FIXED: After looking at this great video, I checked the voltage on the PS Capacitors, they were 24 Vdc, good. So I then looked under the emi can at all the micro chips for cold solder joints. I reflowed all the chip leads with a hot air gun. I then plugged in the power cord, and got the familiar 2 beeps, and the unit started working!!!

@mikhail-pletnev

Жыл бұрын

For me it did not work - the same symptoms after reflowing: no green light, no response to the verified working remote. I believe this type of Bose equipment is developed with planned obsolescence, so to die after the warranty period.

FIXED: I watched the entirety of this video and performed each check. Each check yielded a similar result. I was about to fold when I read several comments stating success with a heat gun directed at and around the microprocessor. After waiting for it to lose heat, the device powered as expected! Nevertheless, this video is excellent, methodical, and informative. Thank you!

This was an excellent display of expertise. Thanks for sharing it with us. I am having the same exact issue with mine, and have become beyond frustrated by the device. I'm beginning to see why you "dropped" it. Word to the wise and laymen alike as stated multiple times within this video those capacitors will hold on to hazardous voltage long after the power has been removed, leaving the inexperienced open to a hazardous shock. I wouldn't bother with trying to repair this device on your own if you're a newbie to electronics. Awesome video! Earned a like from me at least!

I don't know if this video will help me fix mine, but really appreciate the time that went into making it! My Solo was in mode with green light, but then wasn't playing when I started some audio, and it was responding to remote on off. So i unplugged, and replugged... But it won't turn on now. There is a hum from the power supply, and the remote works.

@Rider0fBuffalo

Жыл бұрын

If the stupid thing only had a couple buttons!

The video is already 3 years old but still valid. I found a simple, but somehow strange solution for this problem: I heated the processor compartment, after I had opened it, with a hair dryer on highest temperature setting and then the unit started to work again. The rest of the testing had given me the same results as here in the video. A question? Which one of the parts built in the processor unit is sensitive to temperature? The fault must be with that part, since with a bit of heat the malfunction can be fixed. Its a temporary fix only. The BOSO SOLO stops working once the unit cools down again. A really weird fault. But I have not given up hope that it can be fixed!

I’m having good luck with these atm reflowing the pins on main DSP chip. The units I’ve done this too are working solid so far……

You made me spaz out so bad when you plugged in the cord holding the board on live pads XD Took me a bit to realize it's obviously not a powered cord.

@robkle9223

2 жыл бұрын

Did you ever get it fixed? where's the part 2?

I have looked at one of these solo TV soundbard. Despite the excellent construction and components choice, the device is weak on its DSP, a TI D808K023CPTP4. The bar I looked at had its active-clamp flyback power supply in good conditions with 24 V across the output caps. No response from remote. When I heated up the chip with a hot-air gun while power was off (unplugged) and then re-plugged it, the bar did chime at power on and could play music. Turn it off and it's gone in mute mode again. I warmed the chip again and quickly following Bose site instructions, I could update the firmware. It works again but I'm sure it won't last long. Shame cos' this is a nice piece of electronics with good-quality components.

If I send you mine, would you take a second look? Mine is doing the exact same thing with all the same readings. Even down to the buzz and pitch change when you touch the 26 crystal. Any help would be great, thanks!!

Any idea what the USB socket is for? It's labelled "Service." If I have a processor problem (I think I do) then maybe there's a diagnostic tool available through the USB connector.

Hi there. I have a problem that is a bit different. My unit makes the two tone sound when I plug in the power cable to the wall outlet. But that's it. After that it does not power on. Remote-Control seems ok since it is visible the infrared led functioning through a camera. Any help will be appreciated. Either from you or anyone else here. Thank you.

I know you don't have the motherboard anymore but did you manage to find the output pin to see if you could bypass the IC to turn it on, just a thought?

I have the Solo 10,it had a green light on the front, now it is orange?

Great video. Have you made the follow up video?

