Building a dual round bale hay spear so I can cut time/fuel in half when putting up hay,
Жүктеу.....
Пікірлер: 28
@kevinashby37842 жыл бұрын
Looks real good.
@knarftrakiul3881 Жыл бұрын
More people need to get into making their own tools... welding is mentally easy to learn but can be hard doing the physical, dealing with heat, sparks, etc... Get good at welding then making your tools is easy
@CenTexAg
Жыл бұрын
100% agree!!
@sherrywilliams17924 жыл бұрын
admire your adility to run a torch close to the vehicles....I would need water on the floor and fire ex. close...i'm a worry wart...
@CenTexAg
4 жыл бұрын
Haha I think I’m getting alittle to complacent. Plus the battery was dead on the impala.
@JH_HAY3 жыл бұрын
Nice
@Rdrake14134 жыл бұрын
Nice job. I would have run a couple of pieces 3x3 tubing off your center tubing like an A frame for a little more support.
@CenTexAg
4 жыл бұрын
If I see any kind of flex I may do that
@Rdrake1413
4 жыл бұрын
@@CenTexAg Yeah don't know how much weight the tubing will take or how much your bales weight. But if it flexes it will help.
@Rdrake1413
4 жыл бұрын
@@CenTexAg I was thinking 2x2 tubing would work for the support braces and would be a little cheaper. And I think it would look better.
@ricksanchez74594 жыл бұрын
I tried the bigger/longer spears, but we had trouble on tight bales. Let us know how they work for you. Ive polished and sharpened it up but it still tough to qork with. We ordered an HLA dual short/thin spear for $600, I hope it works better. Not many honest implement reviews on youtube.
@CenTexAg
4 жыл бұрын
Will do. Thanks for sharing your experience
@skylerballman731419 күн бұрын
How long is your 3x3 square tubing were your bale spears are on? And how do you know we’re to put your bottom brackets to hook up to your bottom 3 point arms?
@danielliford8809 Жыл бұрын
So did u come off 4 inches from the outside and put your first spear then set the next one to 20 inches and did the same for the other side? I’m looking to build one almost like this set up. Great content.
@CenTexAg
Жыл бұрын
Yep exactly
@fishguts42474 жыл бұрын
That's a monster of a spear. like the rag top 65 too. Is it a SS by chance?
@CenTexAg
4 жыл бұрын
One year off, it’s a 66. No it’s just a regular convertible that came with a 283
@ericbrendle25513 жыл бұрын
How tall is the top link riser tubing? Liking the vids too!
@CenTexAg
3 жыл бұрын
It is 24 inches
@dustinrogers57352 жыл бұрын
I am about to build one of these. Have one very similar pictured in my mind. So 24” tall and 80” wide right? Anything you’d do different? Work well?
@CenTexAg
2 жыл бұрын
Yes on the measurements. I wouldn’t change anything because it works really well.
@dustinrogers5735
2 жыл бұрын
Ok thanks for the info and the video!
@dillonmcnece6004 жыл бұрын
What’s the length of the 3x3 tubing that the spears are mounted too?
@CenTexAg
4 жыл бұрын
80”
@jeff59792 жыл бұрын
i would like to have something similar to haul 3 rolls, 2 on bottom 1 in middle top. I have 4x5 probably no more than 1200lbs each, could this set up carry three?
@CenTexAg
2 жыл бұрын
Yep I tried that. But I was to scared the top bale was going to come threw the back glass. You would need to add a riser from the top link up to prevent that from a happening.
Пікірлер: 28
Looks real good.
More people need to get into making their own tools... welding is mentally easy to learn but can be hard doing the physical, dealing with heat, sparks, etc... Get good at welding then making your tools is easy
@CenTexAg
Жыл бұрын
100% agree!!
admire your adility to run a torch close to the vehicles....I would need water on the floor and fire ex. close...i'm a worry wart...
@CenTexAg
4 жыл бұрын
Haha I think I’m getting alittle to complacent. Plus the battery was dead on the impala.
Nice
Nice job. I would have run a couple of pieces 3x3 tubing off your center tubing like an A frame for a little more support.
@CenTexAg
4 жыл бұрын
If I see any kind of flex I may do that
@Rdrake1413
4 жыл бұрын
@@CenTexAg Yeah don't know how much weight the tubing will take or how much your bales weight. But if it flexes it will help.
@Rdrake1413
4 жыл бұрын
@@CenTexAg I was thinking 2x2 tubing would work for the support braces and would be a little cheaper. And I think it would look better.
I tried the bigger/longer spears, but we had trouble on tight bales. Let us know how they work for you. Ive polished and sharpened it up but it still tough to qork with. We ordered an HLA dual short/thin spear for $600, I hope it works better. Not many honest implement reviews on youtube.
@CenTexAg
4 жыл бұрын
Will do. Thanks for sharing your experience
How long is your 3x3 square tubing were your bale spears are on? And how do you know we’re to put your bottom brackets to hook up to your bottom 3 point arms?
So did u come off 4 inches from the outside and put your first spear then set the next one to 20 inches and did the same for the other side? I’m looking to build one almost like this set up. Great content.
@CenTexAg
Жыл бұрын
Yep exactly
That's a monster of a spear. like the rag top 65 too. Is it a SS by chance?
@CenTexAg
4 жыл бұрын
One year off, it’s a 66. No it’s just a regular convertible that came with a 283
How tall is the top link riser tubing? Liking the vids too!
@CenTexAg
3 жыл бұрын
It is 24 inches
I am about to build one of these. Have one very similar pictured in my mind. So 24” tall and 80” wide right? Anything you’d do different? Work well?
@CenTexAg
2 жыл бұрын
Yes on the measurements. I wouldn’t change anything because it works really well.
@dustinrogers5735
2 жыл бұрын
Ok thanks for the info and the video!
What’s the length of the 3x3 tubing that the spears are mounted too?
@CenTexAg
4 жыл бұрын
80”
i would like to have something similar to haul 3 rolls, 2 on bottom 1 in middle top. I have 4x5 probably no more than 1200lbs each, could this set up carry three?
@CenTexAg
2 жыл бұрын
Yep I tried that. But I was to scared the top bale was going to come threw the back glass. You would need to add a riser from the top link up to prevent that from a happening.