“We’re welding a fucking dumpster…” no truer words ever spoken. People get SO worked up about weld quality and perfection… no matter how good you weld that, you’ll probably be out there next week fixing it again anyway lol. These guys at these scrap yards are fucking brutal on equipment.

@kevobrando95lx44

2 жыл бұрын

I work at a shop where we produce roll offs and 2+ yarders for commercial use, for concrete and metal use you want some good welds. Those things are abused so you wanna put some care into it.

Look forward to the video of fixing the magnet bracket. Will be really interesting!

@MeltinMetalAnthony

2 жыл бұрын

You and me both!

@thomasmeschia

2 жыл бұрын

Could flip the brakets over with holes towards the center, giving fresh material to magdrill ?

@thomasmeschia

2 жыл бұрын

Oh I'm wrong they'll be shortened after torch cut

Your descaler peens the surface so under each little impact metal gets compressed and expands a little. Remember what the head of your cold chisel looks like. All these little expanded areas push against each other so you have a thin outer layer in compression on the peened surface. Since failure cracks can result from tension in that outer layer, the compression stress negates a bit of the tension stress and the parts act stronger. Peening under controlled procedures is common aircraft practice. I enjoy your videos.

So good to see all these different projects. Learn a ton every time.

As always the content is absolutely golden. I’m just getting started in my welding career but I’m hoping to be doing this type of work some day soon.

Great video. Thanks for including details - very educational. I always learn something practical from your videos.

4:10 peening will work harden that lever, but slow cooling after heat & bend will return that part to it's original properties. It's likely a low carbon steel, so very few options for hardening.

Just a handy tip when you want the c- channel to come down use a 6inch c clamp with 2.5 inches cut off or half with a heavy duty base plate and clamp it down in place it comes in handy even in small repairs it's a life saver

Good job. Informative. Especially when you talked about cracks developing from torch cut holes. Keep it up.

Appearance is gold I don't weld with my finger nor cheater the customer deserves better,

The cracks on the magnet look like a design change would help. Change the angle of the bars so they are not so flat. No doubt torch cutting the holes didn't help but looks to me like they need a little more meat on the bottom if room allows it.

@oscarborjon6112

2 жыл бұрын

He said they shouldn’t had cut the holes with a torch. You can cut out those holes with a torch. He just wants to use mag drill. He could’ve welded those crack and put a plate on both sides like a sandwich.

@WowenandWilma

2 жыл бұрын

@@oscarborjon6112 brother do you see theres no room for "plates on both sides".

@Jcreek201

2 жыл бұрын

@@oscarborjon6112 He's not wrong, the ridges from the torch cut do create stress risers. But he could have easily welded it and cleaned up the bore with a flap drum to alleviate 90% of that issue. Not worth replacing all those arms over. The OP is right though, the design puts completely unnecessary flexural stress on those arms.

I really enjoyed this longer video Andrew !

Places like that are the bread and butter of the job. Nice work as always

Nice work Anthony! When you welded the backside of that angle/ channel I was thinking how throughly was your work even on a dumpster! Probably stronger now than from the factory. Great Video!

Great video, very interesting. Looking forward to the repair video on the electro magnet.

Another great video Anthony!!

Fantastic video all ways look forward to seeing them. What a days job those cracks are made to think that could of completely broke. Hope you get to make a new 1 and can film it. Keep up the great work 👍👍

@MeltinMetalAnthony

2 жыл бұрын

me too!

We’re welding a dumpster this isn’t a fucking space shuttle 😂😂😂. Love it.

One of my first welding jobs was at a scrap yard like this one repairing the bins and the escavators.

I run a little welding truck and I too weld On just about everything….. These people’s comments are entertaining…. I didn’t realize there are so many keyboard/ welding experts!!!! GOOD LOOKIN SOLID WORK👍👍👍👍

@MeltinMetalAnthony

Жыл бұрын

Honestly I’m getting to the point where I don’t read them. This is the first time in a week or so I have

Hey Mel, just hooked in to your videos. Great talk through, nice commentary. Smart move, pushing that mag repair, just like in the China shop, “You touch it, You own it”, in other words if it breaks after your repair, they’re coming to see you. Hood down lights on.

