Another way worked for mine, I used a hand vacuam brake bleeder pump connected to fuel line to carb, about 10 fast squeezes and good to go

I have an 86 that I converted to electric pump with a carter P60504 a few years ago. This is a very reliable quiet gerotor pump. I used the original metal lines and spliced the pump and filter in just ahead of the rear cab mount on the inside of the passenger side frame rail. It sits for months sometimes but always self primes. The closer the better when the pump also has to lift the fuel.

Thanks for the tip! You know I"m cheering for Big Red

When you feed the fuel pump 18V, it pulls less amps than It does on 12V, meaning it runs cooler, so you're fine to run it on 18V. Now, if you were running it on 6V, you would very quickly burn the windings right out of 'er, because it's pulling more amps. More amps=More heat.

@l0w.key_955

2 ай бұрын

How would I do this for a 2005 Infiniti G35 Coupe -automatic

Improvise adapt overcome. Works everytime

If you ever have to buy a new pump you might try a gerotor style or other positive displacement pump. They will draw fuel better on the suction side.

Thank you , this is the second time I have came back to your video. I first referenced this a couple years ago. I just finished a rebuild and I couldn't remember what I did to prime the pump. Did a search you popped up and it hit me "drilling battery". So double thanks!!. I used a 20 volt because that's what I have, no problem

I certainly didn't believe it until I saw it for myself. Works like a champ!

great hack Alex , That won't hurt anything . Great share !

What worked for me was pulling the line off the carb and filling the line with fuel then plugging it back in.

I don't think it will hurt the pump doing it short term like you do but i wouldn't want to feed 18 volts to that fuel pump all the time.

@TrillYungWavy

2 жыл бұрын

THATS ONLY TO GET IT STARTED

It shouldn’t hurt a thing. It’s just a motor and a small jump in voltage won’t hurt it. Steve Meade is running his truck at 17 volts for his stereo no problem with other electronics

In cases such as this my philosophy has always been, it bursts into flames it was probably not the right thing to do. 😅 you'll be fine.

so it only has 12 volts to the pump when turning the key to on position but the electric pump needs more volts to prime . I wonder if a small capacitor that runs on 12 volts to charge up could be used with a toggle switch to crank the fuel pump then shut off once you turn the key on 🤔. course it would take long time but at some point the capacitor would need a small charge up from power as well. the drill battery is a good start/ ideafor starters 👍

Mount your pump low, so it doesn’t have to pull. OR Way I do it, find the small vent tube that came to the old charcoal canister up front. Shoot a few PSI down the tube, pressurize the tank, and push the fuel to the pump. Works for me. Probably dangerous! Dunno.

@TheGasTap

3 жыл бұрын

The bigger feed line I installed worked perfectly. No more priming issues.

Thanks 🙏🏿 bro 😎 I’m about to go and try this.

Would not of thought of that but it looks like it works and I don't think it would hurt anything short term.

Thanks for the tip !!!!!!!!!!!!

I had similar problem I had to relocate pump lower than the gas tank Gravity fed mounted on the frame rail that fixed it even with a low battery.start up every time

I like the truck...but if I put a magnum in with a carb I would use the front cover and water pump off an LA, with a cam snout extension and run a mechanical pump and be happy losing the serpentine belt setup....or go all fuel injection with pump in tank ....but the carb system is dead nuts simple to fix on side of road....not so much the F.I. system.

Anybody put a one way check valve before the fuel pump? I'm going to try it soon. These pumps are supposed to have one already, maybe not enough to stop fuel flowing back.

The fuel-pump on my 98 Ram Van is on its last legs.....original pump and 280k miles. I let the fuel get too low and got 0-psi on the fuel-rail. Trying to prime it by starting it would just kill the battery. So yeah, I have to do the same thing as this vid shows....kinda sucks.

Naw. Way I do it. Find the old charcoal canister vent under the hood and shoot air pressure down it. It will pressurize the tank and push fuel to the pump. Works every time.

@cesarmendiola8860

Жыл бұрын

Im try this I have direct access to my charcoal cansister on my 2RZ tacoma

Great content thanks for sharing

FYI those little pumps like the one on your tailgate are garbage. The outlet side is pressed in with an o ring and it can pop out easily.

@TheGasTap

Ай бұрын

I’ve been using them for 12 years. Now that I have a bigger feed line I’ve had no issues.

Dude I have a brand new flame thrower & right outta the box the fuel pump NO GO,,,, beat on her with a rubber hammer 🔨 still NO GO!! watch this vid , slammed that 18vts from a Milwaukee fat bottom battery & whaaalhaaa She’s-a-hunmin!!! hooked all the one flame thrower back up , built in volt meter reads 11.3volts I test voltage with fluke at the fuel pump leads & im gettin 10.7volts But she hums/pumps fuel …. So we’re rock n roll!!!! Thank you for unintentionally pointing me in the right direction

@TheGasTap

6 ай бұрын

That’s awesome!!! Best comment on the channel in 2024 so far!!!

Cool tip....👍🤙

Question what did you use to bypass the mechanical fuel pump to add the electrical fuel pump?

@TheGasTap

3 жыл бұрын

Use 3/8 fuel line and route from the new electric fuel pump.

OH SHIT I WOULDVE NEVER THOUGHT ABOUT THIS. my car cranks but no start imma get a 18 v battery

Can I retrofit an electric pump to mechanical?

@TheGasTap

3 жыл бұрын

Depends on the vehicle. It has to have a mechanical pump provision on the block.

you're ok at plus 4v for 30 seconds. it must have some margin.

@TheGasTap

15 күн бұрын

Thank you.

Mr. Jones needs to be let out of the pen✊🏁

@TheGasTap

3 жыл бұрын

He came out today. Going to try tomorrow to get a first rip in 🤞🏼

You could just use a mechanical fuel pump that high output and never worry about doing all that priming. Why don't you do that.? Also a better electric fuel pump will pull the fuel ...mine always has .but I have a good high pressure pump. That little junk fuel pumps the problem..

@TheGasTap

3 ай бұрын

I have a magnum timing cover so I can not use a mechanical pump and yes, I could buy a better electric pump. I ended up installing a larger feed hose to the pump and no longer have an issue with the cheap pump.

Hey what size electric fan are you running

@TheGasTap

7 ай бұрын

16” eBay fan.

@darylholloway4

7 ай бұрын

Thanx and interesting because most sites are saying get fans that put out 3000plus cfm , but what came with my radiator is a 16in 1700-2200 cfm

Just show us how to prime the damn thing

@TheGasTap

10 ай бұрын

Watch the damn video

Another reason I already have a 360 then a Hellcat

L

@TheGasTap

Жыл бұрын

A

I enjoy your videos. Are you saying simply adding voltage to the pump beyond 12 volts allows the pump to prime ? I have a carburetor truck from the 80’s that only has a pump just like yours. The truck runs well and I have no issues starting or running. But, I have a clear fuel filter near my carburetor. I can keep my ignition on for 1-2 minutes and the filter will not completely fill with gas. Infact, I can see that no gas is moving period ? Would adding 18 volts change that ?

@TheGasTap

Жыл бұрын

It’s possible. It could also be the pickup in the fuel tank clogged.