That old iron running gave me goosebumps. She sounds beautiful.
@pappy451
5 күн бұрын
me too ! loved it !
@Walkercolt121 сағат бұрын
One of my Antique Cycle buds has a 1913 Harley-Davidson (First H-D) ALKY (pure methanol) burning board-track racer! One speed, no brakes, no throttle, a kill switch that cuts the magneto for "speed control". 119 MPH Laps on the 3/8th mile dirt track at the Creek County Fairgrounds on BICYCLE TYRES pumped-up to 90 PSI (white Firestone's). Total loss lubrication of 50 weight CASTER BEAN oil. Every 5-6th lap, reach between your legs and manual pump the oil pump until it smokes a puff. Think about Glenn Curtis-he bought his frames from brothers in the bicycle trade near Dayton, OH and put his engines on WRIGHT BROS. frames. Now put down an 1/8th mile track of boards, put 40 riders who kicked, punched, spit on each other on a 25 foot wide track at 110+ MPH. It was called "Murderdrome" rather than Motodrome. Many of them became WWI Aviators. I'm working on a street 1916 "ACE" 52* (Bosch Magneto) Vee-twin 1065 cc three speed tranny. Acetylene headlight and all! By 1925, there were at least THREE street motorcycle manufacturers for each letter of the alphabet. EXAMPLE: A: Ace, American Flyer, American Eagle, American Flag, Ace-Hi, All-Bee, A-EZE and 12 more. The "Panic of 1922" killed most brands along with the Model T. When dirt roads turned to mud-pits, an automobile had some advantages. In 1925 there were about 10,000 miles of paved ('improved" that could mean gravel) "highways".
@NitroModelsAndComics18 күн бұрын
Seeing that thing light and then those flames. The tone is perfection.
@rocker4144 Жыл бұрын
Such a beautiful piece of motorsport history. it's so cool to see an old dog spit flames again!
@HarmonRAB-hp4nk
15 күн бұрын
dad sold my bike... I was named after a 1951 panhead... running all those years :-)
@spaceflight10193 күн бұрын
Forget putting this on a bike, it needs to be powering a go-kart! I can close my eyes and hear that song behind me as me and my kart break out from under the tree canopy and head into the open country on the IOM Mountain Course.
@pastorbobncc36511 күн бұрын
Absolutely loved coming along for the build, have a blessed week my friend.
@scarecrow800419 күн бұрын
Ah the good old days when motors made a small enough amount of horsepower that you could drill holes in the connecting rods to reduce reciprocating weight. Absolutely fascinating. Loved the shaker twin video at the end, hold on tight or it'll be down the street by itself ... it craves to motivate.
@FLORIDAMANIAM-he2lz
19 күн бұрын
Or you could just weigh and balance them
@AS-bt4xp11 күн бұрын
Housing covers, cylinders, flanges etc. have to be tight crosswise in any case, otherwise internal tensions and leaking follows! A good educated and teached mechanic has to know that!! Greetings from Germany!
@larsblankenfjell981415 күн бұрын
Best I seen for a very long time, really Love this engine!!!
@MrStratbatАй бұрын
Great video..Thanks for no music and thanks for running the engine...Great job...
@tnekkc17 күн бұрын
My father had an old '74 when he was in high school in 1939, He was caught doing donuts in the parking lot, and had to eat his lunch in the office.
@dntlss
8 күн бұрын
And he didnt come back and kill the principal the next day,lol, he knew he was caught and took it like a adult unlike today.
@davenorgrove3193 Жыл бұрын
Nice! Thanks for putting this together!
@seanmakesthings9 күн бұрын
So rad to see the old engineering of this motor like the screw in cam bushings/bearings in the case, what a trip. Thanks for showing us behind the scenes
@dntlss
8 күн бұрын
Any particular reason why in the beginning and most of the video hes not using any oil or grease or assembly lube or anything like that? sorry to ask you but seems like he doesn't answer comments.
