Nice to see how all the dirt runs back to nature again...

@FlyingFun.

9 ай бұрын

Hmm, yes I was thinking the same, just like the hoover filter it just releases all the crap out at a different time and place .. Bit like EVs are clean where they are driving but the pollution is still being produced at the coal fired power station.😂😂

@dopiaza2006

3 ай бұрын

that's only the soot from one regeneration cycle. Around 100-200 miles worth of driving. Bit of carbon never did anyone any harm!

@londonboy8547

3 ай бұрын

It came from the ground in first place..

@em4703

25 күн бұрын

Oh no, carbon in the soil. Better there than your lungs, don't you think?

@hokz7283

14 күн бұрын

Its just unburned coal going going back home but in a proper way.

I cleaned mine by removing it and fitting a straight piece of pipe. No more DPF issues and very happy with it. Also blocked off the EGR valve. Of course got an engine light so I removed the lamp. All good now.

@BigVanSmallWorld

7 ай бұрын

Haha way to go 👏👏👏

@danny6574

7 ай бұрын

Hope you know someone who dose bent MOTs 😂😂

@alexhorton7371

7 ай бұрын

If the dpf filters cold start contaminants, won't it pass when you go with a warm engine to the test?

@bossadave

7 ай бұрын

@@alexhorton7371 unfortunately not, their is soot and particulates all across the drive cycle particularly under load. The worst of these are the ultra fine particulates. These are inhaled deep into your lungs 🫁 then move from your lungs to your blood 🩸 stream to damage your heart and brain 🧠. Spare a thought for people that work around diesel fumes daily they are likely to spend their hard earned retirement in poor health.

@honumoorea873

7 ай бұрын

Same here on my 330D

You should go downtown and blow air backwards through the DPF, wafting all the soot into the air, so that the circle of irony is complete.

DPF REMOVAL & CLEAN using Wynn's 18985 5L Off-Diesel Particulate Filter Cleaner Removes Soot & Deposits From DPFs amzn.to/3R2lFc7 Everything i use in my camper van you will find here in my Amazon Store www.amazon.co.uk/shop/melsvanworld Camper van build parts list www.amazon.co.uk/shop/melsvanworld

Well done mister, nice delivery, your a natural & good to see people having a go at stuff.

@BigVanSmallWorld

9 ай бұрын

Thank you kindly!

dpf´s are great , saves all the nasty stuff from going into the enviorment ........to then dump it into the enviorment at a later date along with 4litres of nasty chemicals .

@Dickie2702

9 ай бұрын

I made the the same point and was told to leave Mel alone. Here I a quote from the Safety Sheet for this product "Dispose of contents/container to an approved waste disposal plant." I find I disgusting that that both yours and and my comment are hearted by the man himself. I'm no eco warrior but we all need to realise that just treating the environment with such disregard has consequences.

@mikevolante7663

8 ай бұрын

​@Dickie2702 what's worse, is all the rubber from your tyres you dump every year. 4 tyres, how many grams each? Probably much more than this carbon and far more damaging.

@Dickie2702

8 ай бұрын

@mikevolante7663 You are probably correct and you have to now pay to have tyres disposed of responsibly. But you missed my point, if you are going to upload videos to the Internet and garner a following, then you become, like it or not, an influencer. And, as such, I feel you have to be responsible for the content you are making. Or do you condone people contravening published disposal instructions?

@germancarfan360

7 ай бұрын

You are wrong, soot is emptied out, ash content within the dpf gradually builds up over time, so not all goes out in the environment.

@marppp28

7 ай бұрын

Apart from all this comment I agree he should not tip it in the garden or anywhere near because he possibly growing his own vegetables or at least have apple tree in back garden 👌

I’m SO GLAD I’ve kept good care of my rust-free 2003 Dodge Ram 3500 Cummins! None of this crap to deal with. For over 22 years this thing has run reliably, and other than rebuilding the manual transmission 5 years ago, and the lift pump and the water pump- oil changes and fuel filter changes have been all that Ive ever done.

