Electricity out of thin air. Static electricity by Nikola Tesla
Ғылым және технология
Watch this video how to collect electricity from the air. Such static electricity was used by Nikola Tesla in his laboratory. Subscribe to the channel, hit the bell kzread.info...
To make this device, you need two copper plates, a capacitor and a magnet.
Copper plates act as antennas to collect static. Such a generator can work indefinitely and generate free free energy.
If you are interested in the topic of free energy, see my selection of videos on this topic - • Свободная энергия
Please follow me on:
+ TikTok: / crazy_black_hacks
+ Instagram: / crazy_black_hacks
+ Facebook: / crazy.black.hacks
+ VK: public192035998
Thanks for watching!
#CrazyBlackHacks #electricityfromair #staticelectricity
Пікірлер: 223
Capacetor was charged and light glow by the charge of capacetor.its not a big thing
@stravs8097
Жыл бұрын
330uF is a tiny storage capacity for an LED that are usually rated at 2V 30mW. Even if I use 12V battery source through a 1k resistor, and a 330uF capacitor in parallel to bleed off through an LED it will only stay on for like 1 second once the power is switched off. If it's a trick, it's being done some other way.
@bsrcat1
2 ай бұрын
@@stravs8097 so what if you stacked 2030 batteries inside a capacitor case. I am pretty sure that it will light up an LED easily I don't know what the copper plates and the wound magnet/capacitor is going to do other than sit there and look pretty but the LED will light up Hahaha.
you can improve this with these: 1- make the plate much larger, with holes. aluminium mesh will do. those holes will allow air flow. and it has sharp point. the negative ions get out of thr sharp points. 2- no need for coil and magnet, just put the plate as high as possible on the roof. and e other side commected to a one meter nail in the ground. 3- every meter hight will give you 100 volts more. so, as large as possible, as many as possible sharp point, and as high as you can get your structure going. this gives you real usable electricity. 4- this experiment that you made is beautiful. it is a night lamp, free for ever.
@halox585
2 жыл бұрын
did i really do that?
@shranoscryptinity8190
2 жыл бұрын
where can i find an explanation on how this works?
@1EQUALS-INFINITY
2 жыл бұрын
How about the pipes in your sink?
@justincosby2258
2 жыл бұрын
@@shranoscryptinity8190 look up atmospheric electricity here on youtube. Lots of videos explaining it. Im not 100% sure as Im not totally aware I completely understand it. But I think it is just caused by a difference in concentration of ions at different heights in the atmosphere. The greater the distance the higher the current. But extracting it is difficult.
@Greg_Chase
Жыл бұрын
@@shranoscryptinity8190 The coiled wire wrapped around the magnet sits atop a capacitor. Look up 'LC resonant circuit' - the two large-ish metal plates are like a radio antenna. Are there lots of radio waves in the air? Yes there are. That's how your car radio works. It's how your cellphone works. Lots of different frequencies too. Lots. The metal plates are like the antenna of a radio. They pick up radio waves that are already in the air. How did the radio or cell phone waves get into the air? By the radio station; by the cell phone company you subscribe to. The LC resonant circuit has electricity flowing through it, back and forth, created by the radio waves plucked out of the air by the large-ish metal plates. And since the metal plates conduct electricity, and are connected to the LC resonant circuit that has electric current running back-and-forth, if the LED is connected across the two metal plates, that allow the electric current to flow through the LED light. And that's why the LED light - lights up. What this is, is - a very basic radio receiver that can only pick up one frequency. It's like a radio that only picks up one station.
Capacitors discharge suddenly and don’t provide a steady flow of electricity to provide a steady light. Magnets without a movement by a coil or the magnet itself will not generate electrical current. You did a great job of concealing the real source of the power! 👍👍👍
@Insightful_Inquiries
Жыл бұрын
What do you think of the “ATMO-Motors” ?
@tonyromano8337
Жыл бұрын
Graphene slow discharge capacitor ?? Will it work ?
@PhysicsViolator
Жыл бұрын
He added an induction wire under the table which the toroidal coil catches the inductance field and outputs a tiny amount of power.. 😂
@hogandromgool2062
6 ай бұрын
@@PhysicsViolator Definitely wireless energy just not the type he claims ;)
@jeads21
6 ай бұрын
You forget that air is a fluid that is also constantly moving and charged. Have you not gotten shocked on a dry windy day or in a air conditioned room?
