Exploring an Otis door controller
I've always considered Otis to be the most iconic elevator brand, with a very interesting technical history. This door controller is very "Otis". It seems to be well designed at every level with well laid out circuitry, proper input/output protection and no corner cutting.
The controller is surprisingly complex. It's a computer controlled variable frequency drive specifically designed for one application. It can operate on a variety of networks including a proprietary one and CAN Bus, plus accept simple switch signals for use with older equipment.
It takes a surprising level of torque to open and close an elevator door, as the drive mechanism isn't just driving the car door, but also the mechanically interlocked landing door, which has a self-closing bias. Then there are various friction factors like debris in the door track and general wear and tear. But the unit must also be able to detect obstructions and avoid using excessive force to avoid causing injury to users.
To give good torque and precise speed control the controller has an integrated VFD with an IGBT module that converts the incoming single phase supply to a frequency controlled 3-phase supply for the motor.
The classic Otis service tool is a simple handheld serial display and keyboard that will display whatever data the module it's connected to sends it. The menus can be quite deep, and also used for diagnostic and development purposes. A notable warning in the pocket service tool guide says "Warning: This function is used to to monitor and change the RAM memory hexadecimal codes. DO NOT USE THIS FUNCTION FOR ANY REASON!!!"
The unit is designed to self-learn the door operator it's connected to, and work out motor-phase and encoder sequence by slowly trying the door in both directions until it hits a limit switch. By watching encoder movement and switches it can determine position based on door size data entered by the engineer setting it up. During the learning sequence it also displays questions regarding door movement and direction if needed.
The IGBT block looks like it might be a Mitsubishi module like a PS21553-N. If it is then it does require external control from the processor for the phase control. That makes the software in the board's processor quite complex as it has to control the motor phases while also handling network communications.
I specifically avoid using intrusive mid-run video adverts, which means I don't earn as much from my content as other KZreadrs.
If you enjoy these videos you can help support the channel with a dollar or two for coffee, cookies and random gadgets for disassembly at:-
/ bigclive
Patreon supporters get early access to advert-free videos as they are made, and also regular live streams.
This also keeps the channel independent of KZread's advertising algorithms allowing it to be a bit more dangerous and naughty.
Other contribution options are available at:-
www.bigclive.co...
#ElectronicsCreators
Пікірлер: 427
Otis was the first company to produce "safety" lifts which were still safe even when the cable broke. Mr Otis put on a show in an exhibition hall: in front of the public he would be hauled up, then the cable was cut and the lift cabin fell briefly and stopped. That was the foundation of their fortune. The cabin runs on rails in the shaft, and there are brakes against the rails. The clever part is that the brakes are naturally ON, and they are connected to the suspension point of the cabin so that the tension in the cable pulls them into the OFF state. If the cable breaks the brakes immediately come on.
@RedRingOfDead
2 жыл бұрын
Tbh he should've stood in the elevator. It's scary. But damn it would show people they got balls.
@matambale
2 жыл бұрын
Recommend Tim Hunkin's "The Secret Life of the Lift", available on KZread (now at a sharper resolution, and with an epilogue)
@RFC-3514
2 жыл бұрын
@@RedRingOfDead - Er, that's exactly what he did.
@g3intel
2 жыл бұрын
@@RFC-3514 i think he meant standing in the elevator shaft
@peterjf7723
2 жыл бұрын
@@RedRingOfDead What part of "he would be hauled up and the cable cut" did you fail to understand?
I'm in the elevator industry, and have worked for Otis. If you hold down one of the Otis guys that I worked with and tickle them until they cry uncle, they will confess that the best elevators are Mitsubishi. I heard my boss say the same the other day, and he's a born and bred Kone guy. One example of the different philosophies: Mitsubishi Japan decides what capacity you have to install new elevators in your area, and if you sell more elevators than that in a year, they say "Sorry, nope, we're not supplying you because you're gonna rush the job!" Otis is definitely good kit, especially the German stuff, but a lot of the Gen 2 stuff come from China from factories that Otis only own 35% of, and any independent elevator supplier can walk in there and buy Otis kit with their own brand name on. The standard blue SVT service tool is plugged in to do parameters on the standard software. Crazy!