I lost over £4000 on two cars because of the dpf's. In a few years time there will be adverts saying "did you own a car with a dpf fitted?", and the government will have to pay out millions of pounds for forcing car manufacturers to fit something not fit for purpose! Dpf's totally destroyed the biggest attribute of the diesel engine... Reliability! Shocking! 😠

@558vulcanxh

Ай бұрын

Absolutely Agree with you 😊

@hughmarcus1

Ай бұрын

Those adverts are already out there. They’re just a bluff & going nowhere

@xxwookey

8 күн бұрын

It does add a pile of complexity that make one want to return to the days of simple electromechanical vehicles. The easiest way to simplify things again now is move to an electric motor. You don't need all that anti-pollution kit because there isn't any in the first place. OK, you don't get 700 miles per tank, but you do get clean and quiet (and significantly cheaper motoring if you can charge at home). Seems a reasonable tradeoff.

@hughmarcus1

8 күн бұрын

@@xxwookeyabsolutely. About 50 odd moving parts instead of nearly 1000. Much less to go wrong. An electric motor uses about 30% of the raw energy too.

The company I work for has just had a Ford Courier van's DPF cleaned after the van went into limp, mainly due to it being used for short journeys. The mechanic told me that a regen involves over-supplying diesel, some of which washes down the bores, contaminating the engine oil. The oil level might even rise! He recommends _much_ more regular oil changes, because of this. I like the idea (from another comment) of opening the DPF chamber, throwing away the contents and welding it back up!

@BigVanSmallWorld

9 ай бұрын

Thank you 🙏

@patkelly9907

8 ай бұрын

That will be great until you go for mot do you think they not see it welded you have two problems then

@ParaBellum2024

8 ай бұрын

@@patkelly9907 No, I'm a very good welder, and in any case I'd open up the component at the back, where my deceit would remain hidden after reassembly!

@carlarthur4442

7 ай бұрын

​@RubberBandBoy Naughty, but don't blame you , good job your a good welder then 😉 😅

@ParaBellum2024

7 ай бұрын

@@carlarthur4442 It's a long time since I've worked as a welder, TBH, so the results might not be as impressive as I made out!!

I usually filter tue cleaning fluid thru a coffee filter paper let it settle then pour it off and use it again

You are totally correct Mel all that “on the car cleaning” is cobblers , rarely will it clean properly . I clean DPF’s in a £30k cabinet machine from cars to lorry’s .again you are correct firstly you must clean against the flow of gasses a pressure washer can be used to help as like you have done. Good video Mel helping those that might want to have a go themselves 👍

@BigVanSmallWorld

9 ай бұрын

Thank you for the positive feedback really appreciated 👍🤓👍

@andypandy9045

9 ай бұрын

@@BigVanSmallWorld your positivity helps a lot of people keep up the good work chap 👍

@torquesteer2657

9 ай бұрын

Have a look at O’Reily’s DPF cleaning channel. He uses a mix of Launch UK fluid & water flushed through the DPF whilst it’s still on the car.

@andypandy9045

9 ай бұрын

@@torquesteer2657 I follow him

@trickyfocus

9 ай бұрын

@@torquesteer2657 He gets them to new condition

Excellent way to clear dpf how needs to go to garage looking forward for further video thanks

Thank you Mell..... great as usual.......😊

@BigVanSmallWorld

9 ай бұрын

You are so welcome

Dpf are not fit for purpose. To prevent blocking people who don't do a high mileage have to do a hard run for 40 minutes once a week to keep it clear. How can this be good for the environment.

Mel, could you have brazed the drilled out bolt in place, maybe clamping it in position? Though perhaps tack welding in place will be sufficient. Clever plan to use the bolt to seat the sensor, very resourceful.

