Chucking up to solve the problem. Way to go Shawn.

Good video. That's a good way to rejuvenate an otherwise perfectly good drill.

Nicely done Shawn. That worked great

Excellent video and information. Thanks bud

Nice job on getting it done Shawn. The only way.

Great work mate! I've got the same problem with my drill and i will do exactly like you did. Cheers

@shawnmrfixitlee6478

4 жыл бұрын

Thanks 👍

Nice to see a good fix. Lance & Patrick.

Nice job. Good information. I am replacing my first keyless chuck

@shawnmrfixitlee6478

3 жыл бұрын

Thanks !

Thanks that was a big help 👍

This Worked!! Thank you!

@shawnmrfixitlee6478

2 жыл бұрын

No prob ! Thanks for watching ..

Good tip Shawn.

thank you. greetings from Poland

@shawnmrfixitlee6478

8 ай бұрын

Happy Thanksgiving !

Good job broski

Great job, Thanks for the info

@shawnmrfixitlee6478

Жыл бұрын

No problem !!

Thanks. Damn, I think I'm gonna have to do that on mine

@shawnmrfixitlee6478

Жыл бұрын

it's not bad , works good to !

@davecpgh

Жыл бұрын

@@shawnmrfixitlee6478 yea, just a little extra work

Never tried cutting one off, replaced a couple but they did actually pop off for me easily enough. If they're THAT stuck, then cutting makes sense!

@jimsams1987

3 жыл бұрын

3

So many just throw them away when there's much more use in them... Good stuff bud.

Had the same issue with a black and Decker Now ive the same issues with a aeg battery drill

@shawnmrfixitlee6478

Жыл бұрын

it happens to all drills sooner or later.. the more power the drill has the faster the chuck jaws loose there surface grip.. I have found this to be the easy way to swap the chuck out ..Thanks

My chucks are so worn Shawn, they are difficult to turn, and don't hold drills properly.

Is there a way to get it off without destroying it? I wanted to use this Chuck on a different drill.

@shawnmrfixitlee6478

10 ай бұрын

Yes sir , I have a vid on that as well ! Thanks

Anyone know the chuck thread for these 18v Ridgid drills?

@shawnmrfixitlee6478

Жыл бұрын

1/2x20 or some are 3/8x 16.. thanks for watching

👍🏽

What happens when the Chuck you can't tide it and keeps stops when you put force on it

@shawnmrfixitlee6478

Жыл бұрын

I have another vid on the worst case and How to fix it .. thanks !

My chuck freely spins and the teeth won’t reverse any further than 3/4 of the way closed and won’t move in or out. Any ideas

@shawnmrfixitlee6478

3 жыл бұрын

Try my other vid on this subject , You may need to try it if this one does not work for you . Thanks !

I used a 1/2" drillbit (largest bit in my kit) and now my chuck is stuck. I'm still under warranty so maybe I'll go that rout first! I've drilled a total of like 10 holes so far. This is total BS. My old Ryobi had to come finish the job as the Ryobi's often do! Sure beats my Milwaukee 1/2" hammer drill tho... that recently caught on fire after about only 3 holes drilled LOL

@shawnmrfixitlee6478

Жыл бұрын

Yes sir, take it back .. get you bit out with pliers first..

@misterbulger

Жыл бұрын

@@shawnmrfixitlee6478 the bit is out... the jaws are just jammed all the way open

@shawnmrfixitlee6478

Жыл бұрын

@@misterbulger can you but it in the lowest clutch setting it has and grab the chuck with some channel locks and give it a little turn ?

All these helpless videos show a frozen chuck without a drill bit in it. My chuck has a 1/8" drill bit stuck in the chuck !

@shawnmrfixitlee6478

4 жыл бұрын

you may have to grab the chuck with a pair of pliers and try to get it out . If not watch my other vids on the subject . Thanks !