Iv got one here that when it’s plugged in nothing happens, no green light when the remote is pressed etc. Have tested the output from the IR sensor and it drops when the button is pressed. If I use hot air and warm up the area under the processor shield a bit (so it’s hot to touch, but nowhere near reflow temps) the unit then turns on when the power button is pressed on the remove and I get a green light, so presuming something under that shield is bad. Going to let it cool down and then try a bit more directed heat on each component and try the power each time until I find the component that needs heat to function and then try replacing.

Hello, I have just had one of these turn up at the Market Harborough Repair Cafe and have already done the same tests as you demonstrated so well, but similarly did not find a reason for the unit turning on the green LED and running. I will be bringing it home next week for a more detailed look. Did you get any further with the repair? If not I will report back if I have any success. Keep up the good work. Kind regards, Steve.

it will turn on now but no volume. we have had it unplugged for a couple of weeks. Suggestions please.

Just a quick question. Have you checked AC ripple on the power supply output? I have the same problem and I found 51V AC ripple. I'm changing the filtering caps. We'll see if that helps...

@dualityrepair4770

3 жыл бұрын

I did. Unfortunately the problem was the custom, non-replaceable IC.

Great vid! Did you ever figure this one out? Can't find the follow up vid so I'm thinking 'no'. I have a dead one aswell, the D1301 doesnt read 24V like in your vid. It maxes out at 1.5V. What does that tell you?

Very well done vid... thorough and properly explained. BUT.. I can't find the follow up video?

Hi there can you or anybody confirm a basic test I checked the fuse without power from underneath the board with a basic bleep metre I got a bleep on fuse but nothing on the next in line that brown vertical block but yours looks slightly different???

I have the same issue, if anyone fixed it, maybe they can share the solution. Lots of these units end up in the trash otherwise

@ramss.6433

4 ай бұрын

Did you solve this?

bluetooth on boss solo 10 series ii does not work. no blue light comes on when pressing bluetooth icon on the remote. I did try with another Bose remote.

Dude, this isn't troubleshooting.. It's a full-on open heart surgery course

Mine won’t turn on after the power blipped. It wasn’t turned on at the time. This happened once before and I fixed it (unplugging and replugging?). now I can’t remember what I did.

Mine works but stops from time to time and won't respond to anything. The front LED remains on. It has to be unplugged and rebooted, then it works again. Sometimes when it stops working a low level hum comes out of the speakers (not the mains frequency but quite a bit higher). As soon as you said "processor" I thought "that will be the problem". Nothing reduces the reliability of an electronic device like a microprocessor! So I doubt I'll be able to fix it.

Hi, I have followed your video several times, and I must say that it is very exhaustive and well done, I was only asking after changing the 2 quartz, what happened? Thanks and good luck

this could actually be a Muting problem : The Processor section cannot send an Unmute signal to the power amp section hence it is stuck in Standby or Mute mode Check the datasheet of the Power Amp IC which pin is the Mute pin and how many volts should be applied to switch it ON from Standby or Mute mode

Sometimes I get the start up chime when I plug it in. The remote then turns it on and if I turn it off the remote will not work. Did you have the chime everytime you plugged in the unit while working on it?

@dualityrepair4770

4 жыл бұрын

No chime.

@plsthxpls

3 жыл бұрын

I have also the same Problem have anyone an Idea? Greetings

I have 240v ac on the two pins and 330v dc on the two outside pins, is this normal being in the uk?

@dualityrepair4770

4 жыл бұрын

Yes 100% normal.

Was there any clips that hold the speaker grill in place ? Mine is loose trying to figure out how to get it to snap tight. I got lucky with the one I bought on eBay for 30 something bucks. The owner said it only turned on, didn't have remote. When I got it the unit was in good shape. I already had a soundbar remote and optical cable. Hooked it up, turned it on and it works great. I recently updated the software on it. Only issue is there a small gap in the speaker cover, dent feel like to wants to slip in place.

What if the remote isn’t emitting LED light? Batteries are in correctly

@RobertAbe

Жыл бұрын

Make sure you check using the front-facing camera on your phone. The back facing cameras on phones have an IR filter and you won't see anything. So be sure to switch it to front-facing.

Mine is doing the exact same thing. All of the same readings down to the IR receiver. Did you ever fix this thing or did you just junk it?