@terryjones2012

2 ай бұрын

But it won't be in the correct position

Cleaned mine with the same fluid about 2 months ago, back flushed when rinsin aswell maybe 20-30 times also used air pressure which help blow out some of the red ash at the end and alot of the water. Worked for me lowered my dpf pressure from 250mbar at 3k rpm to 50mbar at the same revs. I also used the same chemical as brick acid which really helped with the red ash was a weakened version but did the job.

@johnpatterson5744

7 ай бұрын

The pressure in the DPF should be no higher than 10 mbar.and one should never let the diesel fuel in the tank drop below a quarter,preferably a half tank of diesel for the DPF to function properly.👍

@beany1987

7 ай бұрын

@johnpatterson5744 50mbar or kpa can't remember at 3k rpm this was directly after cleaning with water still coming out and before it has done a regen aswell. Havnt checked it since, but will check it this weekend and see what it's at now 4 months later.

@s.wilson5675

6 ай бұрын

@@johnpatterson5744 No more than 10mbar on idle, ideally half that and 50mbar at 3krevs is very good AFAIK. The DPF will normally get blocked for a reason.... Built in fault code with some vehicles (around 120k miles), sensors not working, nozzles blocked, etc.

@beany1987

4 ай бұрын

Been 6 months now its flushed all the water, lose soot and Ash out that was broken up by the chemicals along with a few natural regens. The pressure is 6mbar on idle and around 50 at 3.5k so it did the job very well and was very easy to do.

Great video. Best thing for the DPF is a long chisel and a hammer 😉

@BigVanSmallWorld

9 ай бұрын

Great tip! Lol 😂

You are very original meister. Respect👍

@BigVanSmallWorld

7 ай бұрын

Thank you kindly

Great work Mel 👍

@BigVanSmallWorld

9 ай бұрын

Thank you 😁

There are several reasons why there are companies that clean filters. 1. they use hot liquid for washing. 2 they recycle the liquid. 3 their cleaning liquid is filtered and the waste is disposed of correctly. 4 there is a guarantee on their work. Not like your solution, where chemical liquid and particles run directly onto the ground and contribute to contaminating the groundwater. It doesn't matter now, it's your grandchildren who can't drink water, unless it's cleaned WITH chemistry to remove solutions that you and others use now. think about it

Interesting video. Plenty of clever tips. Best wishes from CarSpyTV.

@BigVanSmallWorld

9 ай бұрын

Thanks for watching!

Some medical authorities are now saying that the much finer particles ftom the DPF are more easily absorbed into the lungs than the relatively harmless but smelly pre Dpf ones ever were .😊

I leave the DPF on the vehicle. Just disconnect the exhaust joints and cover the exhaust holes with plastic bags. Then stick the powerwasher lance up its snout. You don't have to disconnect any sensors as they do break unfortunately. I just fitted a new NOX sensor, but all the threads stripped removing the old one. I just drill it out, sit the sensor in place and mig the sensor. Saves a lot of hassle

@BigVanSmallWorld

9 ай бұрын

Nice 👍 thanks for the tip 👍🤓👍

Thanks

Nice logic

did mine an old 520 bmw took it of soaked it in a big bucket with two dishwasher tabs and half a bag of soda crystals for an hour washed it out with a hose and refitted power restored and no lights on cost about a quid 😁😁😁😁😁

@BigVanSmallWorld

9 ай бұрын

Oh brilliant 👏👏👏

@xxwookey

8 күн бұрын

Dishwasher tablets will do a good job of removing oil and soot, but you need an acid after that to get rid of the metallic ash as well. kzread.info/dash/bejne/jKthp6Ocj6_Wpps.html tests 9 chemicals on a chopped-up one to see how well they work in practice.