@seanmakesthings
7 күн бұрын
@@dntlss You know, I really couldn't tell you for certain, but I'll try to make an educated guess here for you. I'd probably guess that assembly lube wasn't too common back in 1928, so using it today is kinda moot. I also believe that this particular engine gets its oil from a hand pump, so I don't know how important assembly lube is gonna be in preventing wear and tear when the engine itself doesn't have a constant circulating oil supply. You could lube the thing up, but it's probably not gonna stay lubed for long, and the oil that needs to get into oil passages and specific crevices might be blocked by gooey assembly lube. One other thing you might research was that in 1929 they introduced a throttle-controlled oil pump, which i have no context for, other than the names and an old article claiming that the throttle-controlled oil pump increased the oiling efficiency and overall health of the engine by a ton. So there ya go, hope my guesses might shine some light on the reasoning behind him not lubing it up like you would a 50s/60s/70s engine found in cars
@seanmakesthings
7 күн бұрын
@@dntlss Read my other guesses first, but here's an alternate theory: he assembled the entire motor for clearance purposes, tore it down off camera, lubed everything perfectly and reassembled it for the final part of the video where he fires it up. Not really sure.
@cameronlilly48144 күн бұрын
Interesting watching this after Keenan Tatro's videos; despite the difference in time period this still looks like the work of Harley Davidson when compared to later twins.
@user-ks5vm8ht7v20 күн бұрын
WOW !!! Super sound ❤❤❤❤❤ Thank YOU!
@MonteFleming Жыл бұрын
I just wanted to say thank you for the video on how to access the subharmonic register. Singing basso profundo is freaking fun.
@gnm10918 сағат бұрын
Very nice work!
@evanreese4883 Жыл бұрын
Wow, the bass tones out of that thing! Sounds like a combination of fart bass and lip buzz. Now I just need to hear a beat over it.
@bmwtravel110020 күн бұрын
if you need parts for it, check with Reiman Harley Davidson in Kewanee, Illinois. Old Hank Reiman (not his son Roger) was an ace Harley tuner way way back.
@FelipeMaldonado-wk4ne23 күн бұрын
Great job. Very good video.
@stevenleek125421 күн бұрын
Beautiful!
@PPGDC19 күн бұрын
Beautiful!!
@jaynedoe195921 күн бұрын
That was really fun!
@Zulutime4412 күн бұрын
What a beautiful exhaust sound. You know its a Harley.
@psk5746
11 күн бұрын
Yeah because they all sound like shit
@choppergirl24 күн бұрын
You don't ever want it to stall out and quit, that will leave you stranded by the road. Maybe set your idle screw higher. Not about the sound, or even about the hp (well, if it was used for racing, then it is), it's about getting you there and back without issue or headaches.
@redtobertshateshandles
22 күн бұрын
An old race tuner I worked with often the first thing he'd do was turn up the idle. And on a race two stroke turn it right off.
@choppergirl
22 күн бұрын
@@redtobertshateshandles hard enough to keep an old engine running as it is. once you get it started you don't want it conking out on you all the time. it really swcks if your battery is dead, you have to kickstart or push start it again, or... your compression release is broken. I deal with all three all the time on the farm with this old junk.
@johnarnold893
15 күн бұрын
@@choppergirl Battery, hah, what battery. It's a race engine and uses a mag for spark.
@choppergirl
15 күн бұрын
@@johnarnold893 Fair enough, but a dead battery is huge concern on my bikes that are too heavy to push start and jump on. It will leave you stranded and phwcked. I can push start light cars on flat paved ground and jump in the seat and throw them into 2nd and start them (done that more times than I want to count), but pushing a heavy motorcycle to a running start and swinging a leg over and kicking it in gear without dropping it is beyond my stamina and skill level. Don't want no kickstart motorcycle ever again, you'll wear out your leg or break it trying to get that thing started.
@zorianwilson8523 Жыл бұрын
This is amazing!!
@bubson_9216 күн бұрын
Great Job!
@recoilrob32413 күн бұрын
Look at those cam lobes!!! I've seen some asymmetry before but never such an extreme difference between intake and closing ramps. That's just crazy...but hey...it worked!!
@kurtfoulke513013 күн бұрын
Impressive watching you assemble that entire motor using $14 worth of handtools. 👍
@ronnieboucherthecrystalcraftsm12 күн бұрын
side valve inlet and over head exhaust = wow that is some kind of exhaust valve assembly = 2 cams = thank you for assembly .