@dualityrepair4770

4 жыл бұрын

I dropped it and damaged the board permanently. Sorry.

@81Lord-Nikon

4 жыл бұрын

@@dualityrepair4770 It's just so damn pretty to just throw away. Found it in a thrift store for $20 and was hoping the last guy just lost the remote and his wife got him a new system :)

Did you wind up replacing the crystals? The DSP may be similar to his one TMS320F2810. Also maybe its the reset chip (TPS3825). There are a few Buck regulators in there maybe one of the voltages is off.

Great video. Did you end up replacing the two crystal oscillators? What was the result? Please, please tell me it resolved the problem. My money has been on the Super IO chip, which would suck because this would be not serviceable.

@fabiobrasca619

Жыл бұрын

Hello On pin 9 of the integrated circuit Fan7384 there are connected a resistor with an sot323 ... the sot323 should be bat54cw but i don't know the resistor value ... while connected between diode bridge and fcd7n60 there is a resistor 1210 with written 75 ||| ... is it a 75 ohm? unfortunately on this card there are some things burned and I can't find the values please help me ... thanks

@tubelife70

Жыл бұрын

@@fabiobrasca619 bat54cw is just a diode which is not current dependent. The valve of the resistor is not that important. Check for open or short circuit to ground at the diode. Resistors are almost never the source of problems in a circuit. Capacitors, MoSFETS, and main logic IC's are prone to internal short circuit conditions in most cases. This is why I was very skeptical that replacing the crystal oscillator(s) would resolve the problem in this system. This board looks immaculate except for the main Processor IC, which by the manufacture's logo looks like it was made by Texas Instruments (tI) and shows signs of overheating. This audio system is basically a no fix, even for BOSE.

@fabiobrasca619

Жыл бұрын

@@tubelife70 Hello thanks for your answer ... yes true you are right but while I was doing some tests the IC fan7384 flared and burned my bat54cw with the connected resistor, the two mosfets fcd7n60, lm5021 was already shorted and a 1210 resistor on which I do not remember if it was written 75 or 750 ... so I need to know both the value of the resistance connected on the bat and that of the resistance 1210 connected to the mosfet fcd to try to get back the 24v ... I have a short on 2 0603 capacitors outside the dsp cage near the optical connector on which I will have to investigate ...

@tubelife70

Жыл бұрын

@@fabiobrasca619 I won't be back to the office until this coming Tuesday, when I will look at the original board and try to get the correct values for you.

@fabiobrasca619

Жыл бұрын

@@tubelife70 Ok ok I owe you ... I am waiting for your news ... Thank you very much

Is there a way to use it with the remote??? I don't have the remote for mine.

@vitosgirl81

2 жыл бұрын

I have this same question! How to connect it to a Bose sound bar universal remote?

So did this fix the unit? Or should I not even bother

@dualityrepair4770

4 жыл бұрын

It did not fix the problem.

Hi I have a question: "" There are two 0603 capacitors out of the cage precisely on the side where there is the usb connector and the optical connector that the tester gives me in short circuit ... Is there anyone who has checked them?

@guevenyilmaz24

8 ай бұрын

Yeah, they are shorted

My unit is reporting exactly as yours. Down to the T. Too bad you we’re not able to do a part 2. I’ll go ahead and replace the crystals and let you know if it worked.

@andyskatman4366

4 жыл бұрын

Have the same issue. Please let me know if it works. Can you please help me with a resistor marking that blew on my main board and now I can't find any schematics to figure out what is its value. the resistor is located on the power supply side next to the bridge rectifier (BR1201) and the component marked with C1224. thanks

@klabawter

4 жыл бұрын

hello, do you have replace the crystals? does it work?

@jamespanda9816

4 жыл бұрын

@@andyskatman4366 sorry it's so late but that seems to be marked as a 75m fusible resister. Hope that helps if you are still working on it

@silviuguseila2552

4 жыл бұрын

@@andyskatman4366 here is a pic of that resistor: imgur.com/Sj3F8hC, ai un mail sa discutam? Ai rezolvat?

