thanks for a very informative video!

Very nice. I have a mn99 also. Thank you from Cebu.

@morrisrc

Жыл бұрын

Salamat bai, palit na dumborc x6dc hehehehe!

Thats a realy good video. thank you so much! perfect! But the article is sold out.

Nice 😃👍🏻👍🏻

nice

Very informative

@morrisrc

Жыл бұрын

Thanks bro

👏👏👏

Thank you

@morrisrc

10 күн бұрын

Welcome bro

Is there a way i can get this shipped to the uk?

WOW I am impressed, can ch5 ch6 could be use for light bar or rock lights on spot lights ?? Thank you !!

@morrisrc

10 ай бұрын

Yes, but you need another light controller. You can use also controller or board of 9g servo motor.

I traced the pinout on the MN82, same as MN99/MN78? I got VCC 3.3, reverse, headlight, brake, left and right (from left to right looking at the board with the writing up), I plan to add all the lights to the MN82 :)

@morrisrc

6 ай бұрын

Yes, you are right bro I also test the lights.

So the channel 3 and 4 controls the light does that mean it is unusable for winch or 2 speed gearbox?

@morrisrc

5 ай бұрын

It will work at the same time

Hi, i’ve the same transfer cable as yours. However, my left signal, channel 3 & 4 not working. Any advise? Using X6 with X6DC

@morrisrc

Жыл бұрын

When you switch on ur esc does your signal light and head ligjt flashes or blinking? Haven,t you touch or accidentally press the switch in the rx for the blue led? Try press it again.

Serve no MN128?

Can you make vedio about (ysido TX YS7) from Ali express/please

Thanks for your video I appreciate. Is there a possibility while accelerating not to increase the brightness in the white front and red rear lights? maybe keep them fixed. It's an unreal function, right? I have the Bl3F receiver, the function of the led system’s is the same correct? Function all well but I would like fixing the ant and post light during acceleration I don’t like they have more brightness during acceleration. Thanks for your information. 🙃

Sayangnya gak responsif,, lampu mundurnya nyalan ketika throtle ditekan agak dalam. Jd mobil harus mundur kencang baru nyala

I bought the X6 controller and it came with the X6F receiver(no LED support). Can I buy the X6DC receiver and use it with the X6 controller?

@morrisrc

Жыл бұрын

Yes you can buy the x6dc receiver and bind to the x6 transmitter.

will it work with MN78 light module? And did you add any resistors to the lights?

@morrisrc

Жыл бұрын

Yes, mn78 and mn99s light module are the same. I did not add resistor but much better put atleast 100 ohms.

@atlasvltor7260

Жыл бұрын

have you finish it yet?

What about reverse lights? How to do it? I would make my rc car like real one.

I just want to ask what value is the resistors that are connected in each signal wires

@morrisrc

Жыл бұрын

100 ohms

@hunterchadph

Жыл бұрын

​@@morrisrcthanks

@lckuiper

4 ай бұрын

​​@rcthanks for this great video! How is the wattage of resistor? 0.25, 0.50,.. ? Thanks!

@morrisrc

4 ай бұрын

0.25 or 1/4 watts

hi po bumili ako ng gearboxwith370 motor galing din sa gemrc. ano pong esc bagay na gamitin kapag? thanks.

@morrisrc

Жыл бұрын

60A surpass hobby gold/brown heat sink

This connect are same for mn78

@morrisrc

Жыл бұрын

Yes bro I think. I tried it in 1:10 redcat the slot is different. Maybe the mode of the light controller, but its very easy to isolate.

hello....i am new to this......will any dumbo transmitter work with x6dc?

@morrisrc

9 ай бұрын

Yes bro

Pano po kung gagamitin yung 3 way position as winch switch ? Pano po ma open yung headlight without using Channel 4 ?

@morrisrc

Жыл бұрын

Ok lng sir gamitin ng sabay kaso sa off position ng 3way position switch ay nka blinking na agad si headlight hehehehhe!

