Excellent video, really good camera work, really appreciate the time and effort it took to make this!

@techfixPOV

8 ай бұрын

Thank you very much!

Thanks a lot , realy helped me to repair my v8 Dyson with this problem - Aliexpress - 1.2 EUR per 1 MOSFET plus "small" work

@techfixPOV

2 ай бұрын

Glad it helped

Nice one, thanks for listing the MOSFET needed

@techfixPOV

Жыл бұрын

Thanks, I'm glad if it helps.

I had previously just jumpered this mosfet to get it working, but thank you so much for the part number! Finally wanted to go in and complete the repair since the shorted mosfet drew a lot of current draining the battery quickly.

@techfixPOV

11 ай бұрын

Yes, it would be ideal to replace the mosfet with a new one. I'm glad the video was helpful.

Thank you

@techfixPOV

10 ай бұрын

You're welcome

great job !

@techfixPOV

4 ай бұрын

Thank you!

Awesome video. Question for you that blue wire that you unclipped with white end from mother board, where does the other end of it go to and what is it for? Does it just go through that rubber sleeve tube and wrap around and stick into the sleeve tube just above it ? Thanks and great break down u😮😮

@techfixPOV

3 ай бұрын

The blue wires are connected to a Reed sensor. This sensor closes a circuit when the power selector is in the MAX position. The button has a small magnet applied that activates this Reed sensor. The Reed sensor is a glass bulb that contains two contact blades that change their position when they are in the presence of a magnetic field.

Thanks for video. I've got v10 with same problem. And checked MOSFET and it seems ok. Hope for help. Thanks

@techfixPOV

4 ай бұрын

I recommend that you completely disassemble the electronic board and check it on both sides of the liquid. There are several points on the back of the board that can be very easily affected by liquid and generate this defect that you are complaining about.

How did you get the new MOSFET to stick/solder on the board? Are you using the existing solder that was left on the board from the prior MOSFET?

@techfixPOV

9 ай бұрын

It's better to replace the old solder with a fresh one (leaded solder).

Hello. Do you know the output voltage and amperage values ​​for the ground head motor on the board? Could you please answer?

@techfixPOV

2 ай бұрын

Can you be more specific? I don't know which motor you are referring to.

@muttalippnarbas9262

2 ай бұрын

@@techfixPOV Volts and amperage from the DysonV8 type Vacuum motor driver board to the floor nozzle brush motor?

Bro please do a video for Dyson v12 slim there is no video for this 😢 usually the issue is you have to press many time button on to make it work

@techfixPOV

10 ай бұрын

Ok I will try

Ok , mais quelle est la référence des MOSFET ?

@techfixPOV

20 күн бұрын

Please read the video description.

Howdy and thank you for creating the video! What microscope do you use?

@electronicaaran2796

7 ай бұрын

Hello, what type of mosfet is it? thank you

But it only happened with one of the attachments, not all of them.

@techfixPOV

3 ай бұрын

If only one of the brushes doesn't work, it means that that brush needs to be checked.

Hello, my V7 model looks like the same board. Mine overloads and cuts out on high speed. Do you have any thoughts on what might be causing that? Thanks!

@techfixPOV

4 ай бұрын

Does it stop when you use the MAX button? Try without filters installed. If it works normally without filters, you should clean or replace the filters.

@mrzabie0138

4 ай бұрын

@techfixPOV Thanks for the reply. It doesn't work even when the filters are out. I called Dyson and they said it was most likely a bad motor and since it is discontinued, they don't support the model anymore and don't have parts.

👍

Hello, what type of mosfet is it? thank you

@techfixPOV

7 ай бұрын

The MOSFET is M13C30/ PSMN013-30MLC (N-channel 30 V 13.6 mΩ logic level MOSFET).

@Sama_09

5 ай бұрын

Is that same for v11 too ??

what did you use to de-solder the mosfet chip ? Is this a heat gun and what was the solution that you applied to remove the solder from the chip?

@techfixPOV

Жыл бұрын

I used a hot air soldering station, both for desoldering and for soldering. Temperature 400 degrees, airflow at half power. The applied solution is AMTECH flux.

@dennismartin5041

Жыл бұрын

@@techfixPOV thank you

@donjciii

8 ай бұрын

​@@techfixPOVThank you!

need one for v11 !! if you want a test piece i can mail you mine !!

@techfixPOV

3 ай бұрын

I will try to make a video with the V11 model as well. I think I have one that has this problem.

@Sama_09

3 ай бұрын

@@techfixPOV that is awesome

@benf.7158

3 ай бұрын

​@@techfixPOV Do you have the mosfet part number for V11? Thx

@Sama_09

3 ай бұрын

@@techfixPOV hi man still excitedly waiting for that video :)

@techfixPOV

3 ай бұрын

@Sama_09 Have you seen this video? kzread.info/dash/bejne/laNsqo-BpMXfhqw.html I uploaded it recently.