Only 4.1k views these deserves way more!! Good work my friend 💯 I’m going to keep watching now
@Kredo800
9 ай бұрын
attend school... that institution deserves more.
@AnOdinaryReaper
9 ай бұрын
@@Kredo800 kids don’t even know what “scalar waves” are or even the term scalar…there’s a lot in school they don’t teach you.
if anyone is still doubting that this works, it's a very simple thing to build & in expensive, build one yourself
Looks like a CIA job. No details given. Lots of wow.
If you look closely you will see that he used a 330 mv capacitor
put a meter across capacitor first to discharge it then try again.
Does top of well and or pit have electrostatic energy?....A building?...A hollow buoy floating in water?
I understand how this work. 💪🏼
So you charge the capacitor? And use the led as a load in a switch
A diode to the capacitor. Trying to prevent reverse charging.🤔 Why dont you show the induction cooker under the table. This setup could work even without the copper plates. Very much fake!
Looks like a simple RF harvester, diodes rectify the signal, and I think the magnet might help amplify it a bit, the capacitor is there for storage, the values on it seem to indicate that to me. Easy enough to light a diode. Now storage and amplification of electrostatics is what we need to understand, I do think that electrostatics (atmospheric electricity) might be the way to go. The question is how to harvest it effectively and "store" it for use.
Discharge the cap first and let's see how it goes
Earth ground is a huge reservoir of electrons / negative ions. When you tap into Earth ground and connect the other side to a metal plate that is more positive. Then the electron will flow towards the positive plate where you can now put a capacitor in between both plate and capture the current flow. Can be captured with a capacitor. Tesla's patent was not for alternating current it was literally for direct current. When you put the diodes going like that in only One direction you are creating a potential difference with one side being more positive than the other.
@robertmonroe646
Жыл бұрын
Although what you're doing here will work simply because you're making one side positive and one side negative. And as the positive side continues to accumulate more positive charge increasing the potential difference.. the negative plate will act as a magnet and attract more negative ions. This process will repeat over and over until you have a large potential difference and are sucking negative ions right out of the air like a vacuum cleaner.
@brianlee9310
Жыл бұрын
Can i see your model?
@WasaMada
11 ай бұрын
Same
if you place this in a vacume chember then what will happend? either increased or decreased the voltage. did you try that?
Charge a nickel plate with negative ions it will attract positive ions and generate electricity
Nice job! ✌🏻👏🏻👏🏻👏🏻👏🏻
@Crazy Black Hacks I've seen atmosphere ion harvesting videos on KZread where the small currents/voltages being harvested using copper antennas (somewhat similar to your work) that were converted to high voltages using step up transformers. It would be very interesting to find out if you've done such experiments. Hope I can learn more from your experiments and how to step up that small voltage to a high voltage frequency current. Looking forward to more of your videos and your discoveries. Please keep us posted.
@lauraluca8378
2 жыл бұрын
You can make a lot of this and connect them toghether în paralel. Will increase your amps
@SinisterShivers
Жыл бұрын
@@lauraluca8378 sounds like what Teslas was trying to do with his towers, he only ended up making one before being disfunded
@enursha13drs
Жыл бұрын
dc - dc step up
Credibility level : sponge-bob is the upcoming president of the United States ..
@Ghost_Bear_Trader
4 ай бұрын
It makes sense that they'd replace the last two morons with a new moron. Credibility Checked
So is it possible to make one the size of a building and power a house or a car or even a cell phone?! Is it simply a matter of scale?
Please do the video again this time short the capacitor and show no charge with voltmeter.
very cool device!
@CrazyBlackHacks
2 жыл бұрын
Thank you friend, I tried!
Hi, what are the different wires please?
You should learn how to solder properly. You are creating cold solder joints increasing resistance reducing efficiency. Heat the work, touch the solder to the heated work, when the work has heated tobthebthe correct temperature it will melt the solder and draw it into the work creating a stronger connection with less resistance
15 Years ago I made a 15 feet high antenna,made from a copper shield ,with a copper net webbing, It went to a huge copper plate from 3/4 copper pipe, Transformer diode and large capacitor, I was collecting 54volts out of the air. In till someone warned me off, and I stopped.
@IturbideZamudio
8 ай бұрын
Hola excelente experimento, me gustaría saber más
@cervejaeconversa6060
18 күн бұрын
Também consegui, porém com duas placas bem diferentes
Where is the schematic and parts list for to build this project? What value capacitor and diode did you use and what do you need to build this? All I see is a demo video on how it's built, but there is no schematic and no parts list.