@glnhobbyworld945

Жыл бұрын

@@morrisrc salamat po sa sagot 🤗 love you po idol

@morrisrc

Жыл бұрын

😆🤣😂🍻👊❤

Boss unsaon if walay stock light board same pa rin ba ang function. Assemble lang man gud akoa dili ko nipalit ug RTR. Ty💪🥰

@morrisrc

Жыл бұрын

Yes bro ok ra bisan wala kay light kit sa mn bisan adaptor. Himo lng ka , palit mga led unya butangi lng ug resistor. Connector na dupont head naa pud mapalit sa shopee.

Lastima a mi no me funcionan las luces frontales las de alta los leds están bien pero el canal no envía ninguna señal

@morrisrc

Жыл бұрын

Have you tried the switch in the rx for the light controller? The rx have 2 micro switch for bind and for the light.

@softyan

Жыл бұрын

@@morrisrc el de tres funciones lo he probado y el 4 canal que es de un toque también no funciona el un canal

Good afternoon po sir saan nyo po na bili and ano ano po yung mga nagamit, nasira po kasi yung reciever ng MN99s ko, bago lang po ako nag RRC wala pa masyadong alam sa mga ganyan, sana po pamansin salamat po

@morrisrc

6 ай бұрын

Bro, add moko sa fb and send me a message.

sir morris pwede po ba sa ESC na YSIDO?? mag.uupgrade po kasi ako 370 aftermarket ang motor

@morrisrc

6 ай бұрын

Pwede naman bro pero di ko palang natry ang brand na yan.

@JIN_1993

6 ай бұрын

@@morrisrc thank you sir

Sir, alin sa x6f or x6dc na receiver ang suitable for crawler? Kahit walang gyro ok na rin po ba yun? Nalilito po ko sa dalawa na yan kung alin bagay. Ty sa sagot.

@morrisrc

Жыл бұрын

Kapag crawler o pang trail ung walang gyro. X6f ok lng din yan. Pero kung gusto mo may ilaw ilaw x6dc sya lng ung rx sa dumborc na may light controller. Pero ako bro ayaw ko ung liliko ka at iilaw ang signal light hehehehe! Bro, kung ako ok na ako sa x6f. Shhhh! Secret natin yan hehehehe!.

@markpiodena1614

Жыл бұрын

@@morrisrc hahaha! Parang xmas tree na yung rc. Sbagay pwede na yung solid light lng sa ch 3. ty boss...

@morrisrc

Жыл бұрын

Hahahaha! Yes ok na ung sa channel 3 bro kahit headlight lng kung magdadagdag sa channel 5 and 6 nlng sa knob.

How do you turn off the lights?

@morrisrc

Жыл бұрын

Hello bro! Do you mean the entire lights? All lights the positive are common so you can place a switch there, controlled manually.

Hello, I'm trying to get some help. I bought a dumbo X6F with lights; it doesn't seem to have a blue LED, and the only lights that work are the indicators. I can also turn the gyro on and off, and that's it. Can someone shed some light on this?

@morrisrc

6 ай бұрын

Your receiver is x6f? Only x6dc has a light controller as far as I know but I'll check it out, the blue indicator is for the lights controller.

@iroshimal

6 ай бұрын

​@@morrisrc my receiver is just like yours, its a x6dc but i dont get any blue light when i Turn it on, just red and green

@morrisrc

6 ай бұрын

There is a microswitch in the light controller try to reset it.

Boss pwedi po ba yang remote sa rgt

@morrisrc

11 ай бұрын

Para sa rgt na rig? Pwede bro palit esc kna din

pwede ranag receiver nlng paliton?

@morrisrc

Жыл бұрын

Oo kung naa kay dumborc x6 o 6channel na transmitter pwede receiver nlng palita unya ibind nlng sila.

Boss ok lang ba sa stock esc muma?

@morrisrc

Жыл бұрын

Bro, need palit esc kasi ung stock 2 in 1 esc receiver board kasi.