Top job mell that's exactly how I do mine, keep flushing till there's no foam it can take 45mins with jet wash, the soots not a problem, it's the ash left behind 👍

@BigVanSmallWorld

9 ай бұрын

Good to know thank you 🙏

@timfaulkner852

9 ай бұрын

@@BigVanSmallWorld leave them over nt if you can gives 💯, better results 👌👍👍

a thought Mel, as I wish to remove my DPF ...my idea is to remove the exhaust like yours, then cut a hole through the ceramic to put a straight pipe through, welded to each end. This way it looks like the dpf is there, but the gases are going straight through, and have the dpf shut down on the ecu. :)

@BigVanSmallWorld

2 ай бұрын

That would be an mot fall and it’s against the law to remove the DPF from the vehicle

Great video Mel It’s my next job now I’ve seen how bad my EGR valve and intake manifold was clogged with oil and soot

@BigVanSmallWorld

9 ай бұрын

Good luck 🤞

@patkelly9907

8 ай бұрын

You need to ask your self were is the oil coming from There should be no oil EGR and DPF we're designed for dry soot and ash only

@One_over_the_eight

7 ай бұрын

​@@patkelly9907 Crankcase breather pipe. It's normal to have some oil residue going through the intake. The unfortunate part is the oil vapour mixes with sooty EGR gases in the intake manifold and turns to gunk attaching itself to components and over time clogs everything up.

You'll have the environment agency on the blower,about contamination of the ground from washing it outside 😂

Amazing 👍👍

Just wondering does anyone know oven cleaner or WD-40 work?also how long will that cleaning out filter last for cheers

Great video sir.. Thank you..

@BigVanSmallWorld

3 ай бұрын

So nice of you

I wonder if you could get a ultrasonic actuator from one of those ultrasonic cleaners, attach it to the dpf and see if you could get the cleaner to cavitate and therefore super activate the cleaner.

@BigVanSmallWorld

7 ай бұрын

I have absolutely no idea 🤷‍♂️

Hello, I want to clean my Prius 3 catalytic converter. Do you know can I use this product for my car? Thanks

Excellent video. After refitting do you need to tell the ecu it's been cleaned/renewed or can you just clear the dtc code.

@BigVanSmallWorld

8 ай бұрын

Yes I’m told that is exactly what I need to do video coming up soon 👍🤓👍

Nice video Mel.

@BigVanSmallWorld

6 ай бұрын

Thank you that’s very kind of you to say 👍🤓👍

wow Great job yang man well done 😀👌

@BigVanSmallWorld

2 ай бұрын

Thanks 😁

Years ago I looked after forklift trucks in chemical plant, they had large honey Combe spark arresters on the exhaust, always used pressure washer, but importantly they were allowed to dry in a heated room, otherwise the soot stuck to them very quickly, like you see on videos in situ loads of steam but builds up too quick if not dried. 👍

@BigVanSmallWorld

7 ай бұрын

Thanks for the advice 👍

I cleaned the dpf on my Range Rover on the car with 100% success and will do at every service with lots less hassle

@randoshanks

2 ай бұрын

Care to share how you cleaned your DPF? Did you use the same method or a different method?

@geomoto599

2 ай бұрын

@@randoshanks I followed same method as O’Rileys Autos on you tube used wynns dpf cleaner pumped fluid in pressure pipe before dpf lots of videos on you tube also sprayed dpf cleaner in air intakes as per revive product video on KZread.

@558vulcanxh

Ай бұрын

How just to help others please 😊

I have a MK6 Golf had DPF issues after about 2 weeks of owning it. Gutted the DPF, remapped the car no issue since that’s 6 years ago DPF is a waste of time

Mel you should of put Evapo Rust on the hole thing £16 from Tool station Now on sale was £22

The way the filters are made it work forwards and backwards. I think a fire hose from the back would be best though. These filters are a total pain and the regens do not work well, my older diesels had no problems with these or the ADBLUE because they were not there.😊

Did my crv dpf this week. Bit of a bastard to get out as its right down the front of the engine and a heat shield gets in the way. Once out cut the heat shield corner and you will makes life alot easier. The chemicals and additives just dont work. Save your money. Just take it out and clean it. Jetwash, chemical soak, jetwash. Back in , force a regen and its good as new.