@hayetzizou6601 Жыл бұрын
he is back les goooo
@PiggyOinkenstein-ts4dp15 күн бұрын
Pretty groovy man. Real Groovy❗🤪👍
@TheRobyMann Жыл бұрын
Sick video
@Lukers_tinkering20 күн бұрын
Fantastic thanks for doing a video... do you have drawings for this engine by any chance?
@jerrodbeck17996 күн бұрын
Dragon Man would be impressed👍🏻
@lenvillemaire475111 күн бұрын
Good work
@joezambrano965123 күн бұрын
Beautiful engine.i wonder who was the genius who designed and b built the engine
@aramirez842713 күн бұрын
Damn.....Thats awesome
@dlfabrications20 күн бұрын
Why are you not adding assembly lubrication?🤔🤔 Did you grease or lubricate the lifters? How often would you lubricate up the lifters.
@localenterprisebroadcastin5971
16 күн бұрын
Not to mention not torquing anything 😂
@johnarnold893
15 күн бұрын
@@localenterprisebroadcastin5971 The torque wrench wasn't even patented until 1931 and it was years until they were being manufactured for general use.
@localenterprisebroadcastin5971
15 күн бұрын
@@johnarnold893 The original torque wrench was invented by Conrad Bahr in 1918…swing and a miss bud
@hunter-cs3em7 күн бұрын
Nice job very well 👏 done😊
@hitthelikebutton9611 Жыл бұрын
Great video! Thank you.
@Aleksandr_Naumov15 күн бұрын
Very good!
@martykath442713 күн бұрын
It may have been initially built with cast iron pistons?? Those modern ones had large domes and ring tech that would be far more advanced than the original ones. I'd imagine this is a "manual squirter" oiling system as I didn't see an oil pump during assy. Haven't bikes come a long way from here.
@lenox9644 Жыл бұрын
This video is the perfect asmr for men.
@kellywheatley80717 күн бұрын
Nice job...
@kh40yrКүн бұрын
AMF Golf Cart with wheelie bars. That would flip the Longhairs at Sturgis. ""WTF?, A 28 2 cam in a muther golf cart"",, lol,,, "GET EM!!".
@YnEoS10 Жыл бұрын
Missed you
@dogpaw77521 күн бұрын
'tis a thing of beauty. but the cam spindle mounting plate being secured by bolts from the inside gives me the yips.
@nandi12313 күн бұрын
The starting motor was a good idea.
@user-fh2lg4ps2j13 күн бұрын
멋진 예술작품입니다 물론 사운드까지
@spiritofmilwaukee19275 ай бұрын
Hey thanks for the video, it will help a lot when I get an F-Head.
@jongirolami497821 күн бұрын
First t time I have ever seen an engine assembled without prelude on pistons/ cylinders etc.
@bmwtravel1100
20 күн бұрын
yes, its odd, but two things: modern oil is light years ahead of 1920's technology, and the clearances on those old air-cooled engines was pretty was generous to start with. that said, yeah I woulda put a few drops here and there.
@wthea7913 Жыл бұрын
Dude this is so out of left field for this channel haha! Love it!
@theroyalaustralian14 күн бұрын
Holy f*** this is right up my ally 😂😂 I can actually restore one of these.😊😊
@williamjames951512 күн бұрын
Sounds like a Hardly!
@biggreasies53715 күн бұрын
I owned one of those JDHs back in the 1970s, completely restored, sold it way to cheap to invest in equipment form machine shop. I see things on that engine that are not quite right.
@jbusta854819 күн бұрын
Cool beans what is the displacement for this engine?
@metricstormtrooperКүн бұрын
Wow, and Harley Davidson haven't progressed one iota since then.
@user-cu8vg5yh3y14 күн бұрын
Оце справжній олд скулл,моя повага хлопцям...
@user-rk1bf4eh2p3 күн бұрын
Very cool something interesting I just turned it on let's see what happens
@JohnTaylor-gy2ps11 күн бұрын
About the same level of technology as the latest model Harley Davidson's lol Check out the Vincent Black Shadow if you're looking for a V twin worth lots of money.
@dntlss8 күн бұрын
I bet those sparks plugs are not easy to find.
