When I first started watching this series I had some doubts this Corvette would get back on the road. But you have certainly proved me wrong. Thanks for producing these video😊😊😊

@ProblemSolverGarage

2 жыл бұрын

It’s actually already finished and on the road, just haven’t released all the episodes yet

That was a brilliant solution! And I want you to know that I have enjoyed all of your videos! My 77 C3 needs a complete rebuild of its HVAC system and a new wiring harness with the newer blade type fuses. Because of your videos, I have the confidence now to take out the dash and do the necessary work

@ProblemSolverGarage

2 жыл бұрын

Nice 👍 and thx

Dude …How in the world did you figure this one out !!! I am going to watch every one of your C3 Corvette videos at least five times ( guess what car I have ) You young man ..are ..Da Man 👍😎

@ProblemSolverGarage

2 жыл бұрын

Thx 🙏🏻

As someone in the middle of a 71 Corvette resto mod project, these videos are super helpful. Thanks, and keep up the good work.

@ProblemSolverGarage

2 жыл бұрын

Thanks and thanks for watching

@age_of_reason

10 ай бұрын

I think you meant restoration.

First I want to thank you for putting in the time to explain things corvette related the way you do. My question for you is this. After driving I pull into the garage and turn the car off. I'll look at the Tach Needle and it will pin itself all the way to the right, at the 70. When I start the car and drive down the street it will correct itself and act normal. When i turn it off again the Needle jumps back to 70. My second question is this. Can you turn an original 350 motor into a 383 stroker? Waiting to see your answer.

Nice job 👍

@ProblemSolverGarage

2 жыл бұрын

Thx

Thanks again You're just great I was able to fix it

@ProblemSolverGarage

2 жыл бұрын

Thanks for watching

brilliant bro! Thanks.

@ProblemSolverGarage

2 жыл бұрын

No problem

Great vid. I would never know to do that. I just want to get squeak out of my 79 speedo cable or speedo needle connection.

I recently installed a performance distributor on a 72 gmc and it started doing the wobble..how do I fix it? what would you suggest? enjoyed your video

What for wires going in the tach? I have a blazer k5 but my tacho dos not work at all…

Excellent solution for a problem I’m currently having with my 1979 power wagon restoration. Any chance this would be the same fix for a fuel gauge reading empty when full? Too much voltage?

@ProblemSolverGarage

Жыл бұрын

No I believe that would be different

Neat solution. The only thing I would add is soldering the connectors in addition to crimping them on. Those resistor ends are super thin.

@ProblemSolverGarage

2 жыл бұрын

👍

Another great video. Thank you. I have a question: with the purchase of a c3 that runs...what would be my steps to checking out systems? Upgrading systems? I am so lost, but proud new owner.

@ProblemSolverGarage

2 жыл бұрын

Watch the whole series every episode in a row it will give you lots of ideas on how to do things and where to start

@ProblemSolverGarage

2 жыл бұрын

Go under playlist in my channel

why those dont come factory with a shielded signal wire is mind boggling.

My tach reads 700 higher than it should, key on 700, idle around 1500. Any way to recalibrate it back to zero at key on the way it should be?

@chadportenga7858

4 күн бұрын

Depending on the year, there are several videos I've seen showing how to "Rezero" or "Zero" the tach. A quick search should find one.

Is it possible to blow your tach? I think i screwed mine up!!

Do I need to worry about any other problems with my ignition coil?

@ProblemSolverGarage

2 жыл бұрын

If the car runs good and there’s no issues then no

Can improper level of transmission fluid cause that?

@ProblemSolverGarage

4 ай бұрын

No

Tried this today on my Harley, unfortunately it didn't work,I was hopeful,any other ideas?

@ProblemSolverGarage

Жыл бұрын

Sorry not too sure

Lol. At least yours works.

@ProblemSolverGarage

Жыл бұрын

it does 👍

stop saying guys all the time

@ProblemSolverGarage

Жыл бұрын

Hey guys, I will try to stop