I broke one of the sensors when doing that on my wifes X trail. After i was told "you didnt need to do that" I did have trouble getting it dry, Blew air thro after draining and flushing from a workshop vac outlet connected to the pipe and heated the pipe in front of the core with a blow lamp on and off for about 30 minutes.

@BigVanSmallWorld

6 ай бұрын

Well done 👍

How would you unblock a sink?

How many liters of the Wynn’s DPF Cleaner was needed to fill your DPF? What year is your Sprinter?

Cleaning the dpf on the van is also an option , i used manol dpf cleaner injected through the pressure sensor pipe . Works without taking dpf off , which is very tricky on renault trafic as high up behind engine.

@BigVanSmallWorld

7 ай бұрын

Thank you

@dopiaza2006

3 ай бұрын

This worked perfectly for me on a 2010 Audi TT TDI. Was in limp mode and soot load was so high it was beyond the level for forced regeneration. Mannol DPF cleaner in from the top reduces the load far enough that forced regen was successful and all is good now.

You will get better results with your welding if you prepare the area you are going to weld by cleaning it as much as you can. A wire wheel or brush works good.

@BigVanSmallWorld

5 ай бұрын

Thanks for the tips

Sent you a comment regarding the vario

The main reason the contaminants dont flow through the filter is because the particle size is too big. by using a solvent the dissolved contaminants can become smaller than the filter can hold and it will exit, so those on-car cleaning methods *can* work, but taking it off and cleaning in both directions is by far the best way.

Great video mate, just a quick one would I able to undo that nut on the pipe that connects to the exhaust that holds the thin pipe? Access on mine is very limited, I can only access that nut with that thin long pipe. Was thinking undoing it and spraying cleaner inside it.

@BigVanSmallWorld

2 ай бұрын

Yes, absolutely

change the wing mirror for the DPF problem, the outside temp sensor may be missing or damaged.

@BigVanSmallWorld

4 ай бұрын

It’s all fixed now thanks though 👍

great logic and engineering. hope it all works ok. i wouldnt be suprised though if the sensor is M14 X 1.5 and the standard M14 bolt you fitted is a X 2.0mm pitch thread.

@BigVanSmallWorld

9 ай бұрын

You’re absolutely rite but I did manage to work it on 👍👍

@harryboy3305

9 ай бұрын

@@BigVanSmallWorldright not rite

@john-ec6sy

9 ай бұрын

@@BigVanSmallWorld aah good. hope you're feeling alot better and the motors running well 👍

I vrone down up scotland blocked DPF so ordered a reconed one from DPF clean team down Lester £750 😱 causw of the blocked DPF was a machanic fitting a cheap sensor and couldnt delete the engine management light which wouldnt allow the DPF to regenerate. Cost me a thousand pound in total and ruined trip.

That filter should be oven dried after wet cleaning before it is reinstalled.

So,they put these filters on the vehicle so it doesn't polute or contaminate the enviroment but loads of people are flushing them out like yourself (and i'm not pulling you on it as i would do exactly the same) with some kind of detergent/chemical and then rinsing it down the drain or into the nearest grass verge etc which then contaminates the enviroment,what nonsense. I just cannot see any difference between the old steam engines were they had to clean the soot and clinka out of the boilers and this dpf filter,it's ridiculous. Great video glad you got the soot and clnka out 😀👍

how does a DPF get blocked on a camper? we use a camper for holidays, weekends or even day trips - usually all long(ish) journies including motorways or dual carriageways. Never had an issue with DPF.

@BigVanSmallWorld

5 ай бұрын

Good question!

Cleaning a dpf while in place is often a cheaper and easier option due to the location of the dpf and due to exhaust sections being seized together. But, it does not clean as well as removing the dpf and back flushing to clean it.

