Brilliantly done.

Excellent training film.

Very Educational 😊

I'm nearing the end of my ACS and this video is very hjelpful.

@BoilerrepairNet

Жыл бұрын

Hi Danny check this out. The Boiler Repair Library - a fantastic tool for you to increase your technical knowledge in gas and electric boiler repairs - is now only £5.00 one off payment for Lifetime Access! That’s Lifetime Access to hundreds of How-To and Overview videos, updated every month. If you are currently paying £10.00 per month you can cancel your membership and rejoin for the £5.00 Lifetime Access membership instead. Click here to view screenshots of the Boiler Repair Library before you join: arboilers.kartra.com/page/BoilerRepairLibrarySpecialOffer

Hi I have a reading of 62 ohms? Does this mean the gas valve needs replacing? Or is it still a PCB issue?

How long does the boiler fire for up for in heating mode ?

What about the pressure?

Thank you for your comments and can you please subscribe to our channel

For good part did not see the mains cable stuck underneath the mother board.

Boiler radiators won't go hot I've tried everything it's a valient eco

Does the new replacement PCB need setting up at all? I’ve read it could result in a F70 code which means it needs associating with the particular boiler model it’s installed into?

@BoilerrepairNet

Жыл бұрын

99% of the time you don't need to set anything up. Also could you subscribe to our channel

So you make sure the knobs hot water and heating are on full a on the pcb ?

@BoilerrepairNet

Жыл бұрын

Yeah 👍 Also can you subscribe to our channel 🙏

Great video :) we have the same problem on our ecoTec pro 28, had f61 in the past but now seems to settle on f62, we can clear the code an resume normal operation but we also see temp fluctuations on the display (actual water temp is fine). Everything points to PCB as you video suggests, but as we don’t know the age of the boiler we are debating just getting a whole new unit (maybe different brand). Would your advice be to invest in a new boiler or just replace PCB? If PCB what’s would be a fair price for parts and instillation? Thanks for your video an time :)

@BoilerrepairNet

2 жыл бұрын

We have replaced many pcbs on your type boiler and it should run for many years. We would charge 150 labour plus 187.00 for pcb plus vat. The pcb covered for 12 months. What area are you in?

@ImranKhan-hz8jy

9 ай бұрын

Do we not have to put any code into after replacment??

How to measure inlet working pressure at appliance in this boiler? Is it by taking the side panel out???

@BoilerrepairNet

Жыл бұрын

No you need a small ratchet tool to get in gas valve inlet test point and you will need to remove the air pipe

@BoilerrepairNet

Жыл бұрын

Also check out this out www.onlineboilerrepairtraining.co.uk/

Gr8

Mate i have same issue f.61 code but, its intermittent, i powered off and reignited boiler and it works fine but i may get this code again after couple of weeks so what is the issue?

@BoilerrepairNet

Жыл бұрын

It's normally the pcb or it could the gas value. Also could you subscribe to our channel 😊

@sukisingh7268

Жыл бұрын

Bur what if it continually works fine for months on end as it has so far by just pressing reset button?

@BoilerrepairNet

Жыл бұрын

@@sukisingh7268 just run with it and see how it goes

@sukisingh7268

Жыл бұрын

@@BoilerrepairNet its getting worse esp. Night time it cuts out we keep resetting

@StuHNomadBiker

Жыл бұрын

​@@sukisingh7268 Get an engineer out to it !! Stop fishing for free advice so you can try and fix it yourself ... pay for somebody who knows what they're doing ..

Thank you for your comments and can you please subscribe to our channel please

He said it was the gas valve cos that what it says in the book .. lol... see so many lads do it, can't always trust the book.... experienced lads know that there are other reasons many times that throw out the same fault... its all about learning and experience.

@BoilerrepairNet

Жыл бұрын

Thank you for your comments and can you please subscribe to our channel 😊

I just kept my finger on the reset button for few seconds and code went away and works fine now.???

@BoilerrepairNet

2 жыл бұрын

Ok that's great 👍

@infiniteloopslawson5301

2 жыл бұрын

@@BoilerrepairNet it's done it before could it be a faulty sensor?

@BoilerrepairNet

2 жыл бұрын

@@infiniteloopslawson5301 it's normally a gas valve or PCB fault

@okafka5446

2 жыл бұрын

@@BoilerrepairNet Got exactly the same problem (F61, with temperature jumping around when you reset) thanks for your clear video. Been told it's either the PCB OR a faulty gas valve, and that these boilers (we have the Vaillant ecoTEC plus 837 now 12 years old) have built in obsolescence, so we might as well replace the whole boiler. Not sure if this isn't upselling, but out of interest, once the pcb is replaced is the boiler good to go for a couple more years as long as regularly serviced?

@BoilerrepairNet

2 жыл бұрын

@@okafka5446 100% yeah

careful when two wires the same colour - label with a bit of tape before you take a photo

F61, constant cutting out

@BoilerrepairNet

Жыл бұрын

Possible gas valve or PCB

@BoilerrepairNet

Жыл бұрын

Also could you subscribe to our channel 😊