Hello Sir, if I design a swimming pool on the top of building then how can I assign the joint assignment?

when you are applying the soil pressure all local 3 axis is not in outward projection. so i think you need to do the correction.

@KSSE_Engineer

2 жыл бұрын

👍

How to calculate overturning moment from this load that we applied? Do we need to multiply the load by H/3 for soil pressure cause soil pressure distribution is in triangular shape? Or the etabs assign non uniform load differently so how to find moment for that manually instead of etabs moment that we got after analysis.

@KSSE_Engineer

2 жыл бұрын

You can do manually.

@juliocesarcandovillegas5816

Жыл бұрын

Hi, ¿do you have the moments caused by water and soil? I have an excel sheet but I do not know how to verify if I'm correct.

Hi Sir, can we perform these analysis on our own designed swimming pool like- shallow- deep+ slope + jacuzzi area ? second question is what is the procedure of structure design of pool according to the results kindly make a video for us !

@KSSE_Engineer

8 ай бұрын

Yes, you can . You should determine the internal forces of walls and foundations then design based on your local design code.

Hello Mr I have a question. If I design a swimming pool and put it on the top of building, how can I assign the area spring? Thanks :)

@KSSE_Engineer

Жыл бұрын

In that case you don’t need to add springs , because there’s no soil.

@dillarious

Жыл бұрын

@@KSSE_Engineer can you please explain it the reason why i don't need to add spring?

@KSSE_Engineer

Жыл бұрын

Dear, spring element was used in the tutorial because this pool is located at the ground level, and the pool walls and slab have contact with the soil; therefore, the soil bearing was modeled with springs. In your case, no soil is on the top of the building. You consider the floor slab and wall with a rigid boundary condition.

@dillarious

Жыл бұрын

I got it, thanks for the explanation mr 🙏

10:42 non-continuos deformed shape?

@KSSE_Engineer

2 жыл бұрын

Check it carefully.

Very helpful video can i get the calulation pdf please i didnt find the email

@KSSE_Engineer

2 жыл бұрын

👍 yes

Hello professor, how can i get pdf of manual calculation about swimming pool? Thank you,,

@KSSE_Engineer

2 жыл бұрын

Hi, I am not Professor, I am Ph.D. Engineer, you can send me an email. get it from the channel About.

Could u share the manual design plz

Ka = 120, where you get that? sorry I don't know

@KSSE_Engineer

Жыл бұрын

Plz Join the membership I can provide you the answer.

How to apply load to half height of wall considerng free board

@KSSE_Engineer

Жыл бұрын

Select that area and assign it.

Why do you restrict the walls at the base?

@KSSE_Engineer

2 ай бұрын

What is wrong with it ?

@andresvasquez9675

2 ай бұрын

Did you put them to avoid lateral displacements of the structure? Would it work the same if you don't place them? Its just a question I had.

hello Sir I do not clear how the value of Ka 120 in 00:02:37 in video

@KSSE_Engineer

Ай бұрын

Please check the video if you don’t understand. Then, google how to define the stiffness of spring; there is a lot of information.

can you give me a pdf calculation

@KSSE_Engineer

Жыл бұрын

No,

Please pdf calculation send to me

@KSSE_Engineer

2 жыл бұрын

ok

@user-xw5cr8ku4p

2 жыл бұрын

Please send to me