@BigVanSmallWorld

7 ай бұрын

Yeah I know

Hi Mel have you tried just putting petrol mixed into the diesel makes the engine run bit hotter but clears the DPF my truck fitter gave me the idea and it worked put about one gallon of petrol into a full tank of diesel .worked on my Renault Master van?

@BigVanSmallWorld

7 ай бұрын

This could seriously damage your fuel pump I wouldn’t recommend doing that

Do you know if it is necessary to reset the ECU once you change the DPF with the scanner or a regeneration to get the new values from the differential pressure probes?. I have to change it for a new one, it is very saturated.

@BigVanSmallWorld

5 ай бұрын

Yes you do 100% i had to have this done on mine but i was sick at the time so didn't film it sorry. good luck with yours

@cransaftvalve734

5 ай бұрын

@@BigVanSmallWorld I have not scanner. Ummm. Thanks.

Hot soap an water probably do the same thing

Hi Mel were you getting any driving or performance issues prior to doing this clean out.

@BigVanSmallWorld

9 ай бұрын

Yes was going into limp mode 👍

@donner101

8 ай бұрын

@@BigVanSmallWorld Thanks. Did you get any dash warning lights showing up when it was going into limp mode.

i buy oil that comes from under the ground and then use it for a while, and then poor it back into the ground and call that 100% recycling! As oil it came and as oil it will return, amen!

Wynns. Great Australian car products.

All this off vehicle DPF cleaning and DPF filter blockage can be avoided completely if the DPF self regeneration process took place as the vehicle system saw necessary. However if your fuel gauge is always below 1/4 level , the ECU will NOT kick in the self regeneration process….ending with a filter so blocked that forced regeneration with diagnostic tool or self regeneration becomes ineffective.

@BigVanSmallWorld

9 ай бұрын

Interesting that thank you 🙏

@donner101

8 ай бұрын

Hi by self regeneration do you mean just driving the van until it clears out itself?

@nkakaputa9293

8 ай бұрын

@donner101 Yes sir. As long as the DPF has not been left to point of blockage the system will periodically self clean.... the ECU looks at the fuel level to commence this process. Because of the extra fuel required to achieve the high temperatures.

@johnpatterson5744

7 ай бұрын

Yes the pressure within the DPF should be no higher than 10 mbar.and ensuring your running the level of diesel in the tank no lower than a quarter full,preferably at least half full ensures the DPF will function effectively.👍

@coffeeguy6673

6 ай бұрын

Some vehicles wont do a self regeneration if the ambient temp sensor is faulty or if the vaporiser is blocked in the exhaust, this is where fuel is squirted into the system to burn off the soot.

1/4 pool acid 37%- will do the job as well :)))) I think you broke not heat sensor, this is particular matter sensor- it reads pressure and sends info to computer. This is how you find out that dpf is blocked.

i had problems with me last kuga had to remove the dpf to clean it. did clean it before via dpf pressure sensor tube this worked just as well as the removal watching the pressure drop on my forscan system. then doing DPF rest the values. the biggest problem is people don't investigate correctly as to why the DPF regen is not working in the first place to keep it clean. Mel this could be to the fact that your DPF pressure sensor is faulty. also make sure that your sensor when you get fits in place and goes as deep into the exhaust as the original or you could get incorrect readings. that sensor works like a 02 sensor it needs exhaust flow over it hence the holes in it.

@BigVanSmallWorld

9 ай бұрын

That’s so true

it doesnt matter which way its flushed, best not to use narrow stream or turbo nozzle pressure washer on ceramics. soot doesn't matter, it can be flushed out after soaking in dishwasher tab or washing liquid, its the red ash that needs dissolving. wynns works to a point and needs 2 days, actually coca-cola works pretty much the same. alloy cleaner or HCL works better and does the job in 2-3hours,

Hello... during cleaning should I remove the sensors off the dpf

@BigVanSmallWorld

4 ай бұрын

I’m not sure if you have to I did and I broke my so if ever I need to do it again I wouldn’t remove them good luck with yours

If you drive plenty it should never need doing. My work transit has never had an issue and currently on 170000 I do 250/400 miles a day I guess that’s the trick

@BigVanSmallWorld

9 ай бұрын

I think you could be right 👍🍻

Can you name all the tubes and wires going on to the dpf? it's not all sensors are they?

