Correction for the formula, it is correct on screen but I said plus the dado groove width and I should have said minus. The formula is also in the description so feel free to copy it and write it down for future reference, or bookmark this video and come back to it for your next framing project.

that spline trick on the table saw is something I haven't seen before, and is such a good technique! Great video!

@keatonbeyerwoodworking

3 ай бұрын

It's easy easier than making a jig that barely ever gets used. Thanks!

Great video. I'm screenshotting the magic formula because that clicked a lot more easily than Michael Alm's frame video for me. Thanks!

@keatonbeyerwoodworking

3 ай бұрын

That's great to hear! I struggled for a long time until I figured out this formula and now the frames always come out spot on, but one thing I didn't mention was I always test to make sure the picture will fit before glue up. Just in case.

"Honey I said I'd do it, there's no need to remind me every six months!"

@keatonbeyerwoodworking

3 ай бұрын

I know right! Also, I finished the frames and hung them up and my wife's first question was when I'd finish the other three for a different room. Not saying I forgot about them but...

Very nice job explaining the process and an even better job imposing a sense of importance in our projects with the finite time/motivation we have.

@keatonbeyerwoodworking

3 ай бұрын

That's right, you can only do so much, so pick what matters. Thanks for watching and for the comment!

Great job they look great

You have a great table saw. Use that to square the edges. Dado can be made on a table saw in 2 passes even with a regular blade. The way you cut the spline slot is pretty great!! I have found that it is much easier to sand edges is with a regular vibrating sander or I really just run the frame through my router table with a very sharp flush trim bit. Fast ans very smooth.

@keatonbeyerwoodworking

3 ай бұрын

I do use the table saw sometimes, and other times I use the router table to joint boards. Depends on the boards and my mood, but the hand plane is the most satisfying. You're right on the dados being done in two passes with a table saw. Doing a depth pass then flipping the board on edge and doing another. I personally don't like that way but I haven't done it on this saw, on my previous saw that method was a little scary given how much parts flexed on that POS. And good tip on sanding! Thanks for sharing.

I love that, thanks!

Like someone else said, I also took a screenshot of the formula. I’m sure it will save me a headache down the road. Loved watching the video over my morning coffee!

@keatonbeyerwoodworking

3 ай бұрын

Awesome, hope it helps. Sure does make it easier for me to remember how to calculate the cuts. Thanks for the comment Kevin!

Nicely done! You have earned a new subscriber to your channel! 👍👍👏👏

@keatonbeyerwoodworking

3 ай бұрын

Awesome, thanks for subscribing!

Great job , great video. You now have another subscriber.

@keatonbeyerwoodworking

3 ай бұрын

Thank you for subscribing! Glad you enjoyed the video

Great video. I've actually never made frames. I may have to add a few to the project list now.

@keatonbeyerwoodworking

3 ай бұрын

With a miter saw and a stop block they're pretty darn easy. Without those things it's much harder. Then of course the rabbet can be tricky without the right tools but a table saw or a router or a router table will all make quick work of it!

Nice.🙂🙂

great video! I can say I'm definitely guilty of putting off promised projects for years!

@keatonbeyerwoodworking

3 ай бұрын

It's hard to get them done with all those competing priorities, but it's easy to make excuses to put them off too. So there's my philosophizing for the morning and now I'll get back to work :)

The table saw trick for corners is an excellent trick. Zero clearance insert needed for the thin strips, right?

@keatonbeyerwoodworking

3 ай бұрын

It's way easier than a whole jig and if I can do a task without I jig that's always my preference, just another thing to store. And yes, I'd recommend a zero clearance insert. Makes the cuts cleaner and safer to not have that gap the workpiece can get stuck in.

The formula works for the stiles as well correct?

@keatonbeyerwoodworking

3 ай бұрын

Yes, same exact thing for the stiles, just measure the height of the picture you are framing and the rail width/groove width remain the same.

Can someone pls explain how a plane makes it possible to square the sides? Cuz there’s no guide rail or nothing. How does that work

@keatonbeyerwoodworking

3 ай бұрын

The plane will first straighten the edge just like a power jointer does. But in doing so you can be off of square like I was, so by moving the plane over to one side of the board and removing more wood on the high side you bring the edge back to square. It takes time and some practice. It also helps you're taking a little bit off at a time and you can check progress with each pass to see how you're doing. I keep two things with me when I plane, a long level to monitor for straight and a square to check for true. Just check multiple parts of the board when you do it because you can be square in one spot and off in another which just means you should plane the off part. Short version, it's different from using power tools, slower and more concentrated, but a little more fun.

That lumber rack is on a real load test.

@keatonbeyerwoodworking

3 ай бұрын

Yeah, I really need to clear it out and use some of it up

Don’t have a dado stack, or more correctly, my table saw can’t hold one.

@keatonbeyerwoodworking

3 ай бұрын

Good thing there's another option I mentioned. I used to make frames with a job site table saw and a thin kerf blade taking a blade width off with each pass. It just takes longer

KZreadr: "Easy, Simple, DIY" Step 1: buy a whole factory worth of tools ... They turned out great though 👍

@bradwillis6591

3 ай бұрын

There's always one.

@keatonbeyerwoodworking

3 ай бұрын

Yup. A table saw and miter saw. My first ever frames I made with a job site table saw and a cheap Ryobi miter saw. Not quite a whole factory but you definitely need some tools to do woodworking. Glad you liked the frames!