Excuse me, I don't speak english very well ... did somedy find a solution ? I have the same problem with that sound bar. Thanks for help ! Je ne parle pas très bien anglais ... quelqu'un a-t-il trouvé une solution à ce problème ? Merci d'avance !!

did you ever get it working

Any updates on this? Replacing the two crystals seems like a good lead.

@dualityrepair4770

4 жыл бұрын

No good updates. I dropped the unit and cracked the board so it’s gone now.

@mrmartin17

4 жыл бұрын

I have one of these with symptoms of powering up lasting for about an hour, then turning off. Usually it comes back on, but it’s off for good at the moment. It started doing this every 6 months but it used to come back on. Now it seems dead. Any good tips for testing with these symptoms? Thanks!

Починить удалось? (Did you manage to fix it?)

I opened the cover exposing the processor used a heat gun to heat everything up , it then powered on so i used a usb and downloaded firmware update installed and seems to be working as it should, so heat gun or firmware update seems to have fixed the issue not sure which but if i had to guess id say the heat gun, seems like a similar problem the original xbox had from heat issue severing soldered connections on the board,??????? your guess is as good as mine.

@fabiobrasca619

Жыл бұрын

On pin 9 of the integrated circuit Fan7384 there are connected a 0603 resistor with an sot323... Can you tell me the value of this resistor please?

Hello, i have had the same problem (wont turn on) but when i plug the power cable there was a beeep beep. After checking all the voltages i found that there was a problem With the remote. Now working.

@fabiobrasca619

Жыл бұрын

Hello On pin 9 of the integrated circuit Fan7384 there are connected a resistor with an sot323 ... the sot323 should be bat54cw but i don't know the resistor value ... while connected between diode bridge and fcd7n60 there is a resistor 1210 with written 75 ||| ... is it a 75 ohm? unfortunately on this card there are some things burned and I can't find the values please help me ... thanks

So did you change the crystals? Did it work?

@fabiobrasca619

Жыл бұрын

Hello On pin 9 of the integrated circuit Fan7384 there are connected a resistor with an sot323 ... the sot323 should be bat54cw but i don't know the resistor value ... while connected between diode bridge and fcd7n60 there is a resistor 1210 with written 75 ||| ... is it a 75 ohm? unfortunately on this card there are some things burned and I can't find the values please help me ... thanks

Where can I find a replacement remote because I just troubleshooting mine using your video and I see my remote doesn’t work even after I replaced the battery

@dualityrepair4770

9 ай бұрын

Other than Ebay, I'm not sure where you'd get a replacement remote.

@ramss.6433

4 ай бұрын

You can use an app if you have a device with an IR port

It's crazy just picked one up, had exactly the same issues, heated it with a hairdryer got it working, played KZread through the TV for a bit then came a loud humming sound so I had to unplug it, turned it on tried again did the same after about 10 mins, then just used it through the TV freeview and it worked way longer so no idea what it's problem is, will try updating firmware and see what happens, no idea why it didn't like KZread but had no problem with freeview, and the under heating baffles me

For what it's worth; I have had two of this model exact Bose Solo sound system devices. They both failed after many years of use. I have replaced the six capacitors of the power supply just to exclude it's not those. But it did not help. I've not been able to repair a faulty Bose solo sound system. The symptoms are the same; the device does not turn on, or it turns on and after a few days of use it dies again. After unplugging the power cord for a short time it comes back but does not keep working correctly. I will attempt to replace these two crystals on one faulty device, would be nice to know if this helps.

@qayqay2754

3 жыл бұрын

Did it help?

@i80486dx

3 жыл бұрын

@@qayqay2754 It did not help. I guess it's just the main propriatiary IC that's broken.

@johnathanpearson3203

3 жыл бұрын

@@i80486dx perhaps it's a overheat problem with the IC.

@i80486dx

3 жыл бұрын

@@johnathanpearson3203 Yes, I'm also thinking the main IC is faulty. As this IC is a Bose proprietary chip it cannot be replaced.

I have the exact same problem, did anyone ever figure it out? I don't want to replace the crystals if it's not going to fix the problem.

@dualityrepair4770

4 жыл бұрын

Don’t replace the crystals. I believe in most cases it’s the main IC, which is custom built for Bose.