@BigVanSmallWorld

8 ай бұрын

Basically yes they are the one I broke was a heat sensor the two pipes are for a pressure sensor that senses the difference in pressure between the inlet and outlet of the DPF if the pressure is high on the inlet side and low on the outlet this tells the ECU that the DPF is blocked 👍

@BigVansmallWorld Your reasoning for taking off the dpf to be cleaned is flawed. The dpf captures the bigger particles created at lower temperatures when the engine is cold. Then burns them off during the regen allowing them to passthrough the filter. Blowing a cleaning solution into the dpf dissolves the soot into small enough particles allowing it to passthrough the filter.

Would the high pressure from the washer do damage to the dpf

@BigVanSmallWorld

Ай бұрын

Not at all it’s been working great ever since

@ItsBigJC

Ай бұрын

@mel I have a problem you may have come across mate. I have a 2017 sprinter - pooling water in the footwell by the pedals. Heavy rain is giving me water . The material against the firewall is soaked Checked the roof and around the window seals and can’t find anything untoward Anywhere else I should check ?

You really need to put a warning on this video about the hazard of using the cleaner and your consequences, as others may go ahead without realising the dangers.

The reason why dpf additives are used inline with the flow is because they make tue ash burnable thus allowing the filter to catalyze it , still a nasty process for the enviroment

Hey Mel handy having that drainage ditch to wash all the Crap into .

@BigVanSmallWorld

9 ай бұрын

Yeah just like all them people that wash their cars every weekend 👍

@Dickie2702

9 ай бұрын

Congratulations for creating your own environmental disaster! I'm no eco warrior but I really can't approve of your disposal method.

@danielhines5698

9 ай бұрын

That's what happens on a regeneration....drive up the motorway and all the crap flies out the back ..... leave Mel alone

@Dickie2702

9 ай бұрын

@danielhines5698 In a normal regeneration cycle the soot is burnt off at high temperature, very different to removing soot by chemical methods. Slightly different to using a chemical flush and then pouring the resultant debris in an open ditch. I'm sure Mel is a lovely chap but he is in this case setting a very poor example. Sorry if that offends you or Mel but sometimes the truth hurts. I

@gorillacyclist

9 ай бұрын

​@@Dickie2702it's soot that's basically carbon. Carbon actually absorbs lots of bad stuff - it's used in NBC suits and filters and such, so while looks dirty it's ok. No worse than emptying a BBQ.

Hi Mel I know it says off car but is it possible to do this on vehicle as I don’t have the means or place to remove it ?

@BigVanSmallWorld

27 күн бұрын

yes you can but to be honest i would take it to a garage and get them to do it for you

@whippetsadventuresandoneman

27 күн бұрын

@@BigVanSmallWorld unfortunately I don’t have the funds to take to a garage. I’ve used everything including the foam dpf cleaners and it’s still saying dpf on my scanner. Now again goes into limp mode switch off and on the van drives fine again. Getting fed up. Starting to feel my ecu is fucked because ever time I scan it comes up with other sensors then I scan again and there gone :( I sick of these modern vans

Ure karcher is knackered its pulsing

Might have just been easier to buy a new bung for the sensor and just weld that in

@BigVanSmallWorld

Күн бұрын

Yeah but I couldn’t get one

Can you updates us please? Did your dpf lights came back?

@BigVanSmallWorld

2 ай бұрын

All ok 👍 not had a problem since

@_-lover-_736

Ай бұрын

How many months have you travelled since last dpf clean up? By the way i think you are an amazing guy thanks for your this video.

My Karcher make the same noise as yours when trigger not squeezed.