@kfstevens2370
Жыл бұрын
Schematics Patent 685,957 Value capacitor is 330uf 200wv Diode is IN5408 and the magnet is a simple disk magnet used as a toroid coil. Oh and the copper plates my be burned to create cuprous oxide over the plate. This would help it to work more like a solar cell. That's what the Tesla patent was trying to do.
@Birol731
Жыл бұрын
@@kfstevens2370 Thank you very much for the informations, did you make the experiment and test it ?
@keithtaylor6259
5 ай бұрын
If you look closely you will notice that he used a 330 mf capacitor
Toroids are self shielding,thus they cant be used as pickups.😉😃
Plane engine and static electricty equal turbulence
Is the black ring a magnet or a ferrite core?
@Bank2BankBassfishing
Жыл бұрын
Iron core
He has access to quasi materials or quasi atoms
mini batterry in the capacitor
@dahabitmedi
Жыл бұрын
fake
I wish there was a little more explanation in some of the videos of like what and why but I guess it can basically be figured out
@wildmanfujiami5870
2 жыл бұрын
probably that capacitor was charged off camera. a real atmospheric energy collector needs an earth ground and an element high in the air.
@brettjasonhead3740
2 жыл бұрын
He won't and can't give any details as it fake. Videos like these should be removed
@wildmanfujiami5870
2 жыл бұрын
@@brettjasonhead3740 yeah you could remove everything from that circuit except the capacitor and that LED would still light up if the capacitor is charged.
@brettjasonhead3740
2 жыл бұрын
@@wildmanfujiami5870 so over seeing these fake videos pop up.
Is this a joule thief circuit?
Actually.. I'm not sure if this one is fake or not but the concept is real. Although for this to work the way he's showing it, connecting it into Earth ground would be a lot better. My configuration is without that magnet or ferrit core or whatever that is
@WasaMada
11 ай бұрын
Lemme c
Тоже мне Никола Тесла нашелся. Возми мультиметр и покажи, что кондер не заряжен, если это вообще кондер. Светодиод не нужен продемонстрируй все участки цепи мультиметром.
Were the plates electrostatic charged or was the capacitor pre charged?
@CrazyBlackHacks
2 жыл бұрын
The condenser has not been charged
@brettjasonhead3740
2 жыл бұрын
@@CrazyBlackHacks it will only operate for a short time, unless the magnet is moving and or the plates are charged with static electricity. Quote. The properties of magnets are used to make electricity. Moving magnetic fields pull and push electrons. Metals such as copper and aluminum have electrons that are loosely held. Moving a magnet around a coil of wire, or moving a coil of wire around a magnet, pushes the electrons in the wire and creates an electrical current. Electricity generators essentially convert kinetic energy (the energy of motion) into electrical energy.
@CrazyBlackHacks
2 жыл бұрын
you do not know much especially about the energy of the ether. How matter is formed from matter and information.
@brettjasonhead3740
2 жыл бұрын
@@CrazyBlackHacks please educate me with your understanding of energy.
@legioneuropa7191
2 жыл бұрын
@@brettjasonhead3740 its not about ether, but about radio waves which are everythere. these plateas are antenna and condeser and solenoid are LC circuit. cool device.
Free energy with a Tesla coil in the background. When The LED is touching closes the EMP circuit. Watch free energy channel.
@Birol731
Жыл бұрын
You may be right, did you duplicate the experiment ?
The capacitor was already charged..
Конденсатор зарядил, вот и светится диод😁. Магнит обычный или Коля?
The capacitor top is cut off or cut open to put a battery inside yehaaaa.hahaaa
Please Can this still work in a close system ?
@chuckmaddison2924
Жыл бұрын
Only in the confines of the mental institution.
An odd soldering technique
A kind of radiant energy device, I would like to read the comments of people who made the experiment above.
@robertmonroe646
Жыл бұрын
I have built this device and have experimented as seen and it doesn't work the way he is displaying here. Using one diode in two spots does not increase the voltage of each of those antennas. Now you can use a voltage multipier to make one side for example at least 1,000 volts. Then the force field created around that antenna would attract the opposite polarity ions. This would suck up ions right out of the air.
Конденсатор уже был заряжен😊
@CrazyBlackHacks
3 жыл бұрын
не был заряжен
@user-ew6ps9hh3x
3 жыл бұрын
Был. так как его долгое горение светодиода не показали
Wow magik
Нужно было конденсатор вначале разрядить и диоды припаять в другом направлении, потом дурить народ.