Need to get you a dog and a wedge for that, we’ve used them a ton and man do they ever work good! Good content as always!

Your a one man army Love it bro Keep it up 💪

From one business owner to the next. I'm planning a trip to Florida in August for vacation. Wouldn't mind if you didn't to tag along a job or two. Free labor and yea I love work so much couldnt think of anything else better to do with my vacation time. 😆 🤣 😂 Keep up the hard work you continue to be a inspiration to others.

I use a needle scaler to peen welds in cast to compress weld and prevent cracks.

Watching that bead from the front while you worked the back was killa, the red glow cruising along

I'm new to your channel and it looks like you have a wealth of support . Very interesting looking forward to watching.

@MeltinMetalAnthony

2 жыл бұрын

Welcome aboard!

That was a slick move keeping the arc from tack to tack on that can..

@MeltinMetalAnthony

2 жыл бұрын

I figured I’d show case that. As long as no one does it on pipe or structural lmao

@imacaryay7628

2 жыл бұрын

I'm in welding school atm, definitely going to try that

dear GOD man!! can none of ur 1000 sponsors throw you a pancake hood?! today woulda been the proper day🤙🏽

Bro I've been doing repair work for quite awhile sixty plus years and believe me i have learned alot from your videos just goes to show you that your never to old to learn some things.keep up the good work

@craigclemson9642

Жыл бұрын

If you learned anything from this guy and you have been at repair work sixty years retire

Looks like your making good use of that new air compressor…why not?? Another tool in the arsenal!!! Keep stacking my guy!!!

It would take a while but you could mag drill bigger holes and press a sleeve into the steel the right size for the pins. I know it’s still a heat affected zone but I think that would probably be a decent cheaper option. You could even just press a sleeve and weld it and grind it smooth and I think that would do fine as well. Because once you press the sleeve in and welded it you could air arc those cracks out and full pen weld them using the sleeve as the start of your root pass.

@MeltinMetalAnthony

2 жыл бұрын

Gotta know your customers and I know this customer wants fast and cheap

You da man I’m definitely looking forward to seeing that magnet fix as well hell ya Wooooooo

Great video Anthony mate! Jealous of the weather you're working in! Peace from shitty England 🇬🇧 🇺🇸

Did you consider drilling larger holes and then welding inserts in? Seems like that is the most cost effective solution to me.

Another great welding vid. Right on

@MeltinMetalAnthony

2 жыл бұрын

Glad you enjoyed it

"this is dumpster, this isn't the space shuttle", nice line.

Get you some short pieces of 1x1/2” and 1-1/2x1/2” channel iron to lay on round stock when trying to C-clamp it. Helps quite a bit.

You need one of those hydraulic kits that has a hand pump, there kind of fast in some cases have a few adaptors for length or wedges and plates for pulling or pushing - toys in the toy box.

Dang was looking forward to that project. Oh well next video should be nice as always

Dude I used to work for that company that made that magnet pretty neat seeing it in a video

Great work man! For the glare problem you were having, I just self tapped a big square piece of canvas on the top of my hood to run down the back of my head and neck. You can just cut up an old welding shirt.

@MeltinMetalAnthony

2 жыл бұрын

I was out of tape 😢 but great idea on a old welding shirt! I was using a rag

@JohnWheels

2 жыл бұрын

@@MeltinMetalAnthony Thanks! I actually used self tapping screws but I actually like the tape idea better cause it's removable.

@alexjeremiah8915

2 жыл бұрын

That's what we do in the factory I work for. Cut up a weld jacket or some scrap vinyl and tape it to your hood.