@garypease741414 күн бұрын
Thats a first for me. I never new HD made a two stroke.
@h.nguyen4193Ай бұрын
i dont know whats worst the time to find original parts, or the time itll take to make to parts you couldn't find.
@jimevans955015 күн бұрын
Wow. They’re still the same, too.
@nickyborrisino25 күн бұрын
Rebuild every 5000 kilometers 🤣
@PatHaskell8 күн бұрын
Did you happen to obtain 3D data for the engine parts when it was apart?
@Usnz41114 күн бұрын
I think U should scan the motor with 3d or send it to special company to scan it for u cuz its very rear one
@grantbuxton210819 күн бұрын
Wheels through time
@user-vk3ny4fj9t15 күн бұрын
Where abouts are you guys? I have a 1921J in bits that l need to make some decisions about.
@PanheadJeff58 Жыл бұрын
How did you film this? The cam chest is on the wrong side, facing backwards as you're assembling it.
@hyperluminalreality1
29 күн бұрын
JH and JDH. Correct orientation. Go look at pics of a 1928 JDH Harley.
@MAsWorld112 күн бұрын
I do love these but let’s be realistic: it is an IOE after all
@charlespotter7696 күн бұрын
Not much assembly lube but nice job! Even the old tools to the cooling spark plugs. Maybe only 20 people in America know how to build this JD motor. 🖕I'm jealous!
@madaryakar945311 күн бұрын
i wonder why the making of this engine was stopped.! this was the king engine of the road
@dntlss
8 күн бұрын
Probably cause it was too simple.
@dlaws9922 күн бұрын
Where did you find those spark plugs?
@Theogrn18 күн бұрын
What kind of power will these engines make?
@TheIrishAmish18 күн бұрын
Did you lap the case halves?
@marcellucassen803316 күн бұрын
Assembly lube or oil please, I didn't see it, it's important to use when putting an engine together.
@wiwingmargahayu6831 Жыл бұрын
wow its v twin engine Sir
@george1la4 ай бұрын
They were trying every type of valve layout and cylinder head.
@MountainGuerrilla17 күн бұрын
that is a huge crank assembly, it must weigh 60lbs
@SevenDays-3D14 күн бұрын
первый раз вижу на двигателе мотоцикла МАХОВИК, почему сейчас не ставят не понятно ...
@spookydog69594 ай бұрын
how much coffee did you have before the build😁
@Einimas20 күн бұрын
Nice, now it only needs a cvk mikuni.
@user-eo6vw8zq3j16 күн бұрын
Технологически продуманный ! Без компьютера
@JohnSimpson-mv9qm11 күн бұрын
3D it make copies of designs and materials. There’s more than 10😂
@anthonygregory302212 күн бұрын
I tell my partner about interesting projects! All I get is 🦖
@mastergambiarra24 күн бұрын
Como os caras que criaram a harley davidson eram criativos,
@fw14213 күн бұрын
Nice assembly job but not once did I see a torque wrench used. What gives?
@MichaelThomas-ps5qg19 күн бұрын
Awesome stuff man 40k wow
@dwayneterrell19152 күн бұрын
Briggs & Stratton motor OutRunner that hahaha I wouldn't give you scrap money for scrap all it is
@user-rk1bf4eh2p3 күн бұрын
Red Loctite I hope
@HarmonRAB-hp4nk15 күн бұрын
looks like an old 45... dads was a 96 inch 1951 panhead bored. but the Norton commando was faster, cept being a thumper the piston stayed still and the bike went up and down LOL...
@anthonypla713413 күн бұрын
Measures out oil to a fraction of a gram yet doesn't use a torque wrench. Cool engine though.
@n5sdm10 күн бұрын
I know where a 1914 harley team board racer Is....complete and running.
@nigel90021 күн бұрын
I don’t know… It seems if you’re going to go this far with such a rare and expensive engine… clean the rust out from between the cylinder head fins.
@jeffreystpierre689819 күн бұрын
Did you video this from a mirror
@user-mu1oi2jk8e10 күн бұрын
Нельзя было во время испытаний хотя бы вентилятор для охлаждения установить??? и так много косяков во время сборки было совершено
Пікірлер: 155
That old iron running gave me goosebumps. She sounds beautiful.