@BigVanSmallWorld

9 ай бұрын

Interesting 🤔

@smifff63

9 ай бұрын

It’s not normal, I’ve had mine about 20yrs and it started doing it last yr, it pulsates like yours, no idea why.

@jondor654

9 ай бұрын

Possibly one or more broken springs on plungers . If so can be replaced as I did for a clone. Fiddly but extends useable life aka eco friendly

@smifff63

9 ай бұрын

@@jondor654 Thanks.

...... "I'll be right back" *talks back to phone screen: you're not going anywhere boy!! 🤣🤣🤣🤣

@BigVanSmallWorld

9 ай бұрын

I’m really sick right now sorry i didn’t end the video like I usually do 🙏

Never mind the dpf how did you manage to sharpen the drill bit on that wheel.never works for me. 😂

@BigVanSmallWorld

7 ай бұрын

Years of practice 😊👍🍻

I cut my transit one open and there was just two white blocks in there, chucked em away and welded it back up and it passed the test no bother 😊

@BigVanSmallWorld

9 ай бұрын

Nice work!

In theory your right, in actual fact you are incorrect. Wet cleaning is just as effective from the 'inlet' end of the DPF especially if the DPF is near vertical such as a Mercedes S class. One other point, is the heat sensor going to be at the right depth into the gas flow...

@BigVanSmallWorld

9 ай бұрын

Thank you 🙏

Good job

@BigVanSmallWorld

9 ай бұрын

Thanks

Gut DPF. Have a remap deleting adblue ( if used).

@BigVanSmallWorld

7 ай бұрын

That’s e legal

@leonardgoldberg2879

7 ай бұрын

@@BigVanSmallWorld And.......

@No-timeforimbeciles

6 ай бұрын

You do not have a DPF &🎉 ADD BLUE in same vehicle, it is one or the other !

That's probably why a lot of companies clean a dpf on the vehicle? You went from a £60/100 job to £500 or more depending on vehicle ! BUT you have only fixed a symptom of a fault that was causing your dpf to not be doing regens to burn away the soot ! Usually when they block it's because of ASH that needs cleaning but soot is usually a different problem !

@BigVanSmallWorld

9 ай бұрын

You’re right there thanks for that 👍😂👍

Are you going to tell us the dpf is still showing a problem and actually it was the exhaust back pressure sensor (£45)?

@BigVanSmallWorld

7 ай бұрын

No not at all it’s actually working fantastic now I have cleaned it and reset the ECU

Hi have you put the end result after refitting on KZread

@BigVanSmallWorld

3 ай бұрын

Yeah it’s all good 👍

Crossed fingers that Fred is the right pitch. 🤞😂

@BigVanSmallWorld

9 ай бұрын

Thank you 🙏

It’s Kenny Everitt , hello fans mr diy here

@BigVanSmallWorld

2 ай бұрын

I'll take that cheers 👍😆👍

When mine gets blocked it's getting deleted

fantastic clip for nature conservation everything from the DPF goes straight to the ground... well done he will now pay the fine for the ecological disaster

"That's nasty".Procedes to flush down the drain.

Why not cut the broken bit off completely and the manufacture a new bit then weld it on?

@BigVanSmallWorld

9 ай бұрын

I did something like that

The fluid they put in the DPF dissolves the soot and the engine pressure pushes it out ,and launch fluid works better mate ,but I could see the method in your madness, any how not every body has the time to do this method they need the car for work

@eziozomparelli2079

8 ай бұрын

Dpf aren't so expensive if you replace your self and maybe 1hour of your time.

Stroooth mate ..dramas are comin outta the wood work .. cencers..heat deeetecters ..good grieff chieff ..😂🤣😂..anywho ..you.ll figure it oot ..😁pip pips

@BigVanSmallWorld

9 ай бұрын

Thanks for the well wishes 😂🤣🙏👍

0:39 that was a quick check

@BigVanSmallWorld

7 ай бұрын

I don’t mess around 😂