I'll tell you what. I got one of these a few months ago because I wanted a light firewood saw with power and actually oiled the bar. After years of fixing husquvarna saws that don't oil or start, what a pleasure this saw has been.

One of my favorite 50cc saws there fun to build too

The 4910 is an excellent saw. I use it on my tree farm. I would suggest that you invest $10 in a set of captured sprocket cover nuts. On mine, the original flange nuts came loose and the chain jumped. I'm using an 18" bar with the Stihl yellow chain. and have a 20 " bar & chain if needed.

I got the 3510 a few months ago. Hate to say it but I love it. It’s featherlite and essentially no vibration. Threw a vxl chain on and played with the carb and it runs great. Won’t outrun a 72 or 346 but for the trade off of weight. I’ll take it. It’s a limbing saw that can be used one handed. Also worth the crap a catch for running an echooooooo. Light enough to run one handed. Also oils only when the chain is moving not on idle. Threw some 3 pt dawgs on to save the case and keep it off the ground. Jury still is out but for the dollar for value it beats a husqy or still.

You are a beast. Watch your back. You only get one of those. I might pull the trigger on one of these. I have two other echo saws and they never fail to start.

Been watching a lot of Charles Brisco. Looking forward to what you do with it, after you run it stock and muffler modded for a while. These saws are more than 1/2 lb lighter than similar 50cc saws. So, when ported and running good, are amazing bang for the buck. Some years, this saw was almost my main firewood saw, when I wasn't cutting anything big. I haven't run mine for a year now - need to get her back out and let her rip.

Nice little saw there! Have a great weekend buddy! 👍👍👍👍🇺🇸🇺🇸🇺🇸🇺🇸🙏🙏🙏🙏

So, it does not have a purge gas bubble? I like that! Home Depot has this saw now for $279.00 before taxes.

@JandSChainsaw

9 ай бұрын

If you can get it that cheap grab it yes no purge

That is a very nice saw

I love some poplar wood. when dry it will start with a torch

Quick Muffler mod and after about 8 to 10 tanks of fuel the 4910 comes to life

@the-stickman

8 ай бұрын

Just take the mesh out?

its an excellent pro saw in disguise. Par per part its the same saw as the Cs 590. Enjoy amigo.

👍

Ive got a squish band question for ya. I sanded a band and have 6 thousandths difference from one side of the cylinder to the other. I musta been abit heavy handed one side. But anyway how big of a concern is that do you think?

@JandSChainsaw

Жыл бұрын

the base may not be true...

@5150powder

Жыл бұрын

@@JandSChainsaw yea i had thought that. its a cheapo no name cylinder that came on a machine. so i thought id see if i could make it run. the saw runs fine, but i just wondered if it was bad or not.

@JandSChainsaw

Жыл бұрын

@@5150powder as long as it has enough clearance on the tight side it will be fine china tolerances are all over the place

@5150powder

Жыл бұрын

it bothers me. i think ill find someone to machine it. just to true the surfaces up. base and squish. hope the lathe is running well for ya. great to see you at the next level. keep it up! I dont know how you have the time but man you pump some saws out.

How's the old 360 and I would like to see an echo 590 timberwolf

@JandSChainsaw

Жыл бұрын

its still a ok and that may eventualy happen

I was wondering where u got it u got it off ebay?

@mrzanm

Жыл бұрын

Home Depot sells them

@justinweaver8787

Жыл бұрын

@@mrzanm awesome i will go have a look at my local 1 an see thank u

How much does the whole unit weight ?

@JandSChainsaw

Жыл бұрын

Idk but it's lifht even with a 20

Was it a new saw?

@JandSChainsaw

Жыл бұрын

yes

@justinweaver8787

Жыл бұрын

@@JandSChainsaw awesome

Do you have an email or a way I can contact you? I have a few questions about a 365sp I built from a bunch of parts and have a few questions.

@JandSChainsaw

Жыл бұрын

jschainsaw2020@gmail.com

⚜️A good time was had by all 🛶

Those are nice saws...I'ma take a crack at one eventually 🤙🏻😎🪓