Those two empty footprints next to the WAGO connector at 9:52 are for a LEM current sensor module (CAS 6-NP type) to monitor motor current and the IGBT module is most likely a Mitsubishi PS21563. How I know this is because I work with servicing these type of things and are also used in ThyssenKrupp Universal Door Operator 6300PAx series. I have seen that Infineon processor used in a Schindler (LUST LTI) IDD door operator too. Although this particular OTIS drive is not familiar to me, here in America a variant of the type uses an STM32F103 for the processor. OTIS Germany makes really good stuff, I serviced an OVF20 lift drive made in Berlin a while back and the lifetime counter showed on the tool that it was in operation for over 30 years and made over 2 million run cycles.
@SeanBZA
2 жыл бұрын
Building I used to live at has the original lift in it, with an install date for the motor, gearbox, cables and car of January 1939. Originally FIAM control gear, later on replaced with Express cam switches, which got a little crotchety with time, as the shaft guides were never correctly aligned all the way in the shaft. Eventually we paid Otis to put in the upgrade kit, which replaced the crotchety tappet switches with a tape and magnets, and put in a new controller. Otis underquoted, turned out the existing trailing cables did both not have enough cores, but also failed insulation test, not a problem with 110VDC relays and lamps, but a tiny issue with 24VDC running next to 230VAC power for the car lighting and fan. So in went a nice new 60m of flat trailing cable, 50 cores of 1.5mm copper, and it was commissioned. week later the flat cable relaxed, and moved on the bar, catching on the bottom of the car, and slicing through it. Controller did not survive having 230VAC applied to the 24VDC power rail, though the power transformer, the original FIAM one from 1939, was totally happy, seeing as it only had 2A load on the 24VAC winding, while it was rated for 20A, and the 110VAC winding still had a 2A load from either the brake coil or the retiring cam. New controller and cable under warranty, ouch. There is however a piece of cardboard with a crude drawing I made on it, laminated into the wiring diagram book, with a backing page containing a sign off on the modification by a Pr Eng, where I solved the one issue, that it would trip the breaker for the retiring cam and brake intermittently. Only if you went from top to ground, then called immediately back to top, where it would reliably trip exactly half a floor short. My mod was to move one wire one position, and install one jumper wire, so that the brake coil and the retiring cam each had their own section of the 3 phase breaker, used there with one position being integrated into the safety circuit, like all the other breakers, with a safety link for breaker fail. Also had to train the techs as to how to use MOV devices, they put 110VAC ones on 230VAC, and they exploded. Had to train them on what those numbers mean, and that using a 275 or 430 MOV on 24VAC, instead of the 33 MOV, was not going to provide any protection. Also correct application of them for the job, as they were not really trained much for retrofits, more dealing with installs of complete kits. If you order a lift complete from any of the manufacturers you get a kit, complete down to the last detail, and containing every single fastener for every part, all bagged and marked on a label which floor they are for, and taped to the dorr for there. Shaft as well, all sections bagged, and fasteners all taped to that section. 10 ton kit of parts for a 6 floor building, excluding the container that had the car and MRL drives.
@alexv3780
2 жыл бұрын
Also there is a 68mΩ current sense resistor (marked R14 on pcb) at the input of the igbt module
@FoolishDane
2 жыл бұрын
Yeah, definitely looks like that igtb module, doesn't contain any intelligence or isolation, which would explain all the optocouplers on the inputs and outputs
@Quasam
2 жыл бұрын
I love these kind of replies.
@SLLabsKamilion
2 жыл бұрын
Good to know, I've made a game of finding STM32F103s in the field. They're *everywhere*.
I've been using Wago connectors for decades in many different applications & never had an issue - especially when compared to the competing screw terminals that get over/under tightened etc.
@gabotron94
2 жыл бұрын
It's the knockoff green Chinese ones that can cause trouble (never have for me though)
@petersage5157
2 жыл бұрын
Aren't those technically Wago-to-Phoenix couplers?
@farmersteve129
2 жыл бұрын
@@petersage5157 no, they're Wago proprietary connectors.
