Expert Tips: How to Mark Cook Chamber Doors
Тәжірибелік нұсқаулар және стиль
In this video we show you how to MARK out your purged propane tank for the cook chamber doors. This is the first step to making all your cuts for your Stick burner build, so it's super important that you get them right!
As always, be safe and we hope you enjoy the video!
Be sure and subscribe for more videos like this!
If you'd like to get plans to build your own Offset Smoker from a propane tank you can find those here:
sbmfg.net/Offset-Smoker-Plans
If you'd rather have plans to build a Reverse Flow Smoker from a propane tank you can find those here:
smokerplans.net/collections/r...
#smokerbuilder #reverseflowsmokers #offsetsmokers
Пікірлер: 45
Thank you Frank!!
I have seen a lot of how to videos for smoker builds and yours is by far the best one out there. You provide a lot of information that is needed that others do not include. Thank you.
@SmokerBuilder
3 жыл бұрын
Thank you buddy! We try to put the best info to help newcomers all the way to experienced pitmasters.
It's nice to see another fabricator show off skill sets. It's pretty uncommon for older guys to show the shit they've learned over the years.
Information is a great thing when your making videos! Thanks
Here's a tip I've found helpful for making the vertical lines around the tank. Use a roll of magnetic sheet vinyl. 3" x10' for $12-$15 on amazon. Great Videos by the way!
@SmokerBuilder
4 жыл бұрын
Awesome tip bro! Thanks for sharing!
Excellent video!
That is amazing. Watched it over and over. Very professional guys! And thanks
awesome video.... very well explained
That good info looking for a tank right know to build a smoker I see I need to by a new square like you have good tool. Thanks great video's
Good videos!!!!! 💯
This was a great tutorial
@SmokerBuilder
4 жыл бұрын
Thanks buddy!
I didn't know 3 4 5 works on a curve. Interesting. Thanks.
Great information Frank !!👍👍✌✌🇺🇸🇺🇸😁
@SmokerBuilder
4 жыл бұрын
Thanks buddy!
@timothyleger4385
4 жыл бұрын
@@SmokerBuilder 😁😁👍👍✌🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸
love ur videos. I am going to try and make a vertical from a 100g propane tank. Not sure I will do an offset or just smoke from the bottom with an indirect plate.
If ya have the money flange wizard has a large bore pipe center finder. There super handy.
Do you have a complete bung removal and patch video?
I’m in the process of building a 250gal smoker. I have some questions. Are the cut out for the doors 1/4 of the circumference or slightly less? Does the cooking grate sit exactly halfway or slightly lower?
whats the brand/make of that tape measure??
I need one smoker.
Do you have a video on how to layout the holes that are cut in the round ends where the firebox is welded to the cook chamber ?
@Romas65
Жыл бұрын
Man, I've been asking this question from all smoke builders, never get a response. Wish I could,,, been stalling on building my smoker due to not being able to figure this out.
Where the heck did you come across the flexible tape measure? That’s pretty slick.
@hectormarines9231
Жыл бұрын
I second that.
That 10 thing is genius actually lol
Where can I find the tape measure
any particular reason you remove the bungs rather than just plug them and flip it over?
How much would you say a typical 250gal reverse flow smoker weighs?
@SmokerBuilder
3 жыл бұрын
So many things vary, but normal would be around 1000 to 2000 lbs. every one is different depending on customer options.
Can you cut at the 12 and 3 oclock marks or so you have to come in a couple inches on each mark then cut
@SmokerBuilder
Жыл бұрын
Hey buddy, yes you can cut at 12 o’clock and 3 o’clock. The only catch is at the door might be a little heavier at the 12 o’clock position
@johnallen1308
Жыл бұрын
Ok thank you
LOL, the tape measure starting at 10", I had to laugh. Not that you did it, just at the comments. I do similar, all my tapes have incremental inch marks after each 12 inches, so the first inch after 12 has 2 markings, 13 and 1, if i need 6 inches I start at 12 and read the 6 on the tape.
@fredbecker607
2 жыл бұрын
I was taught to burn the first inch.
Would you please tell me what kinda marker you were using?
@SmokerBuilder
3 жыл бұрын
We bounce between soap stone (chalk) for the white or for the black marks. We use the Milwaukee marker red body with a black cap.
@richardwyatt6898
3 жыл бұрын
@@SmokerBuilder thank you very much I appreciate it
@SmokerBuilder
3 жыл бұрын
Not a problem at all!
Do u sell smokers u build? What's your company name?
@SmokerBuilder
3 жыл бұрын
Our company name is Smoker Builder. Yes, we build smokers from UDS all the way to 1,000 smokers with everything in-between as well!