@pappy451
5 күн бұрын
me too ! loved it !
One of my Antique Cycle buds has a 1913 Harley-Davidson (First H-D) ALKY (pure methanol) burning board-track racer! One speed, no brakes, no throttle, a kill switch that cuts the magneto for "speed control". 119 MPH Laps on the 3/8th mile dirt track at the Creek County Fairgrounds on BICYCLE TYRES pumped-up to 90 PSI (white Firestone's). Total loss lubrication of 50 weight CASTER BEAN oil. Every 5-6th lap, reach between your legs and manual pump the oil pump until it smokes a puff. Think about Glenn Curtis-he bought his frames from brothers in the bicycle trade near Dayton, OH and put his engines on WRIGHT BROS. frames. Now put down an 1/8th mile track of boards, put 40 riders who kicked, punched, spit on each other on a 25 foot wide track at 110+ MPH. It was called "Murderdrome" rather than Motodrome. Many of them became WWI Aviators. I'm working on a street 1916 "ACE" 52* (Bosch Magneto) Vee-twin 1065 cc three speed tranny. Acetylene headlight and all! By 1925, there were at least THREE street motorcycle manufacturers for each letter of the alphabet. EXAMPLE: A: Ace, American Flyer, American Eagle, American Flag, Ace-Hi, All-Bee, A-EZE and 12 more. The "Panic of 1922" killed most brands along with the Model T. When dirt roads turned to mud-pits, an automobile had some advantages. In 1925 there were about 10,000 miles of paved ('improved" that could mean gravel) "highways".
Seeing that thing light and then those flames. The tone is perfection.
Such a beautiful piece of motorsport history. it's so cool to see an old dog spit flames again!
@HarmonRAB-hp4nk
15 күн бұрын
dad sold my bike... I was named after a 1951 panhead... running all those years :-)
Forget putting this on a bike, it needs to be powering a go-kart! I can close my eyes and hear that song behind me as me and my kart break out from under the tree canopy and head into the open country on the IOM Mountain Course.
Absolutely loved coming along for the build, have a blessed week my friend.
Ah the good old days when motors made a small enough amount of horsepower that you could drill holes in the connecting rods to reduce reciprocating weight. Absolutely fascinating. Loved the shaker twin video at the end, hold on tight or it'll be down the street by itself ... it craves to motivate.
@FLORIDAMANIAM-he2lz
19 күн бұрын
Or you could just weigh and balance them
Housing covers, cylinders, flanges etc. have to be tight crosswise in any case, otherwise internal tensions and leaking follows! A good educated and teached mechanic has to know that!! Greetings from Germany!
Best I seen for a very long time, really Love this engine!!!
Great video..Thanks for no music and thanks for running the engine...Great job...
My father had an old '74 when he was in high school in 1939, He was caught doing donuts in the parking lot, and had to eat his lunch in the office.
@dntlss
8 күн бұрын
And he didnt come back and kill the principal the next day,lol, he knew he was caught and took it like a adult unlike today.
Nice! Thanks for putting this together!
So rad to see the old engineering of this motor like the screw in cam bushings/bearings in the case, what a trip. Thanks for showing us behind the scenes
@dntlss
8 күн бұрын
Any particular reason why in the beginning and most of the video hes not using any oil or grease or assembly lube or anything like that? sorry to ask you but seems like he doesn't answer comments.
@seanmakesthings
7 күн бұрын
@@dntlss You know, I really couldn't tell you for certain, but I'll try to make an educated guess here for you. I'd probably guess that assembly lube wasn't too common back in 1928, so using it today is kinda moot. I also believe that this particular engine gets its oil from a hand pump, so I don't know how important assembly lube is gonna be in preventing wear and tear when the engine itself doesn't have a constant circulating oil supply. You could lube the thing up, but it's probably not gonna stay lubed for long, and the oil that needs to get into oil passages and specific crevices might be blocked by gooey assembly lube. One other thing you might research was that in 1929 they introduced a throttle-controlled oil pump, which i have no context for, other than the names and an old article claiming that the throttle-controlled oil pump increased the oiling efficiency and overall health of the engine by a ton. So there ya go, hope my guesses might shine some light on the reasoning behind him not lubing it up like you would a 50s/60s/70s engine found in cars
@seanmakesthings
7 күн бұрын
@@dntlss Read my other guesses first, but here's an alternate theory: he assembled the entire motor for clearance purposes, tore it down off camera, lubed everything perfectly and reassembled it for the final part of the video where he fires it up. Not really sure.