@Bananerocs
2 жыл бұрын
I've been using screw terminals for decades in many different applications & never had an issue
@rimmersbryggeri
2 жыл бұрын
Screw terminals can be ok if you use ferrules or solid wires. In saying that probably my least preferred termination type.
A nice change to see well designed electronics instead of 'how cheap can we make this?' Nice 1 Clive
Oh yes, the serial report is still in use. RS-232/DB9 connector can still be purchased on a new laptop. Dell’s “Rugged” line of laptops have RS-232 as standard, and you can have a second port added, during or after purchase. It’s a slotted module. Good old COM1 port! Super versatile and nice to have without a finicky driver for USB-Serial adapter. COM1 just always works and there’s a ton of legacy equipment out there where RS-232 is the only interface available.
@alexisstarsmith1477
2 жыл бұрын
YES! COM1 232 Is still Alive!!!
@SeanBZA
2 жыл бұрын
Yes and also having real serial helps, especially for things that need that proper 12V drive, and which draw power off the status lines as well. FTDI chips do not do that well, and nobody wants to pay the price for the Max232 either, to do the job properly.
@AttilaAsztalos
2 жыл бұрын
Oh nonononono. I'm friggin' DONE adding those damned 323/3232 level shifters to everything I wish to communicate with. I'd much rather install a thousand USB serial drivers (not as if there are more than 3 or 4 different ones, at most, ever, in practice) then bother with the level shifter, the four caps, and a DB-9 ever again.
@NinoJoel
2 жыл бұрын
Yea I build industrial machinery and RS232 is still the more reliable and preferred methode of programming frequency convertrrs and engine controllers.
@AttilaAsztalos
2 жыл бұрын
@@NinoJoel The word you're looking for is "legacy". Same reason you can still buy a 741 opamp, yet no one in their right fucking mind should ever use one in anything designed in the last few DECADES.
That was a nice exploration, and not your average everyday kind of device. Lifts have always fascinated me since as far back as I can remember. And, scared me in equal measure. I can still remember the little old man who used to operate the lift in one of the big department stores in York - They've certainly come a long way since then! That would have been a crafted job in its time, and now anyone can step into a lift, push a button, and off you go. As the old man said "It has its ups and downs, but it's a steady job. You meet all sorts in a lift".
@TrondBrgeKrokli
2 жыл бұрын
Nice pun, "It has its ups and downs" - surely that one was intentional, given that an elevator/lift is the talking point. 😄
@whitesapphire5865
2 жыл бұрын
@@TrondBrgeKrokli Indeed, and the old man was a bit of a wise guy! It would have been in the early '60s and about the time I started at school, but it was his regular line, and given the chance he'd either, get that line in, or, something like it. He was a popular chap with parents and adults alike, and given the torterly pace of that lift, it was just about possible to have a short conversation with him, see depending on how many floors you had to go.
@TrondBrgeKrokli
2 жыл бұрын
@@whitesapphire5865 Nice. Good old quality times. More than enough to make me nostalgic.
@NinoJoel
2 жыл бұрын
When I was in San Francisco around 2014 I met a lift operator in a old records store.
@zovisapphire
2 жыл бұрын
oh hey, another Sapphire o/
"I'd rather have the surprise when I'm expecting it" - best quote
I lived in Reading in the 90’s and occasionally I’d see one of their company vans with their office address on the side. Yes, “Otis, Reading” - always raised a smile :-)
As for the resistors (R1, R2) and the relay: The resistors limit the in-rush current from the mains when you plug it in. Once the bulk of the capacitors are charged the relay kicks in and shorts the resistor. Helps to reduce the stress to all the components on the board AND your fuses dont blow if you switch on the whole system at once, like after a power outage.
@GreatJoe
2 жыл бұрын
I saw something similar done in the Velleman K4040 valve amplifier. It's a neat trick!
Thank god you made this, I've been trapped in here for so long.
Date of construction on label says 2007, so the software is most likely the original from factory then. The pcb is also labeled 2007 in silkscreen label and in copper.
Dang, I came here for "Exploding an OTIS door controller" and only later realized that I misread based on the usual channel expectations. Can we please have a follow-up?
