and someone says i put too much thick material over that plastic thing and i should use a thinner something. i will try it too.

@sicily98it84

4 жыл бұрын

Do you fixed It? I've same problem

@benny_bonomolo

2 жыл бұрын

@@sicily98it84 hai risolto? Ho lo stesso problema

@sicily98it84

2 жыл бұрын

@@benny_bonomolo no, ho perso le speranze, anzi, se trovi la soluzione....

@benny_bonomolo

2 жыл бұрын

@@sicily98it84 ho letto un commento che parlava di una vite da stringere... Proverò, se trovo la soluzione ti aggiorno

@benny_bonomolo

2 жыл бұрын

@@sicily98it84 il problema ti è successo dopo aver fatto la procedura del video?

Sorry mate, but your dirty hack is not necessary. If you want to do it properly you have to take out the whole door handle mechanism. On the part you left inside there is a screw that regulates the 'tightness' of the mechanism. You just have to tighten the screw clockwise and voilá, your problem is solved and back door opens normally from the outside. No dirty hacks. Obviously, many car mechanics would rather replace the whole door handle mechanism than to tighten a simple screw. Interestingly, even Fiat car mechanics don't know anything about this screw and they blame Fiat for the (Grande) Punto back door handle problem.

@micham2077

3 жыл бұрын

Where do you have this screws 😝

@j.c5657

3 жыл бұрын

Can you show how it's done? Or where the screw is?

Ma quanto sei moscio

@nicolaperruccio2592

5 жыл бұрын

Io non ho capito cosa ha fatto

Did not work

@ricksyoutubechannel

7 жыл бұрын

Can you tell me what you did ?