Drone Assembly / Starter FPV with DJI 03 on 5” Quad
Ойын-сауық
Everyone who has been subscribing to my channel and to those who have also taken the time to watch my videos, THANK YOU. I am super happy to see when people like my videos and also enjoy when I find out I can improve with something. I take time with my builds and I go through the steps to make sure everything is going to work. You will see me install my GPS underneath a Carbon Fiber Plate, which is very OFF and has been relocated to the top of the Carbon Fiber Plate. The reason I did this is to keep it protected just incase I crash, but I will work on a 3D print instead, in the near future. The GPS being relocated is not shown in the video.
The GPS was still getting Locked in Sats but in order for me to feel more efficient with it, I moved it to the top of the frame.
Check in a bit for updated parts list!
Frame: pyrodrone.com/collections/5-i...
FC Stack: pyrodrone.com/collections/new...
Motors: pyrodrone.com/collections/23x...
Props: pyrodrone.com/collections/5-i...
Пікірлер: 42
Watching 'till end is so satisfying. 🤩🤩🤩. Building one soon 😁😁😁
@djslikk818
Жыл бұрын
👏👏Thanks for that support! The screw set is extremely durable with this kit. Best part is you'll be able to replace the arms if needed by just that one screw.
Nice clean solder 👍🏼
@djslikk818
Жыл бұрын
Thanks for the comment 💪 TBS solder offers a good lead to flux ratio
Great Job. Nice build 🙌🏽🙌🏽
@djslikk818
Жыл бұрын
🙏🙏 Much appreciated, thank you for watching and commenting. I was planning on flying outside but we been blessed some rain, which I don't mind at all.
nice build, Thanks for the video!
Absolutely next level bro!!!
Beautiful quad
Nice build! However one trip into tree branches and Those exposed LED wires would get shredded
Woaaahhh LEDSSS
@djslikk818
Жыл бұрын
👽👽Programable to various colors, all primary colors for sure and the settings can be changed to work with a switch on your transmitter.
NICE VIDEO NICE BUILD . TOTAL COST PLEASE ?
Exelente trabajo amigo y un saludo respetuoso para usted.
Great content
@djslikk818
Жыл бұрын
Thanks! 💪
- What amount of solder do you need to build a quad? - YES
@djslikk818
Жыл бұрын
🤓
Hey Nice Job. Please tell me do you have an issue with the OSD with your Mamba Stack and the DJI O3
Very nice job on the build and video production. The last song is by what artist? New Sub also.
Might be a stupid question but can it hold a GoPro?
Awesome video! Mind if I ask the total cost to build this? I want to do my first
whats the thing under the heat shrink called
Does the gps antenna work fine at this position without free view ?
Is this mamba stack which is used in this build is good one ?
Great job 👏, how did you wire up the buzzer, it has three wire ryt, and you have connected gnd to tx ? And how did you configure on BF.
Excellent build, but it seems like the GPS should have a clear line of sight with the sky, and also the LED wires on the bottom and the LED lights themselves are going to get destroyed.
how did you setup betaflight and blheli for the mamba stack and the motors ? also are you running the motors at slow speed when you are doing the hover test in home ? If you do a bit more detailed video on how you setup the software side of things for this exact setup that would be helpful.
18:54 whats that tool you are using to hold your motor as you tighten the prop nut on top ?
I have the same stack you do but have not build my quad yet. Does the ESC go shield up or down or does it matter? How do you like expresslrs?
@djslikk818
Жыл бұрын
It’ll be a beast when you do ! Right in the middle of ESC and FC, the shield will help where most interference is. TBS receivers are what got me started, when I tried ELRS, WOW I felt more live with the quad. Very responsive but not snappy and my flow if there was any, haha was easier to get into. Packet rate is way higher. Module are coming out with up to 1w in power bringing it up for longer range. Thanks for the question!
Hi mate, I wonder if the GPS under the O3 camera has ever given you a GPS fix? I would definiyely move it on the top (maybe linked to a battwry strap).
Speedy bee has plug in LEDs
build Rx ELRS but take off with TBS :)))
Will it be able to hold gopro 9?
@djslikk818
Жыл бұрын
Oh yeah it can! They included a 3D printed mount
How well does the GPS work inside the frame like that?
@djslikk818
Жыл бұрын
surprisingly well, the end of the video shows sats getting picked up right away but I cut off the video pretty quick. I also mention in the description that it was relocated to the top, when the weather clears up that should be a great time to test how well it holds those sats.
You could save a few grams on motors wiring
@creationlabsinc.189
Жыл бұрын
This isn’t a build where weight is a big deal.
Hey man do you sell these by chance? If you dont you should. And if you do HMU with a price on this build complete BNF(bind and fly)
@djslikk818
Жыл бұрын
Would be interesting to put up for sale, I will let you know! thank you 🦾