I love seeing inside well designed industrial stuff! Controlling power electronics digitally with microcontrollers/DSPs/etc is becoming increasingly common in well-engineered, complex bits of hardware. Gives you a lot of flexibility and configurability of control algorithms (since it's all done in firmware) - plus you get street cred for doing things the hard way ;) Of course it also introduces the blessing and the curse of being able to "fix" things in software. In the last few years, with specialty power designs, I usually look for microcontrollers rather than dedicated power chips.
Otis Elevator manufactured the first major frame assemblies and several other sub assemblies for the Brunswick Blake Collender company. Which would eventually become Brunswick Bowling. An industry leader in automatic pinsetting equipment for over 65 years!
Looks like R112 and R113 discharge the extra-spicy capacitors. Only thing better than a good MELF is two good MELFs! Properly engineered with adequate voltage rating across the resistors, low impedance copper pours with good separation, teeny tiny trace buggering off to the discharge rail. From the via in the pour between the two resistors, it looks like they're also providing an elevated voltage reference for something or other. I love that the brain box has an "ESD sensitive - donut touch" warning on the PCB and Clive keeps poking it with his finger.
4:30 Canadian here, the Wago thing is just north-american electricians getting mad that you insult our oh so beloved wire nuts. Even though Wago style connectors have been ratified into code for permanent installations. It's mostly the electricians over say, 30-35 that decided they were done learning after they got their journeyman cert. all of the failures i've seen, weren't from material failure but rather installation mishaps or perhaps carelessness.
I was doubting non-screw connectors until I met a retired guy, who was once building test gear for ABB circuit breakers. He told me they had such connotations in their 10kA test station w/o issues. Since then I stopped using the screwed ones. To the MCU: even a STM32F103 from a bluepill board can generate a 3-phase PWM signal with dead time by using a timer and a DMA channel. As long as the generated AC frequency needs no change, the CPU needs to do exactly zero. And the IGBT-module contains 3 half bridges and current sense. It’s capable of generating 400V 3-ohase AC up to ~5..10A. Quiet powerful, but remember the 50€ Chinese variable speed drive units. They are based on such modules. The SMPS with the vipers are good stuff, if you protect them against surges from the grid. But as you can generate revenue/GDP worth a new dishwasher/washing machine, just by saving 50cts of components, they do it. And the vipers/TYnnn‘s/… occasionally disclose their magic smoke finally.
In Finland I usually see either Otis or Kone elevators. The Group Control computers of Kone have a AMD Geode processor (from the early 2000) still in the new models. While the motherboard has had some changes in the last 20 years due to component availability it still looks pretty much the same. Obviously much more reliable than current consumer tech.
@flp322
2 жыл бұрын
In the Netherlands you see Schindler quite often.
@alexbrown1050
2 жыл бұрын
"much more reliable than current consumer tech" seems less likely than "cheaper to use the existing design and software until it cannot be sourced"
@Qwarzz
2 жыл бұрын
@@alexbrown1050 new stuff is cheaper altho you are correct moving to new stuff would cost a lot as well. However current motherboards for example can't be expected to survive reliably for more than 5 years while the 20 year old motherboards are still going. Mostly this is due to electrolytic condensators and can be worked around with proper components. Higher frequencies cause their own issues with lifetime as well. One of the main issues is much thinner tracks which are more suspectible to corrosion. Greater performance has it's downsides.
I have always preferred Schindler to Otis for the simple reason that there is something special about getting into Schindler's Lift and being reminded of one of the greatest movies of all time.
@TheGregEgg
2 жыл бұрын
Bad joke.
@tbelding
2 жыл бұрын
Personally I've always been averse to being Shindled.
That's some beefy components there, kind of reminds me of the old door controllers we used to use on the buses that had a similar programming system and options using a PC and link up system.
@Boom10ful
2 жыл бұрын
Still use those everyday but with a printer cable port or RJ45 port now. Vapor doors I think.
You mentioned that the doors needed plenty of power for weights and friction and such, but left out that they also need enough power to crush baby's heads. Hence the large capacitors to provide that power reserve.
@bigclivedotcom
2 жыл бұрын
And the ability to slam shut from open to increase momentum.
