Doing an OVERHAUL on the NASKART Build! Time to Actually Make MAJOR Progress!
Автокөліктер мен көлік құралдары
Hey Guys, Migs Here! In today’s video, I am working on the Half Scale NASCAR and on revamping the build, I start off by doing the whole fuel system legitimately, and doing the first oil change in 20 years on the new engine! Also, I show some new parts and plan with the build that will make it get done even quicker and better! Thanks for Watching! Please Subscribe, Like, Comment and Tell Your Friends About the Channel!
Пікірлер: 207
Add a barb fitting to the gas tank for the return line.
Drill and tap the tank to except a hose barb pipe fitting
I'd definitely replace the oil filter the paper element turns to dust if left in for too many years!
Yoo CARS AND CAMERAS USED 2 carbs from GO POWERSPORTS its half the price. Watch there video
@mattriella6776
4 жыл бұрын
yeah but that thing is so under powered and sounds like literal shit cause of the half assed tuning they did.....
You might want to get a bigger fuel tank
Love the build progress! Keep grinding Migs! As far as the return line, I would personally drill a hole towards the top of the gas tank and JB weld a fitting to accept that size of hose. I think drilling it into the cap would cause problems in the future.
@sethkrahn3155
4 жыл бұрын
The gasoline will eat away at the jb weld
@trail-tr2ql
4 жыл бұрын
Seth Krahn from what I’ve tested jb will hold up to gasoline. I’ve used it on gas tanks and it’s still holding fine
@NastyMoto
4 жыл бұрын
Seth Krahn In some cases yes but I just made a gas tank out of a aluminium water bottle with JB weld and it’s holding up great, I think it just needs to be mixed right and the surfaces need good prep
@sethkrahn3155
4 жыл бұрын
My bad then lol
@trail-tr2ql
4 жыл бұрын
Seth Krahn lol your good, just sharing my experience
You need a bigger fuel tank man!! And get some decent fuel line. By the time you fill up all that fuel line your probably down half a tank. Lol 4 carbs use.more fuel than you think
@markpojda3466
4 жыл бұрын
Ya that tank is not going to give you more than 10 minutes!
You need to run actual fuel line. Those are more for vacuum hoses
Use brass barb with a threaded male end and drill right next to the cap. Use some plumbers tape and make sure that your male threaded end is tapered. Good luck that should work for you. Also put a peice of thin rubber between tank and pump
I've been waiting for your video all day keep up the good work Mig's!!!!!
@motomigsofficial
4 жыл бұрын
Thanks!!
I would get a hose barb and thread it to to the gas tank drill and tap a hole for the return line. Keep up the good work man
Bro don’t worry about it this build needs time take as much as time as you need dont rush this build I would rather wait months and this build be done right and no problems then see it built quick and break🙂 love the vids keep up the good work
@motomigsofficial
4 жыл бұрын
Thanks for the support man! 💪🏻
I’m assuming you read my comment last video it’s good that you took those comments into consideration without getting offended great video
Great vid
Good job exhaust looks close to the tank the heat off of it will be bad also you could put a 90 on pump
i would have dies=d out laughing if you dropped your phone in the oil 15:50
Re-do the welds and make sure you can trust them
A twin Mukunni carburator set up for a Honda 750 engine will work very well. Your right. It sounds like it's running on 2 cylinders.
Moto migs you’re Doing some amazing work on that project and fixing all the flaws on the project,I enjoy watching your videos and look forward to seeing the nascart project finished.
@motomigsofficial
4 жыл бұрын
Thanks!! I appreciate it!
G'day Migs I hope your using the correct motor oil for motorcycles if you use friction modified oil , your clutch will slip when under load . For the tank you should Get a nut riveting tool , this will make it so you can , drill the top of the tank then put the threaded rivet in then tighten by squeezing the handles together this will seal it's self ,then get a threaded barb with a 90% bend the size you need for your fuel line this should help you . Hey I'm glad you are asking questions things will run smoother when you do , make sure you read all the comments, that way you can understand what we are trying to advise you to do. We are here to help !
Almost a 100k subs!!! 👌🏽
Drill a hole in the tank and add a rubber gromet to make sure the line doesn’t pull out easy, keep on going all most done👍🏾
Try drilling and tapping an spot in the top of the tank and add a fitting because I've seen a few people do it that way and it has worked for them.
To get it to stay in the gas cap even hot glue might work
@supertedogpriken
4 жыл бұрын
hot glue does NOT like fuel.
You could drill a hole in the tank and put the fuel line in with a rubber grommet to create a seal : )
Drill a hole in the tank and put a fiting on it to accept the fuel line
@malcolmdavis506
4 жыл бұрын
A high speed fan would also be a benifit pointing downward to push it out the back .
the 4 carb setup works great , you just dont know what youre doing
I like how the NASCAR its coming out.just take your time.the only thing i cud recommend its get your self some atv ramps at harborfreight so u do struggle as much .good vid
Video #203 still sitting in shed not working 😂
@daverayburn013
4 жыл бұрын
And really really all he does is run his mouth ..i really really think hes on meth
Bruh!! I hope im wrong but did you just mount the fuel talk by the exhaust header exit? Your making a bomb my man. Keep em coming!! HAha
You should cut vents into the back window to allow the heat to escape
@playinwithfirecustoms7954
4 жыл бұрын
I was gonna say the exact same thing. I think you should get a 2-2&1/2" hole saw and do 3 or 4 rows of holes.