Hello On pin 9 of the integrated circuit Fan7384 there are connected a resistor with an sot323 ... the sot323 should be bat54cw but i don't know the resistor value ... while connected between diode bridge and fcd7n60 there is a resistor 1210 with written 75 ||| ... is it a 75 ohm? unfortunately on this card there are some things burned and I can't find the values please help me ... thanks

@henryho6203

Жыл бұрын

the resistor marked as 473, should be 4.7K ohm

@ramss.6433

4 ай бұрын

Did you ever fix this?

@dualityrepair4770

4 ай бұрын

I did not. It’s been so long that I forgot what all of the issues were.

@fabiobrasca619

4 ай бұрын

i did not@@ramss.6433

@eduardodominguezruiz3493

26 күн бұрын

that resistor its says 75m but i dont know if it is ohms or miliohms. My is measuring like a fuse but i dont know if this is ok.

Great video. Got the same problem with mine. I got a solition, to run the system. At lest the power supply need to stay always on. „Temporary“ Solution: I bridged 2 contact directly on the texas Instrument chip close to the high frequent capacitor. (You can try with a piece of wire On the whole site of the chip, i tired it also no circuit) After that you can hear the chip „starts“ and the bose sound starts as well. This will work dosent matter if you switch the bose on or off on the remote control. Whenever you disconnect The power you need to bridge the contact again. My bose is running since two days now.

@bertani24

3 жыл бұрын

Can you tell us exactly which pins worked for you? That description is a little bit too generic

@steveulman9805

3 жыл бұрын

Echo Luca's comment - How did you accomplish your solution?

I have the Bose v20 lifestyle 5.1 sound system the sub woofer light flashes amber located next to the power outlet I sent it to Bose for repair paid 200+ Dollards CDN for the repair and came home with a amber flashing on/off

I've reflowed main processor pins and mine is working fine atm.

@fabiobrasca619

Жыл бұрын

On pin 9 of the integrated circuit Fan7384 there are connected a 0603 resistor with an sot323... Can you tell me is value?

I enjoy watching your videos and I realize this is an old video already, however you volume level is far too low, I have my computer speakers on max and I can barely hear you over the sound of the fans.

TO EVERYONE WITH THIS PROBLEM: First, "get a brand new battery for the remote". Then unplug the unit for at least a week, I actually had to go 2 weeks.............then plug the unit back in and wait for the tone. Now, after the tone "WAIT AT LEAST ONE MIN BEFORE ATTEMPTING TO POWER UP". You should get a green light now........................Why does this work??? I have no idea...............but its worked for me twice, since it wouldnt power up, even after the reflash and 5 min inplug. (Id still like to know if the crystal replacement worked or not)..............

@godsuno777

4 жыл бұрын

kzread.info/dash/bejne/nomum5dmpNCWkrQ.html

@danielwarren7353

4 жыл бұрын

How can I turn the unit on without the remote

@godsuno777

4 жыл бұрын

@@danielwarren7353 You cant.........

@danielwarren7353

4 жыл бұрын

@@godsuno777 thanks man

@giovanni4926

3 жыл бұрын

@@godsuno777 This comment helped me fix my Bose Solo Tv with the exact same problem as shown in this video. No power, no light, nothing. Just had to solder 2pcs of 100uf 16v capacitors. No crystal change needed. Thanks!

I have te same Problem with the device.I checkt the resist of every smd cap in range of the Prozessor against the minus pole (mass).1 Darkbrown cap have connection on 2 sides of the cap.And bingo the device Works after chancing cab .The cap was Shortet.Dont forget the cabs at backside. Sorry dude my english is very bad.

Im inspecting one which hast good 24V, but is stuck from time to time and does Not respond. I have some Spikes measured on 1,8 volts which seem Strange. ITS vr701 in Service Manual.

@fabiobrasca619

Жыл бұрын

Hello On pin 9 of the integrated circuit Fan7384 there are connected a resistor with an sot323 ... the sot323 should be bat54cw but i don't know the resistor value ... while connected between diode bridge and fcd7n60 there is a resistor 1210 with written 75 ||| ... is it a 75 ohm? unfortunately on this card there are some things burned and I can't find the values please help me ... thanks

@thomasw6169

Жыл бұрын

@@fabiobrasca619 sorry i have repaired a while a ago and given back, so I can not look up for you.