Clive I have to say I have been watching you for quite awhile now, I have no understanding really of any of the things you talk about but you make it so lovely to watch. Best tech mumbo jumbo youtuber :)
I like how even though you have no use for that device, you still don't want to damage it, like the respect someone gives to fine artwork. Also, why no circuit diagram??? ; p
@jeffbuckles
2 жыл бұрын
Circuit diagram? One moment, please.
I think the shaving thing was more kind of a prevention of getting caught by any rotating mechanisms which elevators have plenty of. Just like with long hair things can go bad and ugly sometimes.
@the_tux
2 жыл бұрын
@@GeneCash Jesus… must have been a traumatizing experience.
Otis - "shave your beard if you want a job" Clive - "bye" 😂😂😂
I've heard that spring terminals can better than screw terminals in the long run. When temperature changes, materials expand and contract. That can cause a screw terminals to loosen over time. While spring terminals remain springy.
I read the title of this as "EXPLODING an Otis door controller", and was waiting for the BANG trough the whole video! 🤣
Yes still using this tool even with brand new ones
The service tool exists in two variations. Black and blue. The blue tool has a connection counter that goes down every time it's connected to a unit, and has to be above 0 to allow to perform certain actions on new systems. The black tool does not have this but it is used on older control equipment. There also exist a interface for connecting to a computer, but those are used in very niche cases.
That Otis Blue Box is so rare. Been looking for one for years as I have a Otis 411 lift I look after and we have to program it by hand :( Otis make some of the best gear out there with safety.
@bigclivedotcom
2 жыл бұрын
Psst! eBay and aliexpress.
@phillipgarside4438
2 жыл бұрын
@@bigclivedotcom hehehe spanks :-)
@5:25 - Big Clive - "I used to work in elevators" Me: - I'll bet that was a crowded workspace! I'll get the lights.
Used to be in construction and was always envious of the Otis guys. Always sitting around aha. I will admit the weights they use to calibrate or set the elevators with are heavy though. They were always the same guys on the job, and important enough that they were “allowed” to smoke in the shaft even 420 at times. One time my tile company broke a panel of glass beside an escalator that was turned off for the night, covering it completely. Mr Otis was not happy, not for the mess, but because it was off and we didn’t destroy it.
Industrial stuff like this is such a nice change sometimes from the typical consumer Chinese stuff that we all tear apart / fix etc. so refreshing.
You need to make T shirts and mugs that say "one moment please .."
A beautiful circuit board.
A good friend of mine is an elevator tech here in the city. Their field has got to the most in-demand out of all the trades right now, personally I think it's overlooked. Overtime gets thrown at them like crazy, not enough guys to handle the load. Can be a lot of work with all the troubleshooting.
@twotone3070
2 жыл бұрын
So there are currently not enough of them to handle the load? Maybe they need to rAMP up their recruitment?
Twisted pair RS485 comms cable, used by these terminals, is reliable and cost effective. If you used wiring such as ethernet then the surge spikes surrounding elevator electrical noise will make higher speed comms problematic. The cable quality would have to increase, it would need more shielding and would be stiffer and less flexible to install. All the practicalities of the hard real world conditions are in this design. IMHO, you are looking at the best quality of industrial designs.
A building I worked in for a while had a reliable but very slow old Otis elevator. Someone (necessarily clumsily) altered the name OTIS above the controls to OTIOSE…
@tbelding
2 жыл бұрын
Was it really that useless?
Good connector, on a device operating since 2007 and only responded to a command 1000 times! (open 1000, close 1000,up or down, open 1000,close 1000)...
The "final" test. Aptly identified. Clive a much more learned and brave soul than most. :-) 13:30
Nice bit of kit. I can relate to your feelings about electronics vs electromechanical. In my early days the pinnacle of what I worked with were the Ampex VPR2 1” C format VT machines. Loved those. Really well engineered precise mechanisms along with elegant electronics that you could actually repair down to component level. Things started going to pot when the cassette formats like Betacam started to appear. The mechanics changed from precision machining to bent tin and the electronics got more and more complex, in part to allow for/compensate for the shite mechanicals. The final straw was when they moved to storing the signals on tape in digits rather than analogue. By that time, there was nothing field repairable left in the darn things. Pretty much reduced to board swapping. The machines still cost the same as an average house, but they didn’t look like very good value! Ah, nostalgia…. :)
@idjtoal
2 жыл бұрын
Same story with everything else, everywhere. All gravy and no meat.