@motomigsofficial
4 жыл бұрын
That’s a great idea I haven’t thought of that, thanks man!
Also check the inside of the hose your planing on using for your naca ducts. It has to be smooth. if it's ribbed in the inside (And probably is) It will be very restrictive for that application and flow little or no air. Since the pressure is very limited.
Loving the videos keep it up i think it needs a new shifter i think just drill a hole in the tank and seal around the hose
@malcolmdavis506
4 жыл бұрын
G'day mate yeah I suggested he should make the shifter with a pivot point at the top of the shifter leaver and one at the other end where the gear leaver is . Unsure if that's on the list , for the return line use a riveting tool and a 90%
Run a tee fitting before the fuel pump and run the return line to it. Also make sure the fuel lines have slack they don’t need to be tight that’s just asking for them to eventually come loose.
Hey there awesome progress bro 🤗 I'm not trying to be a smart ass but did you remember to fully re tighten up the oil drain bung ? you would be very surprised at how many people do 😲 just put it back by hand just to stop it dripping while they checkout the oil or empty the oil tray when they were originally going to let it continue dripping overnight to get out the real thick gunge/buildup 😉 25 years ago a mate did it with a Honda just like mine and it fell out during a ride 🙄 the bike still run being a Honda but was beyond repair and I always leave the bung in the socket so I will never actually replace it without using the socket and tighten it up completely 🤗 great job and show thank you
Don't forget to get a good quality 5 point in there I have a feeling it's gonna roll at some point
You have the hose for the the NACA ducts but do you have the actual Duct? You can order those pretty cheap too.
You can drill a hole in the side of the gas tank and put a valve stem in and take out the valve core i belive standard fuel hose is the righ size to hose clamp to the valve stem and that could be your return line thats what i would do
not to hate or anything but in a streetbike engine you want to run motorcycle oil or rotella t6. it has the right additives for wet clutch systems
the pressure regulator is has fuel in line out and return is they a vacume pipe needed to manifold to know when to regulate or is it just like an air compresser would use with the problem you had i wounder if that the problem or maybe the fuel pump is not upto it another idea is a fuel pump for a motor cycle they have a live a neg and a feed wire to the live wire of coil number one to know when to pump and this is how they regulate when the engine was running i could see air traverling up the feed to the carbs so something is not set right and drawing in air
for the return pipe put it between the fual tank and the pump with a t connector
Drain the fuel tank, drill a hole, and mount a compression fitting (something with a gasket tp prevent leaks). You might even be able to use an old petcock valve.
You should do a crossover video with cars and cameras and have them check out the kart and ask questions about what you need to do!
Drill a hole in the black part of the tank, and thread a brass nipple into the hole, so then the gas line can be attached to it
For the return line drill a hole in the gas cap and put a gromet in the hole that holds the pipe
For the fuel system you can drill a hole and weld a bung hole kinda like and o2 sensor and screw a fitting in and attatch a fuel line.
@quancast1141
4 жыл бұрын
K Z obviously
@malcolmdavis506
4 жыл бұрын
@K Z yeah that's true , I suggested he use threaded riveting tool that will seal it's self , then there's no chance of explosion , and little bits of Migsy all over the work shop , or fireball Migsy running around the back yard stop drop & rolling . Mal.
What happend to the solex?
Drill a hole in the fuel tank for the return line and then silicone around it
Get a bigger gas tank with a return line on the top, that small tank will keep running out every 15 mins...
I would say for the gas tank use a 1/4" barb to 3/8" hex fitting with a nut on the back
👍🏻👍🏻👍🏻👍🏻👍🏻
Drill and tap the tanks for the return line
Idk how well braided fuel line is but I'd try that so it doesn't crack or melt
Build an awning on the front of your little shed , more room . And no fumes .
hype
Yo migs you should have welded it in stead of drilling holes through the frame
@talanpeterson6882
4 жыл бұрын
@K Z he needs mounting lessons, and you need some grammar lessons
Where is your fuel cell that was on the kart does it not have a return line option on it plus it would be safer also you need to run steel line as much as possible with proper rubber fuel line and clamps for safety
It is only running on 2or3 cylinders and the carbs need to come off be cleaned and synched.
Just drill into the gas cap and put a rubber grommet on the line and and it should seal well in the cap
Always keep the battery charge all the time when you work on the half nas car man
You could drill a hole in ur gas tank put a fitting in and jb weld it in or gasket maker would hold it in
👍🏼
Plz use proper fuel line 😟, also get a bigger tank. You could put a nipple on the tank top and have your return line attached to it. Make sure you use Wet clutch oil if it's not already and replace the oil filter now, if the old ones been sitting that long it'll bugger up all your hard work. Get a jumper pack, half your time is spent charging a battery 👌
@malcolmdavis506
4 жыл бұрын
Some good advice Mate !