Interesting watching this after Keenan Tatro's videos; despite the difference in time period this still looks like the work of Harley Davidson when compared to later twins.
WOW !!! Super sound ❤❤❤❤❤ Thank YOU!
I just wanted to say thank you for the video on how to access the subharmonic register. Singing basso profundo is freaking fun.
Very nice work!
Wow, the bass tones out of that thing! Sounds like a combination of fart bass and lip buzz. Now I just need to hear a beat over it.
if you need parts for it, check with Reiman Harley Davidson in Kewanee, Illinois. Old Hank Reiman (not his son Roger) was an ace Harley tuner way way back.
Great job. Very good video.
Beautiful!
Beautiful!!
That was really fun!
What a beautiful exhaust sound. You know its a Harley.
@psk5746
11 күн бұрын
Yeah because they all sound like shit
You don't ever want it to stall out and quit, that will leave you stranded by the road. Maybe set your idle screw higher. Not about the sound, or even about the hp (well, if it was used for racing, then it is), it's about getting you there and back without issue or headaches.
@redtobertshateshandles
22 күн бұрын
An old race tuner I worked with often the first thing he'd do was turn up the idle. And on a race two stroke turn it right off.
@choppergirl
22 күн бұрын
@@redtobertshateshandles hard enough to keep an old engine running as it is. once you get it started you don't want it conking out on you all the time. it really swcks if your battery is dead, you have to kickstart or push start it again, or... your compression release is broken. I deal with all three all the time on the farm with this old junk.
@johnarnold893
15 күн бұрын
@@choppergirl Battery, hah, what battery. It's a race engine and uses a mag for spark.
@choppergirl
15 күн бұрын
@@johnarnold893 Fair enough, but a dead battery is huge concern on my bikes that are too heavy to push start and jump on. It will leave you stranded and phwcked. I can push start light cars on flat paved ground and jump in the seat and throw them into 2nd and start them (done that more times than I want to count), but pushing a heavy motorcycle to a running start and swinging a leg over and kicking it in gear without dropping it is beyond my stamina and skill level. Don't want no kickstart motorcycle ever again, you'll wear out your leg or break it trying to get that thing started.
This is amazing!!
Great Job!
Look at those cam lobes!!! I've seen some asymmetry before but never such an extreme difference between intake and closing ramps. That's just crazy...but hey...it worked!!
Impressive watching you assemble that entire motor using $14 worth of handtools. 👍
side valve inlet and over head exhaust = wow that is some kind of exhaust valve assembly = 2 cams = thank you for assembly .
he is back les goooo
Pretty groovy man. Real Groovy❗🤪👍
Sick video
Fantastic thanks for doing a video... do you have drawings for this engine by any chance?
Dragon Man would be impressed👍🏻
Good work
Beautiful engine.i wonder who was the genius who designed and b built the engine
Damn.....Thats awesome
Why are you not adding assembly lubrication?🤔🤔 Did you grease or lubricate the lifters? How often would you lubricate up the lifters.
@localenterprisebroadcastin5971
16 күн бұрын
Not to mention not torquing anything 😂
@johnarnold893
15 күн бұрын
@@localenterprisebroadcastin5971 The torque wrench wasn't even patented until 1931 and it was years until they were being manufactured for general use.
@localenterprisebroadcastin5971
15 күн бұрын
@@johnarnold893 The original torque wrench was invented by Conrad Bahr in 1918…swing and a miss bud
Nice job very well 👏 done😊
Great video! Thank you.
Very good!
It may have been initially built with cast iron pistons?? Those modern ones had large domes and ring tech that would be far more advanced than the original ones. I'd imagine this is a "manual squirter" oiling system as I didn't see an oil pump during assy. Haven't bikes come a long way from here.
This video is the perfect asmr for men.