BigClive at 1.5 speed is hilarious. I was previously listening to David Vizard Performance on YT who speaks slooooooooowly and forgot to change it. Oh well, back to the start.
Seems like your typical posting schedule is exactly when I'm looking to sit down and wind down for the night. These videos are like therapy for me!
The board says 2007 in a few places. So it seems that the software version might be the original one, or close to that, which is impressive.
I had the pleasure for the first time this year to work with Germans at Siemens. I loved every minute. They knew what I was thinking before I had to explain. It was an utter pleasure. What was even more of a pleasure was they laughed their tits off when I mentioned Boris. I think that says a lot.
Ah the bahco sl25 set ... Love em.
"The final test.." Made me laugh more than it should have when he touched the contacts for the capacitors.
Wow, remove the lid and what a compacted PCB unit. Wonderful and powerful engineering at its best, defiantly an open and shut case by OTIS lifts.
I used to be quite suspicious of Wagos and similar (from an early bad experience with the terminals on Grundfos pumps) but love them now and wish the 221 style were available in larger sizes up to maybe 25mm2. It seems silly that they do DIN rail mount large ones but not inline ones. Seen so many melted cables and burned devices due to poor terminations in cage clamps. In the other hand, I was trying to deal with a faulty solar installation recently where it turned out the clips in a Schneider KQ board weren't clamping in properly. It had been installed correctly, worked correctly for a while then just decided that it didn't want to clamp in properly. Not all the phases were present on the MCB output. Took the MCB out, everything was clean and happy, tested the breaker and it worked, replaced the breaker and then the inverter had all the phases back again as it should have. There was nothing obviously wrong with the MCB but it was definitely the spring clip things at fault.
Ridiculing the "very very expert" 👍👏
13:46 I never regret watching because of gems like this.
The PCB itself was made by Würth Elektronik. Fantistic quality. (I've used them for my own desings at work).
@rpavlik1
2 жыл бұрын
I thought that looked like their logo on the back.
Because synchronous motor control is such a common thing these days a great many general purpose micro-controllers can do the job. The capability is built into the PWM and ADC modules. The cleverness is being able to configure them to be synchronised to each other and sample currents and voltage at precise times.
That's a thing of beauty right there Clive.
I just found this on reddit, love it when you talk lifts fella!
Still use for the newest stuff in NA. Module 1 is ocss, 2 is mcss and 4 is dbss. The whole Elevator. They only show when communicating. We call that a glide controller.
I love the comment to "Benno" - nice touch!
A friend works for Otis..20 yrs.. he makes excellent money.. I see this stuff all over his garage..At 215k a year a service fuel included and you get to use it personal use.. I'd shave...
I can't wait for the part 2 with the schematick.
The building I look after used to have several old electro mechanical lifts, the control gear was amazing I will try and find a photo
In early 2000 I was a computer consultant on a project at UPS. They had a requirement that all male employees be clean shaven unless they had a religious reason for having facial hair. I have a beard, and did not shave it because I was not an employee. So, I can totally see Otis being the same way.
@gabotron94
2 жыл бұрын
Great case of "--You cant do that! Who's your supervisor!? --Eh, myself, I'm on contract"
@tronixfix
2 жыл бұрын
UPS? My mailman got a beard
@anonymous.youtuber
2 жыл бұрын
I remember recruiting an engineer only to be told by the boss “How can you be so stupid to hire someone who is too lazy to shave !” That was in the eighties though. It’s hard to imagine such nonsense would still prevail.