That big engine looks good but how fast will it go
Weld a bung to the top of the gas tank for return
@zacheryrobinson1301
4 жыл бұрын
james edmiston plz don’t make him weld anything and definitely not the gas tank
I would recommend a new filter, the oil might not look extremely bad I personally would recommend it to get more life out of this engine. I think you should let it sit and run for about 20-30 min and drain that oil that you just put in so you can clear out all the old mucky oil and throw on a new filter and put some full synthetic 10w-40 In with a new filter that is meant for full synthetic and let it sit and run for 10 min or so with the new oil then after 3,000 miles replace the oil again but keep it full synthetic, once you switch to full synthetic you don’t want to switch back and forth between regular and synthetic. That’s what I recommend for a clean flush out of that old gross oil. :)
Migs check out the cars and camera channel with the 4 into 2 carbs they did it on their cross cart.
LOL thats a dead head holley style regulator not a bypass regulator. It has one inlet and 2 outlets . Commonly used on carbs with 2 float bowels. It is not good for low volume because once it shuts the flow it dead heads the pump. You maybe able to rig up one outlet as a leak to avoid dead heading the pump but you will give up to much volume during high fuel demand. Invest in a bypass regulator or try it with no regulator. Those cheap inline pumps come in different pressures maybe find one with 3-4 psi.
Put a brass nipple on the cap and a hose clamp or a zip tie
Drill a hole on the gas tank towards the top Tethlon tape the end of a nipple and the screw it in
What do u work as
Weld a metal adapter into the gas cap for the line
Service the whole thing , and you might think of a bigger tank , a plastic one could be your best bet due to the size and weight
just plug the return line its not needed, i have run the same setup on a cb750 when i ran alcohol, also you bought the wrong pump, it makes to much pressure, the right pump doesn't need a regulator, but having said that you don't need a pump, just mount a gas tank above the engine, the needle and seat in your carbs are for gravity feed.
people have been saying ffrom day 1 to get a jumper pack. Just imagine conecting a jumper pack and starting the go kart or bike vs charging a battery for 4-6 hours, and then maybe starting it. Use your head and be smart here.
Try putting a fitting on the gas cap if that doesn’t work try gasket make gas gas resistant
I don't think you need a return line just put about 5 psi to it and it should be fine they say a carb can handle around 8 psi
And also do not use that pool hose for an air duct line there will be to much restriction and it is not big enough for that motor use 3" pvc and flare out the ends of the BBC in front
@malcolmdavis506
4 жыл бұрын
Good advice Mate.
Drill a hole in tank and then put a big boden connector in there
Weld a fitting to the gas cap
Drill a hole into the actual gas tank and use a metal valve stem for like a vehicle and put it in there it won't go anywhere and you can put your liner as you return
Just put a T fitting before the fuel regulator for the return
Get a battery tinder and keep it on it. It will always be charged
On the fuel pump just put a cap on the overflow and then the gas will flow evenly on the fuel line !!!!!!!
Hey , you should get n stronger feul pump otherwize you are going ro have bogging issues.👌
Still will like because I want to see this project finished but you sure there's going to be progress all you did was change fluids and check stuff.
Ur taking forever
@CoronaBRP
4 жыл бұрын
I'm sure he has other financial priorities.
Empty gas tank drill and tap you a hole for a barb fitting for return
Drill and tap a barb fitting in the top of your tank and boom... you got a return.
@landonmcgill9292
4 жыл бұрын
Erik Young the gas tank walls are too thin u can’t tap it
@malcolmdavis506
4 жыл бұрын
That's true , use a thread figuring tool .
@malcolmdavis506
4 жыл бұрын
Fuck Spell check , riveting tool
@Midori_Erik
4 жыл бұрын
Malcolm Davis that would be the best due to his welding skills being very novice
Sup
Just get a connector and put the return line into the fuel line! Near the start of the line!
@quancast1141
4 жыл бұрын
Doesn’t work that way
@Sam-m04
4 жыл бұрын
12oclock Quan it could-like a closed loop system. Just running around in a circle
You drill the hole 1 size smaller than the hose it’s the same concept as a weed eater I’ve done it before it will be fine
Buy a new battery if you have a issue with the battery keep grinding MIGs its almost done
Can you bring back Steve?
@juice3906
4 жыл бұрын
Everything Yamaha ikr
Look okay, I am not hating but we have been making major progress for a year
Get a Metal hose splice drill a hole in the tank and weld it in
Drill a hole in the gas tank and put a barbed fitting on
Drill a hole in the gas cap and epoxy it or silicone it into place
@haydenbruce2790
4 жыл бұрын
Steven Perkins exactly
Use a gromet for the return
What about the chocolate head studs u put in ie threaded bar ? Also plate u mounted pump on way to thin ! Why don’t you reach out to a welder get him to guide you maybe weld up jack shaft properly.its a nice cart but you have bodged it up bad
@lyndonwebber1389
4 жыл бұрын
Get a fitting to weld in tank