FCAW DIFFERENT WEAVING TECHNIQUE IN 3F FOR BEGINNERS 💡
Жүктеу.....
Пікірлер: 40
@heartfieldguitarcentral2822 ай бұрын
A few things from someone with 26 years of hood time. 1. turn your wrist so that you point the nozzle at the toes of the weld on each side. This will help prevent undercut on the edges and will also help to flatten out your weld profile. 2. Flatten out your weld profile. CWI's dont want to see humps and ridges. 3. the #2 circular and #4 triangle patterns won't fuse a seam if you were actually joining 2 pieces of steel together (instead of filling in the radius inside of angle) and going back down into on your weld will cause flux inclusions and x-ray failures. Use either #1 or #3, ideally pattern #3.
@lemuelramos5364
2 ай бұрын
Thank you
@seanmakesthings10 ай бұрын
great video 👍
@shiroly45709 ай бұрын
Exelent...very god...omedeto no japan...✌️✌️💪🤙
@darwintabares708511 ай бұрын
Very nice 👍👍👍
@sonwong1032 Жыл бұрын
Nice overhead welding 😮 mantap bossku 😎👍👍👍👍
@lemuelramos5364
Жыл бұрын
Thank you 😊 💓 ☺️
@seanmakesthings10 ай бұрын
it'd be great to hear what your finger is saying
@jaymarbartolome881 Жыл бұрын
Lupet idol !
@jaimebrito-vs3ey Жыл бұрын
Eu fico cada vez mais faciado.
@alexizvelasquez1107 ай бұрын
Master
@jaimebrito-vs3ey Жыл бұрын
Fico cada vez mais facinado dislumbrado com a soldagem bem executada
@lemuelramos5364
Жыл бұрын
Thank you so much 🎉
@chathurangalakmallakmal6252 Жыл бұрын
Supiri ❤❤
@lemuelramos5364
Жыл бұрын
Thank you 😊
@Spiderman208883 ай бұрын
😮😮😮😮
@QuanTran-xn1zd3 ай бұрын
Hàn 3F để diện thế nào bạn
@user-ic7dd8xg4cАй бұрын
2👍
@BinhhNguyenShin10 ай бұрын
Want to see your hand while welding
@ON7YT17 күн бұрын
23 v itu amper atau kecepatan kawat
@jericoloredo11403 ай бұрын
ano po kaya voltage at ampere nyan No 1 to 4
@manus57907 ай бұрын
No 2. and 4 best
@geralddumlao45658 ай бұрын
#3 yung gamit ko pero magkaiba tayo ng resulta.,.,siguro sa hand technique na lang yun at sa nakasanayan.,.,.,pero susubukan ko yung #4 baka mas mag-improve pa yung akin.,., 😅😅 👍👍👍👍
@lemuelramos5364
8 ай бұрын
Ayos yan idol
@MiguelAngel-qt2em
5 ай бұрын
Your video is very good, but it is important... to see how to weld just seeing how you draw, is not enough.😱❤️ You have to add this Filter... to your Camera❤ to record videos to improve viewing.👌😘 kzread.info/dash/bejne/q3mesJmCqL23iLA.html
@alanpanalangin72428 ай бұрын
xmas tree motion po ang d best s apat😁
@jaymarbartolome881 Жыл бұрын
Yan talaga diko makuha kuha idol, vertical hehe
@lemuelramos5364
Жыл бұрын
Madali lng yad idol,magpaturo ka kay jesusito galarce ung nag comment jan sa bba hehe
@jaymarbartolome881
Жыл бұрын
@@lemuelramos5364 hahahahaha inggit lang yan idol
@raulmarin87048 ай бұрын
estas mudo o que?
@alexizvelasquez110
7 ай бұрын
No habla español inteligente
@Bay0Wulf2 ай бұрын
I've seen a lot of welding tutorials that are BS on KZread but this one is puzzling. You’re welding the inside of an angle … which is to say you’re NOT welding anything … you’re just running fancy beads where penetration and quality means absolutely nothing. You should’ve set this up so you were welding the seams.
@jesusitogalarce8024 Жыл бұрын
kayo po b may ari ng company..?
@lemuelramos5364
Жыл бұрын
Bakit ingit ka hehehe
@lemuelramos5364
Жыл бұрын
Gumawa ka ng sau para may ambag ka 😅 at baka makatulong ka pa sa iba salamat
@jesusitogalarce8024
Жыл бұрын
kc ngsasayang k ng filler wire… pasalamat k mabait ang mga japanese.