Nice stick welds! Really nice beads!:)-John in Texas

From what I'm looking at just cut them loose flip them over and drill the hole in the other end as well into the inside center and weld up the holes and welded back together and use your expensive mag drill

On that little dumpster , for the crack that would not close .. i used to be a structural iron worker , connector , and we used to carry some big J adjustable Clamps and we would cut off the bottom piece that acts as a plate to grasp what ever your trying to hold and we would weld the j clamp down that allowed us to have direct over head pressure to push down on a pc and not have it twist

With the channel bent up on that Can, you think you would’ve been able to tack up a plate on the can itself and use it as a base to use a bottle Jack to push that channel back down? Genuinely curious always trying to learn! Love the videos man!

Im just curious, how in the hell did you aquire your cert of completion to be a Jman welder

Been there. Relief cut then pull down and fill in on the C channel.

Cool video Anthony

Great video;)

How are you liking gouging on your machine? I’ve got a 325 trailblazer and would like to gouge but don’t want to over do it with the machine

Nice job man. Time for a remote, they really save trips back and forth to the welder. Especially jumping back and forth from 6010 to 7018 or different sized rods etc.. I know you know that but just tossing it out there. ;) I've been running my Crosslink remote for about a year now....don't know I got along without it.

@MeltinMetalAnthony

2 жыл бұрын

no doubt, I want the trailblazer 325 airpark when it comes out with wireless remote

@freebirdwelds

2 жыл бұрын

@@MeltinMetalAnthony I'm too old to drop that kind of coin on a welder. lol

Need to hook your self up with one of those Pipe Liner Pancake Hoods, form what I understand they designed to Eliminate that Back Light/Glare with that kinda Ski-Mask Goggle Setup. As we'll as being Compact and Light Weight. Would be a handy dandy accessories to have in the Tool Arsenal ?

Look into getting a pancake hood. It eliminates glare. Pipeliners use them for that reason.

@MeltinMetalAnthony

2 жыл бұрын

good suggestion

man, if i had to do those repair id ask for the fork lift so i could lift those containers and work standing XD

Love the content dude! Keep up the awesome work! How do you like the Hobart helmet?

@MeltinMetalAnthony

2 жыл бұрын

works good

Why not use some screw dogs or grasshoppers to pull/push stuff back into place? Like when you trying to get the "F"/ bessy clamp on it. A c clamp cut in 2 or simple a couple long bolts,"L" plate and couple nuts to make a nice screw dog or grasshopper would've worked good. Just an idea

I'm surprised to see you not weld around the edges on the first weld you did where you were selling a pieces of metal flat to another. In my experience that going to hold water inbetween those two pieces causing it to rust and rot much quicker. If I do a weld like that I always weld around sealing the inside where it's sandwiched together

@CB-sd6kl

2 жыл бұрын

It was just a tab to hold the handle in place. There’s no where to weld on the edges

Great work as always. You should pickup a Miller or Lincoln “face mask” and keep it on your truck. They are invaluable for work outside. Not only do you have no backlight (since they are goggles) but you can get your head in places/better visibility than a normal hood.

@MeltinMetalAnthony

2 жыл бұрын

Might have to add that to the tool collection!

On the magnet - all you had to do was cut them off and reverse them then mag-drill the holes. Welding up the cracks would be good but they would bend close. Just my 2 cents

Have you tried a pancake shield Anthony? Dose good to eliminate sun glare.

If they don’t wanna remake the arms, will you be welding it up to get them going again?

You need to invest in a pancake welding Helmet ... You will find out it's heaven when dealing keeping sun out...

Soon as I seen them cracks my brain went Cha-Ching $$$ lol

Did you ever end up getting to fix that in the end? That would have been or would dope too watch you fabricate that.

You could try s dog and a wedge or screw dog to pull that C channel down basically a dog is just a piece of steel like plate any thickness with a notch cut out of it for your wedge you weld the 1 side down and smack your wedge in between the notch and C channel

Only thing I would suggest on cracks is drilling out the ends of them because it stops the crack

gota love those needle guns.