Yüksek gerilim telleri altında işe yarıyor
Are these special magnets??? I want to buy some, but Amazon has several choices. Thank you to anybody that can answer.
@lauraluca8378
2 жыл бұрын
This are usual magnet.
@DavoY2K
2 жыл бұрын
Those type of magnets come out of scrap microwave ovens. Two in the magnetron. CAUTION: Discharge H.V. capacitor first thing.
como de la nada? el imán genera campo magnético, lineas de fuerza , y por inducción genera electricidad
@fredericscriabinoff7612
2 жыл бұрын
En primer lugar, no creo que esa pieza circular sea un imán. Tiene más bien pinta de ser un núcleo de ferrita para hacer un electroimán; no obstante este vídeo es toda una farsa, ya que aunque fuera un imán como dices se necesitaría de una variación del campo magnético al rededor del bobinado que ha hecho. Si no hay variación del campo magnético no se induce ningún tipo de corriente (Ley de Faraday). En todo caso, creo que el LED se enciende porque el condensador estaba ya cargado previamente.
wo bekomme ich so große magneten
I've seen the ferro-ceramic ring called a magnet by at least 1 commenter but it is not. That is a ferro-ceramic ring and not magnetized. He's making a version of what is known as a "joule thief ringer circuit." Yes there is an initial momentary introduction of a battery or other energy "primer" and the ferro-ceramic ring wrapped with wire becomes kind of like a generator...ish. As the electro-magnetic waves move through the wire and ferro-ceramic ring it cheats as a generator only if "primed" with a small amount of energy....it basically reuses the electricity as though it has a high amount of efficiency and only slowly will loss happen but because of the cap holding a charge causes a current that moves through the circuit as a electric/mag wave to renew/re-generate the current keeping the light on...break the circuit for too long and it stops working until you "prime" the circuit again by adding a momentary "primer" charge to the cap. At least I THINK that is how it works if I'm not mistaken. I very well may be delusional, after all, I AM only human!
@davidbolha
Жыл бұрын
Very good explanation though. 🤔🙄👌😆 Thanks !
@mayhemdiscordchaosohmy573
Жыл бұрын
@@davidbolha Thank you. I couldn't believe I still remembered that.
@kingofnothing2260
Жыл бұрын
Doesn't look like ferrite. That is made by sintered powder. Should be though. Not a joule thief though, you need 2 coils on the same core and a capacitor transistor duo across a resister to get higher voltage pulses. Not a joule thief from what I see. Using the coil and cap as a tank circuit to trap a current, likely getting super fast pulses from the circuit, but only using 1 half of the wave with 1 diode. Using 2 can get a full wave, so maybe he's storing the other half to boost a half wave signal to the led?
Still waiting for you to explain why your experiment in its current form will work continuously without any movement around it. You need to explain how and why.
@justincosby2258
2 жыл бұрын
Atmospheric electricity
@legoenforcer7734
Жыл бұрын
without movement my friend? the air is always moving... hehehehehe
@eduardocordeiro825
Жыл бұрын
@@justincosby2258 wdym?
@justincosby2258
Жыл бұрын
@@eduardocordeiro825 the atmosphete itself contains a very strong electric current that can be tapped into. Every few feet you move up into the atmosphere there is a difference in voltage in the air caused by ionization of the gases in the atmosphere. If you can tap into it you have free power. Its what Nikola Tesla was trying to achieve.
@eduardocordeiro825
Жыл бұрын
@@justincosby2258 free power? Isn't there any consequences of that power you are talking? Bc think is impossible to achieve that free power You will lose something when you are gaining power or idk
Wait wait did you just soldered that diode with it's - to the - of the cap?!
THAT WOULD NEVER WORK
I've flagged this channel for being fake.
thos capacitor is a battery..
el sonido a fritura de las soldaduras re de más
Попробуй запустить с бесплатная электроэнергия майнинг ферму
@CrazyBlackHacks
3 жыл бұрын
Не шарю в майнинге у меня один ноут только если его запущу на майнинг не на чем будет работать
@VEGAS_MARC
3 жыл бұрын
@@CrazyBlackHacks Ну тагда продавай электроэнергию прикрываесь установкой солнечными батареями чтобы не посадили 😅
Is it true
Лайк поставил, комент оставил 👍
@CrazyBlackHacks
3 жыл бұрын
Благодарю! Очень приятно
@gal499
3 жыл бұрын
@@CrazyBlackHacks 👍👍👍☺
А магнит простой или неодимовый?
