Very Good,I am Electrical Engineer and have 10 years of experience,I appreciate your efforts for the engineers

One of the best explanation using ETAP software.

Thank you Sir, very good instruction. I worked in Relaying field and am returning Appreciate very much.

Well explained sir , before knowing the everything we must know the basics step by step .we Hope more ETAP software videos from you... Thank you...

one of the best explanation i found on youtube. Please sir, keep up the good work!

You make this topic very easy . Nice explanation. Waiting for more videos on relay coordination.

thank you very much. please make more etap tutorials

Hi Muhammad....Thank you for sharing you knowledge...

Thanks man, ure the best !

Great job!

thank you sir please make more etap tutorials

nice one. 👍

Thank you Sir..😍😍😍

Very much well explained with powerful presentation.Need the audio a bit more ....Please.....Thanks & Best Wishes

thanks for presentations.If ask a question about How we can do relay coordination and selection with graphics.Now I am designing a power plant what we 'll select?

Thank you very much Muhammad Hassan. Can you show us how to prepare and run Real time?

thank's

superb

thanks

👍

Please make a video about the operation between recloser,LBS and fuse

hello i want know how relay setting are done in radial distribution system. Either it is done manually or any software available

Hi Have you any video for Relay coordinations?

hello can you please let me know that how we will know that we have to set the pickup value 1.1 ?

I want to setting intertrip from cb1 to cb2, i mean cb1 tripped by ocr1 then send a signal to open cb2. how can i do? Anyway thanks for your video

When using ETAP for calculations like Voltage Drop, Free Air or Underground Ampacity Calculations, etc. Are result compatible with NEC only or other ones as well like Canadian Electrical Code ( CEC), or ....... How we can select either US or Canadian or ,,,,, other codes and standard and /or how do we know which one/s the calculations are based on? Please advise.

How do I add a rectifier to my single line diagram?

Hi, When I set up the transmission line parameters and press ok, it does not save the information. Can you tell me the reason? Thanks.

I add a solar panel on the distribution bus but why the solar panel always in overpower condition in load flow analysis ?

great video but sir relay settings are getting saved what to do ? I'am not able doing relay operation. do help

Sir I have a question related to svc rating Sir svc ki capacitive AR inductive rating Ka kesy find krty hein? Hamein svc ki capacitive AR inductive rating Ka kesy pata chly ga k ketni put krni hai AR kesy nakalni hai

Well done for the video. Please the clicking sounds is very unpleasant. Next time check that sound

Sir by etap we learn whole concept of relay or not

hi.. why do you set the CT primary as 300? can i have detailed explaination?

@Muhammad-Hassan

5 жыл бұрын

just an arbitrary value

@donengo4617

4 жыл бұрын

@@Muhammad-Hassan in fact you choose this value in order to avoid saturation of your current transformer

While running a load flow analysis, it shows an error (the conductor/wire Y coordinate should not be zero). Can you please give an idea to fix these error?

@Muhammad-Hassan

4 жыл бұрын

Dear Sunil, Please follow the instructions in the video, hopefully your error would be rectified. - Check if have entered the parameters of the transmission line correctly. or you can watch this video about load flow analysis. kzread.info/dash/bejne/fntmqdOAZ5isips.html

@mohammadusman3399

3 жыл бұрын

check the impedance parameter, put value for "X" or "X/R" ratio

hello where can get this etap

I cannot get same result in short circuit. Why ya?

relay info is not being saved. any solution please?

after changing the relay editor data it is not being saved, any solution pls?

@tasnimalam9256

3 жыл бұрын

same problem for me

Heh i am interesting in trainings with you how to contact or approcah you

How to change the frequency 60hz to 50hz in etap.kindly explain

@Muhammad-Hassan

3 жыл бұрын

Go to project menu and then select standards, there you will find the frequency settings

@engrmuhammadsamiullah6010

3 жыл бұрын

@@Muhammad-Hassan thank you

Link where to download hehe

thanks

thanks