Nice job...
AMF Golf Cart with wheelie bars. That would flip the Longhairs at Sturgis. ""WTF?, A 28 2 cam in a muther golf cart"",, lol,,, "GET EM!!".
Missed you
'tis a thing of beauty. but the cam spindle mounting plate being secured by bolts from the inside gives me the yips.
The starting motor was a good idea.
멋진 예술작품입니다 물론 사운드까지
Hey thanks for the video, it will help a lot when I get an F-Head.
First t time I have ever seen an engine assembled without prelude on pistons/ cylinders etc.
@bmwtravel1100
20 күн бұрын
yes, its odd, but two things: modern oil is light years ahead of 1920's technology, and the clearances on those old air-cooled engines was pretty was generous to start with. that said, yeah I woulda put a few drops here and there.
Dude this is so out of left field for this channel haha! Love it!
Holy f*** this is right up my ally 😂😂 I can actually restore one of these.😊😊
Sounds like a Hardly!
I owned one of those JDHs back in the 1970s, completely restored, sold it way to cheap to invest in equipment form machine shop. I see things on that engine that are not quite right.
Cool beans what is the displacement for this engine?
Wow, and Harley Davidson haven't progressed one iota since then.
Оце справжній олд скулл,моя повага хлопцям...
Very cool something interesting I just turned it on let's see what happens
About the same level of technology as the latest model Harley Davidson's lol Check out the Vincent Black Shadow if you're looking for a V twin worth lots of money.
I bet those sparks plugs are not easy to find.
Thats a first for me. I never new HD made a two stroke.
i dont know whats worst the time to find original parts, or the time itll take to make to parts you couldn't find.
Wow. They’re still the same, too.
Rebuild every 5000 kilometers 🤣
Did you happen to obtain 3D data for the engine parts when it was apart?
I think U should scan the motor with 3d or send it to special company to scan it for u cuz its very rear one
Wheels through time
Where abouts are you guys? I have a 1921J in bits that l need to make some decisions about.
How did you film this? The cam chest is on the wrong side, facing backwards as you're assembling it.
@hyperluminalreality1
29 күн бұрын
JH and JDH. Correct orientation. Go look at pics of a 1928 JDH Harley.
I do love these but let’s be realistic: it is an IOE after all
Not much assembly lube but nice job! Even the old tools to the cooling spark plugs. Maybe only 20 people in America know how to build this JD motor. 🖕I'm jealous!
i wonder why the making of this engine was stopped.! this was the king engine of the road
@dntlss
8 күн бұрын
Probably cause it was too simple.
Where did you find those spark plugs?
What kind of power will these engines make?
Did you lap the case halves?
Assembly lube or oil please, I didn't see it, it's important to use when putting an engine together.
wow its v twin engine Sir
They were trying every type of valve layout and cylinder head.
that is a huge crank assembly, it must weigh 60lbs
первый раз вижу на двигателе мотоцикла МАХОВИК, почему сейчас не ставят не понятно ...
how much coffee did you have before the build😁
Nice, now it only needs a cvk mikuni.
Технологически продуманный ! Без компьютера
3D it make copies of designs and materials. There’s more than 10😂
I tell my partner about interesting projects! All I get is 🦖
Como os caras que criaram a harley davidson eram criativos,
Nice assembly job but not once did I see a torque wrench used. What gives?
Awesome stuff man 40k wow
Briggs & Stratton motor OutRunner that hahaha I wouldn't give you scrap money for scrap all it is
Red Loctite I hope
looks like an old 45... dads was a 96 inch 1951 panhead bored. but the Norton commando was faster, cept being a thumper the piston stayed still and the bike went up and down LOL...
Measures out oil to a fraction of a gram yet doesn't use a torque wrench. Cool engine though.
I know where a 1914 harley team board racer Is....complete and running.
I don’t know… It seems if you’re going to go this far with such a rare and expensive engine… clean the rust out from between the cylinder head fins.
Did you video this from a mirror
Нельзя было во время испытаний хотя бы вентилятор для охлаждения установить??? и так много косяков во время сборки было совершено
Only 170g of oil, surly that's not enough!?
WHERE ARE THE GASKETS ???