@fabiobrasca619

Жыл бұрын

@@thomasw6169 ok ok thank you anyway..

Could you provide a link to the crystals, please?

Can Unit Be Powered On Without Bose Remote?

@alanadkins7100

6 ай бұрын

My Remote Is Bad

Wot happened to part 2

how do you know when you use the usb update that it has finished updating?

@dualityrepair4770

4 жыл бұрын

Sorry I’ve never run the USB update so I wouldn’t know.

@dancox6387

4 жыл бұрын

@@dualityrepair4770 damn.

@johnathanpearson3203

3 жыл бұрын

@@dualityrepair4770 any update on the changed crystals? You got me hooked 👍

Usually just unplugging and unplugging the power will bring it around to turning on.

@jcadlols

5 жыл бұрын

BROWNWRENCH BROWN I imagine his would have been unplugged for more than 5 minutes if he bought it on eBay.

@dualityrepair4770

5 жыл бұрын

Nope. Did that 10+ times. It was a much deeper issue than the classic IT help desk response.

@chevyphil3969

4 жыл бұрын

@@dualityrepair4770 THAT'S WHAT MINE DOES WORKS ONLY WHEN UNPLUG FOR FIVE MINUTES SOON AS I SHOUT IT OFF IT won't RESTART AGAIN TIL I UNPLUG IT I DID A REFLASH AND HELPED FOR A WHILE BUT BACK DOING IT AGAIN NOW YOU STILL NEED TO UNPLUG IT FOR FIVE MINUTES OR SO THAN IT WORKS ALL DAY TILL YOU SHOUT IT OFF AFTER FIVE MINUTES IT won't RESTART ANY IN STRESS IN LOOKING AT IT AND SHOOTING ME A PRICE TO FIX IT I TRIED THE ADDRESS YOU GAVE AT THE END OF THIS VIDEO BUT GOT NOWHERE. OF COURSE IM NOT TOO COMPUTER SAVY I GREW UP ON APPLE 2S LOL

Exact same Problem.. Did someone ever wrote Bose about this Design Flaw?

@fabiobrasca619

Жыл бұрын

Hello On pin 9 of the integrated circuit Fan7384 there are connected a resistor with an sot323 ... the sot323 should be bat54cw but i don't know the resistor value ... while connected between diode bridge and fcd7n60 there is a resistor 1210 with written 75 ||| ... is it a 75 ohm? unfortunately on this card there are some things burned and I can't find the values please help me ... thanks

I have run into that sound once before that is the crystal one of those two crystals is making an audible sound and a crystal is not supposed to be making the sound there is something shorting that Crystal there's a component on that board that is shorting that Crystal or the crystal is shorted that's why that Crystal is throwing off and harmonic sound right now that's where that sound of tone is coming from it's coming from the crystal I ran into that once before and I had to replace the crystal

Where's the follow on video please?

Part 2?

Someone can help me please?

Hello Sir I am looking for part two . At the moment I have the same problem . Thanks

@FirstLastth

Жыл бұрын

there is no part 2 unfortunately.

Привет! Есть схема?

I was told a software reflash can cure some of those not powering up issues.

@dualityrepair4770

5 жыл бұрын

I tried unplugging several times without luck. I wish I could try the software flash but the unit was dropped and has been damaged.

@brownwrench

4 жыл бұрын

@@dualityrepair4770 mine has now completely crapped out. No power light...nothing. A reflash helped for a while. Please follow up on the crystal replacement.

@brownwrench

4 жыл бұрын

@@dualityrepair4770 so this stopped the who exercise ? :(

I’m fixing my own Solo at the moment. My Bridge Rectifier blew. I’ve sourced its exact part thanks to a BOM I found, but without a schematic I cannot identify the SMD resistor next to BR1201 marked, “750” which is badly burned in my board. If you have the chance, could you scope it’s resistance? Pretty sure it’s 75 Ohm, [0603], 1/10W, 5%, but the package isn’t 603 so in just double checking

@dualityrepair4770

4 жыл бұрын

Kenneth, sorry I no longer have my Bose. It was dropped and the board cracked so I got rid of it.