@CrazyBlackHacks
3 жыл бұрын
Простой кольцевой
@razeb1
3 жыл бұрын
в кондере батарея полюбому
это простой приемник, гдето за кадром источник.....
@CrazyBlackHacks
3 жыл бұрын
не факт
Don’t even know what to say this that is six minutes of my life that I will never get back order waste of battery power in my phone and Internet usage
E verdadeiro e funciona segredo e atração e repulção das particulas carregadas as placas são receputores de anbas as cargas os diodos fasem a retificação delas o capacitor e carregado uma so ves para criar a diferensa de potencial e e carregado pelas placas infinitamente pir isto o led acende
Не успел досмотреть видео до конца и уже написал комент ,Извиняюсь! кондер тронули рукой значит он был разряжен
@CrazyBlackHacks
3 жыл бұрын
Напряжение очень маленькое, диод ели горит
المكثف مثل بطارية
And not a word was spoken absurd
Такое статическое электричество использовал Никола Тесла в своей лаборатории та ты шо просто в кондере батарея
@CrazyBlackHacks
3 жыл бұрын
Тесла хитрожопый был у него был доступ к знаниям который мы сейчас не имеем :( может к счастью, а то поубивали бы друг друга
This is false, the capacitor can power that LED for a few seconds being previously charged, or there is a high frequency coil transmitting nearby and the plates receive the signal and it is rectified with the diode, many people will believe this, I study sources of energy and tesla circuits and I know what the tricks are like.
We need to try this on the Eiffel tower using the tower as an antenna for the + Also we should have set ups to harvest second hand the power used from data centers...
@dswmetals02
2 жыл бұрын
Unfortunately this would not work on the Eiffel Tower or any buildings that have say a lighting rod on top of them or anything similar even though the higher up in the air the higher voltage you get but the problem with the Eiffel Tower and everything else is the fact that it's touching the ground which means it's grounded so the positive power is going to get canceled out
@dswmetals02
2 жыл бұрын
However you might be able to take some helium or hydrogen balloons and Float them up with copper or gold plated wire attached but there are many other issues you run into with that as well however it would produce power
What are the two resistors that you installed. You don't show their values, or the direction of their travel as resistance to flow, or allowing flow. And you also left it out in the description box saying all you need is a capacitor. But you clearly installed two resistors of some form.
The electricity is from that tranzistor it can stock electricity work's like a battery
Check his channel all about free energy nonsense stuff
Fake:
@mushmmm1509
2 жыл бұрын
You obviously know nothing about magnets metals and electricity
That capacitor was already charged , capacitors works as batteries also LOL, what a scam :)))
А, так теперь понятно 😁 автор! Даже если не веришь в ад и рай, дурить безграмотное население это ПЛОХО 😁😁😁
How dose it work????
@johnmanlangit4636
2 жыл бұрын
Charged the capacitor and it will work
Фокусник 😂
👏👏👏👍👍👍✌️👏👍
This is just a LC circuit with internal resistance like a buck boost converter . The capacitor and I ductor work together to make a infinite loop of electric which dies from heat diserpation but maybe the plates create a electric field that allows the air to sustain the inductors magnetic field . Hmmm interesting
👍👍👍👌👌👌
fake it is imposible to generate 3 volt to turn on a led with these ridiculous configuration .
👍👍👍👍
@CrazyBlackHacks
3 жыл бұрын
👍🖐😉
FAF !
Круто! Первый раз вижу, что бы человек мог так аккуратно снять оболочку с конденсатора, натянуть на батарейку и это было незаметно... а куча лохов на это повелось.
@CrazyBlackHacks
3 жыл бұрын
Та я не разбирал конденсатор 😂 он рабочий до сих пор
@williamfowler616
2 жыл бұрын
ever hear of a tesla radio and the coil that powered it?
@mayhemdiscordchaosohmy573
2 жыл бұрын
Hahahahaha 🤣🤣🤣
Fake
Lol 😂
100% fake -the hidden battery is inside the capacitor
@chuckmaddison2924
Жыл бұрын
Very likely. That's a technique used in vintage radio. Hide modern part in old so still looks original.
😂😂😂
fake
This is fake.
😂
FAKE
پوخ یمه گده دح
Bollocks.
Esto es FAKE
FAKE :)
Smells like BS
Fack