Engine Sleeve Replacement Complete Engine Repairing and Restoration
Diesel engine sleeve removal and installation. How to engine repairing and rebuild. Rebuilding an engine. How to diesel engine restoration video. How to repair engine.
#howto #repair #engine #restore
Пікірлер: 29
Зубило на блоке ровнять, это прям сильно)
Зачем голоса то ускорили? Серьёзное дело, а мне всё миньоны вспоминаются) Красавчики!
@mamamelaverga8753
Жыл бұрын
Yo creo que en pakistán la atmósfera, en vez de nitrógeno tiene helio.. 🤣🤣
@user-6x6truck
Жыл бұрын
Гильзы молотком осаживать - красавчики?)) да чтоб тебе так машину собирали
@KazakovNik
Жыл бұрын
@@user-6x6truck и какая разница как их забивать ? что пресс что молоток суть одна. Главное что молотком бьет через проставку, а не прямо по гильзе.
@user-6x6truck
Жыл бұрын
@@KazakovNik разница в том, что от молотка происходит местная деформация, а пресс давит равномерно.. Для примера, снимите любой подшипник с вала молотком, хоть и через проставку или при помощи съемника или пресса..
@user-sm7eb5lk8b
Жыл бұрын
@@KazakovNik проставка из мягкого метала чтобы гильзы не повредит
Wow, this was a high-end job. They used brand new head gaskets!
感恩,謝謝分享!
Min 6:55 Soy mecánico, y tengo experiencia en motores, y compresores de pistón... definitivamente esos bulones tiene demasiada holgura, y las camisas de los cilindros no tardarán mucho en volver a rayarse.. deberían de haber corregido esa holgura.. reparar no es sustituir lo roto, sino observar que ha producido el fallo y corregirlo.. Saludos y buen trabajo!
The clothing the men wear looks comfortable.
Когда я увидел как он извлекает гильзы, мне захотелось чтобы его прихлопнуло кабиной. Палку-копалку на плоскости блока ровнять это прям очень как-то за гранью....
Вот куда надо с Белазов возить движки на капиталку 🤨🤔 а то возят в Черногорку и ни хера они не ходят !! А тут хоть как то их и отремонтят надо начальству показать.😎😎😎
❤❤❤
Muito bom 👍👏
Nice1
It’s interesting to watch how people repair with limited resources . How many miles/hours does an overhaul last with this process?
@rasputinthelizard
Жыл бұрын
Not many) A lot of micro-cracks, wrong firing order etc. I watched how they repaired crankshaft and its pain. They even don't cool cylinder liners, just hammer them inside without soft copper padding between liner and hammer.
I couldn’t imagine doing this job without a torque wrench yikes
Motor pay isuzu???
❤😘
😃🇧🇷
🇸🇦❤️🇵🇰
Not the cleanest place, how many hours will this last
A smart fella, would invest in a cheep Chinese parts washer. Then a sand blaster. But I not that smart. Thanks St. Paul.
@mamamelaverga8753
Жыл бұрын
No se si aliexpress tiene distribución en Pakistán... pero seguro que entre impuestos y aduanas.. sale la torta un pan... y así por lo menos tienen entretenido al aprendiz... mientras limpia, observa las piezas y los defectos... las máquinas no hacen eso.. 😇
Писец прям такие специ.... куда там.... а как машину в сто загонишь все морды тупые делают не знаем не можем ... пиздеть все молодцы...
Min 18:30 Unos genios 👍🏽👍🏽 wow