Dominator Industries Meathooks Installed on a Road Glide, in your Garage!
Автокөліктер мен көлік құралдары
(Yeah i know in the video ! say Mayhem) It is not as hard as you think. Do it yourself and save some money!!
#baggernation #diy #harleydavidson #project #roadglidespecial #ciro3d #customdynamics #advanblack #advanblack #bars #handlebars
Order here 👉 www.dominatorcycles.com/colle...
Пікірлер: 38
Good video install is as easy as putting it together backwards of how you took it off
about to order the same bars, this will help huge!
@kr3garage
Жыл бұрын
Happy to help
Did you need the clutch cable and brake line extensions? Working on mine right now and I am being told that 12 inch bars need those. Not an issue currently because mine is apart and I am at the point of reassembly.
@kr3garage
Жыл бұрын
No I used to stock cables with the 12”
@parkerlanier7858
10 ай бұрын
@@kr3garage Did you have to pull the clutch and brake line out to get more? I currently have my Roadglide apart and have No wiggle room with the Lines and I bought the 10". Was there a clip inside or zip tie on the lines restricting them from giving me more? Also, did your bars come with the throttle already in them, or did you remove your stock one and put it in the bar?
@kr3garage
10 ай бұрын
I used the stock cables. It was pretty tight for 12” but worked
How did you extend your brake and clutch cables?
@kr3garage
4 ай бұрын
Didn’t need to the factory will fit up the 12 inch
You said the shorter bars help with your hands going numb??? I currently have 10 inch bars and was told I needed to go to 16 inch to help with that??
@kr3garage
3 ай бұрын
My hands went incredibly numb with 14’s the 12’s helped my situation.
@jaredroberson8049
3 ай бұрын
@@kr3garage thanks for the reply you just saved me a bunch of money then
Im sorry i must have missd it.. how tall are those bars?
@kr3garage
6 ай бұрын
Those are 12 inch
@Steve_10-31
6 ай бұрын
Thanks😊@@kr3garage
Is that color the Twisted Cherry?
@kr3garage
Ай бұрын
Hot rod hard candy
So to be clear, you bought the 100% prewired bars? Which meant you didn't have to pull ANY WIRES....correct?
@kr3garage
Жыл бұрын
Correct
@vinnypandolfo6195
Жыл бұрын
@@kr3garage Thanks for your speedy response!
@vinnypandolfo6195
11 ай бұрын
The bars came out great! Those mirrors though 😮 love the new grips too!
These are the 12”?
@kr3garage
Жыл бұрын
Yes
How did you cut the nubs off?
@jonesnaround
Жыл бұрын
Never mind I used a hammer and chisel , couple of hits came right off.
@kr3garage
Жыл бұрын
Dremel
@harleycrasher8396
Жыл бұрын
I used flat head screwdriver and a hammer, 2 hits, done!
@harleycrasher8396
Жыл бұрын
14 inch dominator meet hook 100% pre wired. Moved both clutch and throttle cables to get more length and fit 2021 RGS. Hope this helps.
@Ryan-oq7oq
8 ай бұрын
@@harleycrasher8396any issues with controls sliding around after removing the nub ? Thought about just drilling holes in the bars .
This basically shows the break down but not the install. Wasted time.
@kr3garage
Жыл бұрын
Please feel free to e-mail me with questions you have or if you need help. I’d be happy to assist. 🤙
@felixsilva7863
Жыл бұрын
@KR3 Garage thanks I appreciate it. I'll be getting bars next month and am looking for as much info as I can possibly find to install them.
Did a three year old make this video
@kr3garage
9 ай бұрын
Yea thank you for noticing. And practicing the golden rule