@tbelding
2 жыл бұрын
@@anonymous.youtuber It depends. If the beard is well kept, that's one thing. But there's also the "I haven't bothered to shave, trim, or anything else". Don Johnson being the poster child.
infineon is relatively well known within the pc component industry as vrm (voltage regulator module)/pwm controller manufacturer, also makes mosfets to go with the vrm controllers, would make sense they also makes a processor like the one used in this door controller
Exactly the same processor is used by certain german carwash manufacturer. It seems very capable beeing able to control washtunnels and every other carwash type there is. Washtunnels have tens of lightbarriers, proximity switches, valves, motors, VFD-s and so on. There might be several cars inside at the same time. So lots of controlling to do at the same time by one processor.
I found it moderately funny to look at the struggle to get the circuit board loose from its base fixtures, where I thought there was still a screw or 2 in the center of the board where the L2 and L3 components are somewhat hidden in shadow from C29, C30, C33, and C34. Interesting stuff, indeed.
@TrondBrgeKrokli
2 жыл бұрын
Oh, and yeah, the expression *"Spicy mama voltages"* must be the funniest expression I have heard this week.
IGBT module looks like ffrom Motion SPM 3 family, comes with integrated drivers, but not sense resistors.
@fuzzy1dk
2 жыл бұрын
yeh, the pins that are close are for the low side drive and the pins there are separated in pairs are supply and input for the high side drive
I think you might have a dual motor drive board. The outer doors being separate from the inner doors. If one set of doors fail, the others can still close. Always hated elevators, but got stuck with them in our factory for 14 years. I redrew all the schematics into standard 'electrician's' type. I don't know why AC, Elevator, Automobile and Phone/computer all have to insist on their own proprietary schematics, but use the same parts. WHY CAN'T WE ALL JUST GET ALONG!!!!!!!!!!
@dimitar4y
2 жыл бұрын
because corporations have "sustainable income" and "diversity" quotas to meet, while the CEO's enjoy watching peasants do grunt work in the heat waves that simple cheap robots could've been doing.
@cheyannei5983
2 жыл бұрын
At least for HVAC, the schematics have to resemble/model the real wire runs and connections that a technician would see... Computer schematics I never recall as being nonstandard?
@LachskoenigIV
2 жыл бұрын
The big elevator companies do this on purpose. Without a handbook for their random abbreviations and hidden functions you are pretty much lost. This helps them to keep their expensive maintenance contracts going. There are many small companies offering the same or better service at lower cost. But sadly there is just so much you can do when a fault occurs in these "locked" systems.
@PaulSteMarie
2 жыл бұрын
I've actually drawn dual sets of schematics, one showing the logical connections and the second showing physical layout, including terminal blocks, node numbers, etc. Both are extremely useful
Perhaps the Otisian anti-beard thing was safety-related? Insurer perhaps disliked the prospect of a beard getting caught in the works?
"sorry for the noises" dude half of us are here because it's like electricity asmr
I used to work in elevators. Then I got my own office. 😎😁
I work as customer service for Thyssen Krupp US and I find this stuff SUPER interesting...
Excellent bits of kit thanks Clive
Infineon does make a lot of very nice microcontrollers with integrated motor controls and FET / IGBT driver logic. It's likely the IGBT module is also an Infineon device and it and the micro designed to work well together. Might even be a reference design available :)
Thanks Clive I found this very interesting and uplifting.
I bought one of those IGBT modules once for a project that never happened, but it had a copper heatsink pad, and i did have to design my own part in EAGLE to make a board and thats as far as i got. I believe i still have the module somewhere.
I honestly would not want Beno anywhere near lifts paid or not, you wont have to dig much to find out why. More death beams please 👍
No wonder the capacitors were discharged. You had it upside down and all the electrons fell out.
There's always something satisfying about digging through a relay logic system to find a fault and fixing it, throwing a new circuit board or module at something to fix it just seems boring and lacking challenge. It's been quite a few years since I've been on a site where Otis was doing an install, but here in western Canada quite a few of the elevator techs had beards.
@peto22
2 жыл бұрын
I hate machines built with relay logic from the bottom of my heart. I remember a printing press from the 70s. The customer's complaint was "it doesn't work". The machine had approx. 100 relays, 35 contactors, 15 time relays with different functions, dozens of auxiliary contacts and dozens of limit switches and buttons. Of course, the machine had also been modified many times over the years and best of all, the electrical diagrams of the machine had been lost. With these machines, the standard approach is that by following the wires, you first find out how it should work, then you can determine what doesn't work, and only then can you find the actual fault... by following the wires and without electrical diagrams. These jobs also tend to come as emergency work at 14:30 when working hours end at 15:30
I don’t think I’ve ever laughed so hard about babies being crushed between doors.