@kennethmeyerson1165

4 жыл бұрын

It’s all good, I am fairly certain I ordered the right part 👍. Thanks for making and supporting great content!

@silviuguseila2552

4 жыл бұрын

Kenneth, that is not a "750", please see this picture of a close-up here imgur.com/Sj3F8hC, it's a 75M sort of... Mine is measuring 0, not sure why, maybe you are more advanced with this repair and have a better idea? I am trying to fix mine, nothing blown, but not powering up, no chime, voltages seem ok, but I don't have an oscilloscope to check for ripple and things like that.

Very disappointed now with this unit. It was periodically not working, but unplugging and replugging usually restored it from time to time when it acted up.

@jona639

4 жыл бұрын

Yes, this is what I have to do periodically. I leave it unplugged for 30 mins and hey presto, it works again once I plug it back in. I have the larger unit with the programmable remote but it's obviously the same fix as yourself.

if not id like to buy the remote i have 8 of these

I had exact the same issue. It is the DSP. After replacement it worked just fine again.

@michaziokowski519

2 жыл бұрын

Can you point what exactly you did?

@johannweber4553

2 жыл бұрын

@@michaziokowski519 I replaced the D808K023CPTP4

@michaziokowski519

2 жыл бұрын

@@johannweber4553 thanks. I'll keep that in mind. For now, I just added one capacitor (this one from the top left) and warmed up whole board with hotair. 2nd week and it works with no issues

@fabiobrasca619

Жыл бұрын

DSP need some firmware?

Can’t you just toss the entire board and use the unit for just the speakers? Wire the speakers to an receiver that’s also connected to the tv and your good.

@bobbrown98

2 жыл бұрын

someone want to show how we would do this?

@tevya017

2 жыл бұрын

Sensible solution

@davidwhite9751

Жыл бұрын

That's what I'll probably end up doing. I imagine that a couple of crossover networks will be required.

Remove the 2 cristals and it works ...

@godsuno777

4 жыл бұрын

Do you mean {replace)..........or just remove them??

@BuddhaPinneberg

4 жыл бұрын

Sorry replace

@godsuno777

4 жыл бұрын

@@BuddhaPinneberg Ok..........cool! :) ]

@rebeldrea

3 жыл бұрын

So replacing the crystals fixes the issue?

@dualityrepair4770

3 жыл бұрын

I was not able to try replacing the crystals as the unit was damaged.

Just tell us it’s better to toss the thing away

I don’t wanna do all this. It’s like a year and a half old, and used like 5 times max. Bose is trash. They won’t replace it.

Overpriced junk no longer supported by BOSE. They used to repair these for $99. I tried a flash upgrade. Mine is failed just like yours I have 3, 5 and 24V supplies. Now they just offer you a new one for $280. I'm done with BOSE. I'll buy a $89 piece of junk to replace the $300 BOSE.

@markboo6117

4 жыл бұрын

And you will end up with a better product.

@mgr1956

4 жыл бұрын

Billccm John I just spoke to bose mine has the same issue, they offered me a new solo 500 at half price, but do I really want to buy another?

@silviuguseila2552

4 жыл бұрын

They could just publish the schematic and maybe even the fix and allow people to repair them

@davemarsden1259

4 жыл бұрын

My solo wasn’t working ...well it would work after powering off for short time after that it would crash ...using the fibre optic Input...I then tried the RCA input and it works perfect ran is for 2 days with no issues ...be worth trying

What a piece of crap. Full Microprocessor controlled, full smd junk. This is a curse to have for repair.

@thierryborda4889

Жыл бұрын

sometimes short circuit s102. few times is the diode D1301 to replace. But most of the time it is U705 (TPS62110) faulty. hot air on DTS work sometimes

Do yourself a big favor and NEVER EVER buy anything BOSE. It's garbage

Every Bose device I've purchased has stopped working after a couple of years. It's overpriced junk. I won't be buying any more Bose crap.