I would almost second guess those even being cracks. Id bet its the entry wound from the torch. See it everywhere on new, cnc cut thick material

you gotta be drilling holes at the end of the cracks it stops the crack from becoming bigger, it basically routes the crack back to itself.

The Magnets I have seen here in California have chain instead of a bracket that can crack.

can't wait till you get back on the magnet.....cheers

This isnt the space shuttle, how true!

If ridges are not too deep they can be smoothed out with an end grinder.

Mud dobbing lmao 🤣

How are you pricing jobs? Time, scale, piece work?

The cracks actually look like starter cuts for the holes

@MeltinMetalAnthony

2 жыл бұрын

they are forsure cracks

@tobiasbaker-rainford4000

Жыл бұрын

Pretty sure those are lead in cuts

How did you terminate the crack on the dumpster at 5:00? Or did you?

When welding on multiple pieces of equipment at the same place do you charge by the hour or a minimum per piece of equipment

@batsonelectronics

2 жыл бұрын

based on other videos, I think he charges 100-120 /hr so I would think some minimum show up fee and whatever the hourly time is. Hopefully he responds and is more specific. peace.

Yes thats a good days work

Are you still moving to Montana?

lol why arent they using the D-rings and chains that the magnets usually come with?

@MeltinMetalAnthony

2 жыл бұрын

they pick it up with the "tongs" can't do that with a chain

Should just flip that crack towards inside and weld the cracked hole on the magnet project just to save money 👍

Could you flip bars over an then drill

Did you go back to fix that magnet?

MM77 Approved 👍🏼👍🏼

"Today on episode 1 of Weldin' Wyatt's Winkle..."

We use chain on our magnet

You can torch cut it 100% I do it only buildings, you just need to clean it up so there is no tear points

What kind of scrap yard is this? As soon as you said "buy some metal" they should have said "Hell, we got mountains of the stuff. I'll have some guys scrounge you up something." I get it strictly speaking it is better to use new, store bought metal with a pedigree other than mystery meat bastard metal. There is a big scrap yard (sorry Metal Recycling Center) in my town and it seems the whole place is held together with mystery meat bastard metal. BTW I just found your channel and I love it. Thumbed up, subscribbled and all that stuff in the dibbly do. Guys like you burning rods, heating with torches and beating with hammers keep industry going. I also respect the hell out of scrap yard workers. They do more for the environment than Prius drivers.

Is there a vid of you fixing this?

@MeltinMetalAnthony

Жыл бұрын

Didn’t get the bid but after I moved heard they had it fixed elsewhere and it is cracked again

Clever way to bend the latch back

Whats the cost for the whole job but specifically the magnet?

Well. I learned thst you shouldn’t torch cut a hole like that in a structure piece thst is gonna be a long term use piece. Good to know. I also wonder if because of the torch cut, the location of the crack is showing on the bottom ones of the hole, with the least amount of structural metal leftover, ultimately failed from stress and over use.🧐

@MeltinMetalAnthony

2 жыл бұрын

100%

Needle scaler new addition to the toolset or do you rarely use it?

@MeltinMetalAnthony

2 жыл бұрын

ive had it, didn't have the air

Grab a port-a-power kit they make decent cheap sets

Just make a new lift point for the magnet lol that thing looks dangerous

@MeltinMetalAnthony

2 жыл бұрын

They don’t wanna spend that kind of money unfortunately 🤷‍♂️

@jonhy2x4

2 жыл бұрын

Sad 🥺 penny wise, pound dumb.

don't let em fool ya those scrap metal guys are loaded fix it right👊👍

110 amps on what I'm assuming is 1/8th 7018, and then 75 amps on 3/32nd? I'm a welding novice, why are you using such low amperages? In class we use 125 amps on 1/8th rod and 90 for 3/32nd.

I’m not a welder lol but I do have experience lol