@MiguelAngel-qt2em
5 ай бұрын
Your video is very good, but it is important... to see how to weld just seeing how you draw, is not enough.😱❤️ You have to add this Filter... to your Camera❤ to record videos to improve viewing.👌😘 kzread.info/dash/bejne/q3mesJmCqL23iLA.html
@helios23793 ай бұрын
that is some really bad welding... stop teaching people, you stay to much on your left and not enogh on your right and you never go in circles... you go left and right with a break on each side...
@kuntakentay69698 ай бұрын
but why weave flux core dual shield? youll just get slag inclusions. Suppose to just straight drag with very minimum movement just like stick. Im willing to bet none would pass xray
Пікірлер: 40
A few things from someone with 26 years of hood time. 1. turn your wrist so that you point the nozzle at the toes of the weld on each side. This will help prevent undercut on the edges and will also help to flatten out your weld profile. 2. Flatten out your weld profile. CWI's dont want to see humps and ridges. 3. the #2 circular and #4 triangle patterns won't fuse a seam if you were actually joining 2 pieces of steel together (instead of filling in the radius inside of angle) and going back down into on your weld will cause flux inclusions and x-ray failures. Use either #1 or #3, ideally pattern #3.
@lemuelramos5364
2 ай бұрын
Thank you
great video 👍
Exelent...very god...omedeto no japan...✌️✌️💪🤙
Very nice 👍👍👍
Nice overhead welding 😮 mantap bossku 😎👍👍👍👍
@lemuelramos5364
Жыл бұрын
Thank you 😊 💓 ☺️
it'd be great to hear what your finger is saying
Lupet idol !
Eu fico cada vez mais faciado.
Master
Fico cada vez mais facinado dislumbrado com a soldagem bem executada
@lemuelramos5364
Жыл бұрын
Thank you so much 🎉
Supiri ❤❤
@lemuelramos5364
Жыл бұрын
Thank you 😊
😮😮😮😮
Hàn 3F để diện thế nào bạn
2👍
Want to see your hand while welding
23 v itu amper atau kecepatan kawat
ano po kaya voltage at ampere nyan No 1 to 4
No 2. and 4 best
#3 yung gamit ko pero magkaiba tayo ng resulta.,.,siguro sa hand technique na lang yun at sa nakasanayan.,.,.,pero susubukan ko yung #4 baka mas mag-improve pa yung akin.,., 😅😅 👍👍👍👍
@lemuelramos5364
8 ай бұрын
Ayos yan idol
@MiguelAngel-qt2em
5 ай бұрын
Your video is very good, but it is important... to see how to weld just seeing how you draw, is not enough.😱❤️ You have to add this Filter... to your Camera❤ to record videos to improve viewing.👌😘 kzread.info/dash/bejne/q3mesJmCqL23iLA.html
xmas tree motion po ang d best s apat😁
Yan talaga diko makuha kuha idol, vertical hehe
@lemuelramos5364
Жыл бұрын
Madali lng yad idol,magpaturo ka kay jesusito galarce ung nag comment jan sa bba hehe
@jaymarbartolome881
Жыл бұрын
@@lemuelramos5364 hahahahaha inggit lang yan idol
estas mudo o que?
@alexizvelasquez110
7 ай бұрын
No habla español inteligente
I've seen a lot of welding tutorials that are BS on KZread but this one is puzzling. You’re welding the inside of an angle … which is to say you’re NOT welding anything … you’re just running fancy beads where penetration and quality means absolutely nothing. You should’ve set this up so you were welding the seams.
kayo po b may ari ng company..?
@lemuelramos5364
Жыл бұрын
Bakit ingit ka hehehe
@lemuelramos5364
Жыл бұрын
Gumawa ka ng sau para may ambag ka 😅 at baka makatulong ka pa sa iba salamat
@jesusitogalarce8024
Жыл бұрын
kc ngsasayang k ng filler wire… pasalamat k mabait ang mga japanese.
@MiguelAngel-qt2em
5 ай бұрын
Your video is very good, but it is important... to see how to weld just seeing how you draw, is not enough.😱❤️ You have to add this Filter... to your Camera❤ to record videos to improve viewing.👌😘 kzread.info/dash/bejne/q3mesJmCqL23iLA.html
that is some really bad welding... stop teaching people, you stay to much on your left and not enogh on your right and you never go in circles... you go left and right with a break on each side...
but why weave flux core dual shield? youll just get slag inclusions. Suppose to just straight drag with very minimum movement just like stick. Im willing to bet none would pass xray