+mark janzen Hi, thanks for the kind comment, much appreciated! As it happens I’ve been thinking about doing a ball mill project, I’ll be sure to post a video when I do. Would be good to see a video of your machine if you have one? All the best.

I love how basic and low cost you made your machine yet very functional.i spent a lot of time on mine before i got it to produce perfect visco.i did it but it was far from easy then again i didnt have a shop and fancy tools like some guys but you just showed that's not necessary .cuttos. I would like to see you make a ball mill.thanks for sharing.

Very Nice, just subbed thanks for the video!!!🤟

Hi, is it possible to have a drawing file with measurements. Kind regards

Good ide

Do the disc's of string spin cause a belt or gear system of does just the string collectibg cause them to spin?

Can you show me the link to the 2,50e plan please

Hi i buy this project from you but the powder i use fall out why can you help me? i use very fine Black powder i try with glue at the end but from some reason i can not keep the powder inside! Help me some how thanks.

@PYROGENT

7 жыл бұрын

Hi Jozsef. I see that you purchased the plans a little over half an hour ago, I’m amazed you made the model so quickly! In order to help you I need a little more information please. Do you mean that the powder falls out during the weaving process, or when you cut the fuse off of the model? Have you coated the fuse in a nitrocellulose lacquer?

@PYROGENT

7 жыл бұрын

Hi Jozsef, oh I understand now! Powder falling out during the weaving process is the most common problem when making visco fuse. To stop the powder falling out you must have many factors set up correctly - the rotation speed of the dies (the platforms holding the threads), the draw rate of the threads through the model, the speed and amount of powder that is fed into the threads and all of this must remain consistent. If not, then the thread weave too loosely, dropping powder, or too tightly, squeezing the powder out between the threads. Thank you for the link you provided, it shows that the weaving process is not even and consistent in that design, as can be seen by the second set of (grey) threads, which are not uniformly wrapped around the first set of black looking threads. This causes gaps where powder can fall out, and this is likely to be happening with the first set of threads also. The size of the powder holes in my design are stated in the eBook. I hope this helps.

@jozsefienciu2325

7 жыл бұрын

Thanks again this help a lot I thought is my fault but as you say everything must be all in sync. As i have the materials i will make your machine, by the way i buy your both plan for sure regards József.

How did you make the lacquer

几天不就得碎乎了😂

Sad news here in the world of fireworks: I received info from a pyrowebsite that China put out a ban not to export some specialty items like Flying Fish Fuse! And there's those like me who use it in home made aerial shells. I hope that someone here on KZread would see what I posted here and set up a machine shop for making Flying fish fuse !!!!!! Any takers?

@PYROGENT

6 жыл бұрын

Thanks for your comment Robert. This is a shame, but with the right composition you could make your own quite easily as the fuse weaving process is the same. I've made basic flying fish fuse using my simple fuse weaving machines (I made a quick video about them on my channel). The legality of making and shipping fuse for sale is far more comlicated than learning to make your own... and you'll never run out again! Best wishes.

how much USD would it cost for the plans. want to buy them soon and get started.

@PYROGENT

7 жыл бұрын

Hi Preston, thanks for your interest. Paypal should change it for you automatically, but I believe the price under the current exchange rate would be $6.31 for these plans. Alternatively the first set of plans is available for £2.50 ($3.16).

hey i was wondering since you updated and made new plans can i have the old plans for free please? Thank You! -Kyle McMullin

@PYROGENT

8 жыл бұрын

+KmanMeteor Hello, thank you for your interest. The old plans are for a machine which is more robust and this latest model is intended to give people the option for an easy build - it doesn't replace the old design but instead it gives people different options, so I won't be giving away the original plans I'm afraid.

@KylesYTU

8 жыл бұрын

+PYRO GENT email me and don't be afraid I know it isn't smart to trust a person when they say trust me but I am the person that you can trust. I will not give it away. My email is on my channel you just have to type in the code thing to see it.

Tôi muốn mua dây cầu chì cho pháo hoa

Can you tell me what glue do you use to make the wire burn so slowly, what is that glue usually used for in life?

@Pyrokartoffel

2 жыл бұрын

nitrocellulose lacquer, you can make it by dissolving celluloid ping pong balls in aceton

@rainer5452

Жыл бұрын

@@Pyrokartoffel Is there any other way to make it? I know I can buy it but it is probably cheaper to make it

@Pyrokartoffel

Жыл бұрын

It can be only made from dissolving stuff that contains nitrocellulose, so ping pong balls, smokeless powder or gun cotton

@littlehills739

Жыл бұрын

@@Pyrokartoffel they not making pinpong ball in west now like that might be good time to save some up

@Pyrokartoffel

Жыл бұрын

@@littlehills739 yep

Excuse me, I bought your instructions and downloaded them, but I couldn't open them. Why? I'm interested in your lead machine and want to make one myself.

@PYROGENT

5 жыл бұрын

Hi. Firstly, thanks for your purchase. Sorry that you've had issues opening the download. I'm afraid I don't know what the problem is, given the limited information you've provided. Can I ask for your unique Transaction ID please (provided in the email you received when making your purchase)? I can then trace the order, resend the download link and reset the download attempts.

@user-mq9sf7lf8m

5 жыл бұрын

@@PYROGENT Can you send me the world document format or other world document format directly through Google Mail? Or you can send me the process of making your lead machine directly through KZread. I'm from China. I don't know why I downloaded the files you published. I opened them all in random code.

@user-mq9sf7lf8m

5 жыл бұрын

@@PYROGENT Would you like to know if your waterproof lead is made by rubbing it with nitrocellulose glue? Will the bending of the lead made by the lead machine break the fire?

@user-mq9sf7lf8m

5 жыл бұрын

@@PYROGENT Another problem is that I have imitated one according to the shape of the machine you made. The upper and lower turntables made of half-cut plastic bottles are not installed on a vertical plane. They are a little biased. That will not affect it.

Hello pyro-gent, It has been a long time and i'm wondering if I could please have the plans for free, thank you

@PYROGENT

7 жыл бұрын

Hi Adrian, Thanks for your interest, however I'm afraid not, sorry. I put the money towards other projects, so I won't be releasing the plans for free.

@prestonorr746

7 жыл бұрын

PYRO-GENT I think it's funny people asking for $6 dollar plans for free. you could be charging way more I'll gladly pay only $6

@PYROGENT

7 жыл бұрын

Hi Preston, thanks for the comment. I think it might be because some feel uncomfortable paying for things online - but it's via PayPal so it's totally secure. Hope your build goes well!

how much for the plans ?

@PYROGENT

8 жыл бұрын

Hi William, £5 for this version of the plans - makingfireworkfuse.blogspot.co.uk/2015/08/easy-visco-machine-mk-2.html. £2.50 for the original version, which requires more tooling.

Could you please realise the plans for free

@PYROGENT

8 жыл бұрын

Hi, I'm afraid not, sorry. I put the money towards other projects, so I won't be releasing the plans for free.

what is your paypal account so that I can pay you for the plans

@PYROGENT

6 жыл бұрын

Hi William, thanks for your comment. The link to purchase the plans is available at makingfireworkfuse.blogspot.co.uk/2015/08/easy-visco-machine-mk-2.html , clicking the buy now button on the page takes you to Paypal automatically.

Bana kar dikha

@vinodmatho6722

3 жыл бұрын

Maseen bana kar dikha

@vinodmatho6722

3 жыл бұрын

Fuse