OTIS and elevator techs .... I see the spark
I didn't know Infineon made MCUs! I've used some of their H-bridges. I think that IGBT package is a combination of individual IGBT transistors, because of its designation of Q8, instead of U8.
The lift to my sister in laws apartment in Turkey had a lift with outer doors only and no inner door. After a few years they retro fitted some inner doors.
I love me some Wagos. Trouble is, they're stupidly expensive when compared to wire nuts at all the contractor supply shops in my area. Which can be annoying when quoting out work.
Bahco isn't Swedish these days. Bought by SnapOn if my memory serves and production moved from Sweden (initially Spain but there's a vague voice in my head saying that they moved on since to further reduce the payment to workers).
I'm with you on mechanical lifts, nothing like the sound of contactors going in and out when it operates One of the lifts where i worked was upgraded to electronic, though it retained contactors (although replaced with new ones), so we still had the sound I was trained to rellease passengers from lifts and have accompanied lift engineers, it's the safest way to ride on top of the car.
@rjmun580
2 жыл бұрын
Riding on top of a lift car can be necessary but it can only be described as safe when compared with sticking your fingers in an alligator's eyes.
Anyone else annoyed that Clive's analysis was holding the board upside-down... Argghhh! The power was meant to come in top left and flow from there. Oh, it's probably just me. 🤷🏻♀️ Love your vids BC.👍🏻
That was fascinating, thank you Clive. I've always been kinda afraid of lifts, even though I know the amount of safety interlocks they have, I used to always take the stairs, although now I'm a wheelchair user that's not really an option :p Your information about how they work over the years, even just the stuff in passing, has made me feel a little more comfortable using them :) Also, what's the death beams thing about with the capacitors? I saw that one you did on the mobile one, but don't remember it saying anything about capacitors... I'm just getting it's another squirrel-y video that came out?
The two resistors are, most likely, pre charge of the dc bus caps.
EGads, a well designed circuit board, I was starting to fear that they didnt exist anymore!!
q8 is a dedicated ipm module that makes the 3 phases UVW.
I'd rather have the surprise when I'm expecting it ..... just magical
Fascinating, as usual
Just started with a guy installing lifts! if we get any spares and repairs will send them your way clive :)
@SM3Dcreations
6 күн бұрын
the guy i was working with still use the blue machine aswell! 2024 brand new lift install
Was it Otis that built the elevator test shaft in Germany and had the grace to put an observation tower at the top? One of the companies did, and the building is tastefully done on the outside.
@L0op
2 жыл бұрын
that's ThyssenKrupp if I'm not mixing things up
@almostanengineer
2 жыл бұрын
Didn’t Tom Scott do a video on that place, the video was more on the testing of new technologies, and the test shaft than a viewing platform though.
@L0op
2 жыл бұрын
@@almostanengineer yes, but I think back then the technical stuff was more interesting. They remodeled the thing and now it genuinely looks like a wizards tower.
first minutes or so. the device said on it's sticker : "date of Constr" .. this impromptu comment, so didnt get all the info but definitely "2007". Which matches the S/W version
Fun fact: French lift engineers call this entire metal box and/or the pcb inside "The door VFD (Variable Frequency Drive)" !
@bigclivedotcom
Жыл бұрын
The VFD could also be the main motor controller for the lift.
@psirvent8
Жыл бұрын
@@bigclivedotcom Yes and that one they just call if the VFD, hence the term "Door VFD" for the door controller.
Wow ok I’m just back from a rabbit hole I fell into with RE unsaid person scared of death beams 😂 That was a wild ride
Does the little symbol by the infineon chip mean 'keep your pokey fingers off'?
Life at Otis is up and down
A number of generic industrial MCUs put the logic to ease VFD or motor drive as a particular mode or configuration of another element such as PWM control. They then publish a sample or appnote explaining how to do it with all the MCUs containing that peripheral.